User Manual - CNC4PC

More documents

Recommendations

Info

5-3-7 Setting rotation direction Motor rotation direction in speed mode can be set by parameter Cn004 (Motor rotation direction) and input contact SPDINV according to the tables below. Caution! Both methods can be operated at the same time. Ensure that these parameters are set correctly for the required direction. Parameter Name Setting Description Motor rotation direction (observation from load side). No. Torque control Speed control 0 Counter Colckwise (CCW) Counter Colckwise (CCW) Control mode Cn004 CCW 1 Colckwise (CW) Counter Colckwise (CCW) S/T CW 2 Counter Colckwise (CCW) Colckwise (CW) 3 Colckwise (CW) Colckwise (CW) Input contact SPDINV Description Control mode 0 Rotation by speed command direction. 1 Rotation by reverse speed command direction. S Note: Input contacts status “1” (ON) and “0” (OFF). Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection. 5-17
5-3-8 Speed Loop Gain In speed mode there are two speed controller loops, with separate Gain ( P) and Integral (I) functions. Speed controllers 1 or 2 can be selected by setting one of the multi- function input terminals, to selection G-SEL or by setting one of the parameters Cn20-Cn24 as required. Please refer to section 5-3-11 section B for more details. Parameter Name Default Unit Setting range Control mode Sn211 Speed loop gain 1 40 Hz 10~450 Pe/Pi/S Sn212 Speed loop integral time constant 1 100 x0.2 ms 1~500 Pe/Pi/S Sn213 Speed loop gain 2 40 Hz 10~450 Pe/Pi/S Sn214 Speed loop integral time constant 2 100 x0.2 ms 1~500 Pe/Pi/S Diagram below shows the speed controller. Setting a high speed loop gain or a lower speed loop integral time provides a faster speed control response time. For more details refer to section 5-5. Kv 1 1 TS i Kv: Speed Loop Gain (Hz) Ti: Speed Loop Integral Time Constant (sec) 5-18
Page 2 and 3:
■Warning and Alert: Warning • D
Page 4 and 5:
Contents Chapter 1 Checking and Ins
Page 6 and 7:
5-6-7 Selecting the External Regene
Page 8 and 9:
1-1-2 Confirming with Servo Motors
Page 10 and 11:
1-3 A Brief Introduction of Operati
Page 12 and 13:
1-4-2 Direction and Distance Fan Fa
Page 14:
1-5-3 Notice for install motor 1. P
Page 17 and 18:
2-1-2 Wiring for Servo Drives • T
Page 19 and 20:
2-1-4 Motor Terminal Layout A Table
Page 21 and 22:
2-1-5 Typical Wiring for Motor and
Page 23 and 24:
2-1-7 Wiring for Mechanical Brake R
Page 25 and 26:
2-2-1 Output Signals from the Servo
Page 27 and 28:
Explanation of General I/O Signal F
Page 29 and 30:
(b) Digital I/O Signal: For many ki
Page 31 and 32:
Digital Input Function Explanation
Page 33 and 34:
Digital Output Function Explanation
Page 35 and 36: (c) Pulse Command Input Interface C
Page 37 and 38: (f) Analog Output Interface Circuit
Page 39 and 40: (2) Name and Explanation of I/O Sig
Page 41 and 42: 2-3-2 Position Control Mode (Pe Mod
Page 43 and 44: 2-3-4 Speed Control Mode (S Mode) R
Page 46 and 47: Chapter 3 Panel Operator / Digital
Page 48 and 49: Once the first parameter in a param
Page 50 and 51: Step Control Keys LED Display after
Page 52 and 53: 3-2-2 Diagnostic function Following
Page 54 and 55: dn-03 (Input terminals status) Use
Page 56 and 57: dn-07 (Auto offset adjustment of ex
Page 58: dn-08 Display Motor Standards Cn030
Page 61 and 62: 4-1 Trial Operation Servo motor wit
Page 63 and 64: Steps for setting JOG function: Ste
Page 65 and 66: B. Trial run in Speed control mode(
Page 67 and 68: C. Position control mode trial run
Page 70 and 71: Chapter 5 Control Functions 5-1 Con
Page 72 and 73: 5-2-1 Analog Torque command Ratio.
Page 74 and 75: 5-2-3 Torque command linear acceler
Page 76 and 77: 5-2-5 Internal Torque Limit In torq
Page 78 and 79: 5-3 Speed Mode Speed Mode is necess
Page 80 and 81: 5-3-2 Analog speed command Ratio An
Page 82 and 83: Parameter Name Default Unit Setting
Page 84 and 85: Setting example: (1) To achieve 95%
Page 88 and 89: 5-3-9 Notch Filter The function of
Page 90 and 91: 5-3-10 Torque limit of speed contro
Page 92 and 93: (1) PI to P mode switch over by com
Page 94 and 95: (B) Automatic gain 1& 2 switching S
Page 96 and 97: (3) Automatic gain 1&2 switch condi
Page 98 and 99: 5-3-12 Other Functions When the spe
Page 100 and 101: Speed Feed Back Smooth Filter When
Page 102 and 103: Two types of pulse command can be c
Page 104 and 105: For internal positioning mode there
Page 106 and 107: 5-4-3 Electronic Gear Electronic ge
Page 108 and 109: 4.Parameter Setting for Electronic
Page 110 and 111: 5-4-4 Smooth Acceleration Using the
Page 112 and 113: 5-4-7 Clear the Pulse Offset In pos
Page 114 and 115: Parameter Name Setting Description
Page 116 and 117: Home routine Timing Chart During th
Page 118 and 119: (2) Pn365.0=1or 3. After starting t
Page 120 and 121: (5) Pn365.0=2. After Starting HOME
Page 122 and 123: 5-4-9 Other Position Function In po
Page 124 and 125: Speed Loop Gain Speed Loop Gain has
Page 126 and 127: 5-5-1 Automatic Adjusting This devi
Page 128 and 129: Process for Auto tuning The Diagram
Page 130 and 131: 5-5-3 Improving Resonance The Servo
Page 132 and 133: Parameter Name Description ★Hn502
Page 134 and 135: 5-6-2 Switch for the Control Mode S
Page 136 and 137:
Timing for Brake output signal Set
Page 138 and 139:
5-6-7 Selecting for External Regene
Page 140 and 141:
Assess for an external resistor and
Page 142 and 143:
In such applications, calculate ER
Page 144 and 145:
Chapter 6 Parameter 6-1 Explanation
Page 146 and 147:
Parameter Name & Function Default U
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Parameter Sn213 Sn214 Sn215 Speed l
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Parameter Name & Functions Default
Page 168 and 169:
Quick Set-up Parameters Parameter N
Page 170 and 171:
Parameter Signal ★Hn502 ★Hn503
Page 172 and 173:
Parameter Signal Name & Function De
Page 174:
Diagnosis Parameter Parameter Name
Page 178 and 179:
(2) Read consecutive 2 words from d
Page 180 and 181:
7-1-3 Modbus communication protocol
Page 182 and 183:
ASCII Mode Framing Symbol Name Desc
Page 184 and 185:
06H:Write Single Register Write a w
Page 186 and 187:
10H:Write Multipile Registers Conti
Page 188 and 189:
CRC Checking: CRC check code is fro
Page 190 and 191:
Low-Order Byte Table /* Table of CR
Page 192 and 193:
RS485 RS232 0024 51BH Cn036 Servo I
Page 194 and 195:
Address RS485 RS232 Parameter Name
Page 196 and 197:
Display parameters Address RS485 RS
Page 198 and 199:
Example: Following table are proced
Page 200 and 201:
Alarm Code Alarm Name and Descripti
Page 202 and 203:
Alarm Reset Methods 1. carry out th
Page 204 and 205:
Position Control Mode Command Sourc
Page 206 and 207:
※ Dimension for TSTA-15 and TSTA-
Page 208 and 209:
※ Dimension for TSTA-50 and TSTA-
Page 210 and 211:
TSB 07/08 SERIES SPECIFICATION 1(kg
Page 212 and 213:
TSB 13 SERIES SPECIFICATION 1(kgf.c
Page 216 and 217:
Appendix A: Peripheral for Servo mo
show all

User Manual - CNC4PC

Create successful ePaper yourself

Delete template?

Save as template?