User's Manual - Nikon

More documents

Recommendations

Info

Turn the Scanner On Before turning the scanner on for the first time, confirm that the Nikon Scan 3.1 CD is in your computer’s CD-ROM drive. Press the power switch to turn the scanner on. When the scanner is turned on, the status LED will blink for a few seconds while the scanner initializes and then glow steadily. When turning the scanner on, be sure that no holder is inserted. Leaving a holder in place can prevent the scanner from initializing normally. The status LED should blink slowly (about twice every three seconds) while the scanner initializes. If the LED flashes rapidly (about five times a second), there may be a problem with the scanner or with the connection to your computer. Try turning the scanner off, waiting for five seconds, and then turning the scanner on again. The first time you run Nikon Scan, the status LED will emit five series of rapid blinks (each of about three seconds duration) when you first insert a holder with the scanner on or if you start Nikon Scan for the first time with the scanner on and a holder in place. This does not indicate an error. Do not eject the holder. If you ejected the holder while the status LED was blinking, turn the scanner off and then on again and restart Nikon Scan. 26 Pg. For more information on: 27 Device Registration (Windows Only) 131 Troubleshooting Status LED
Device Registration (Windows Only) The first time you connect the scanner to a Windows computer, you will need to “register” the scanner with the system by installing the hardware drivers. ○ ○ ○ ○ ○ ○ ○ ○ Windows XP XP Home Edition/Windows Edition/Professional XP Professional . 28 Windows .................................................................... 2000 Professional ...................... 28 34 Windows 2000 Millennium Professional Edition ...................... (Me) .......... 34 42 Windows 98 Millennium Second Edition Edition (SE) (Me) ............. .......... 48 42 Windows 98 Second Edition (SE) ............. 48 27
Page 1 and 2: ○ ○ ○ ○ User’s Manual Set
Page 3 and 4: Product Documentation The documenta
Page 5 and 6: Use an appropriate power supply Use
Page 7 and 8: Notice for customers in Canada CAUT
Page 9 and 10: Film Holders for the 8000 ED ......
Page 11 and 12: Setup This chapter describes how to
Page 13 and 14: Get to Know Your Scanner Your Scann
Page 15 and 16: CD-ROM CD-ROM CD-ROM CD-ROM CD-ROM
Page 17 and 18: Protect Your Film The Digital ICE p
Page 19 and 20: Installing the IEEE 1394/Firewire I
Page 21 and 22: Installing the Drivers for the IEEE
Page 23 and 24: Windows Millennium Edition (Me) The
Page 25 and 26: 4 5 6 7 Select The updated driver (
Page 27 and 28: Installing the IEEE 1394 Update for
Page 29 and 30: 3 4 5 Click Next to install Nikon S
Page 31 and 32: Installing Nikon Scan on a Macintos
Page 33 and 34: 4 5 6 Once the Nikon Scan program f
Page 35: Connecting the Scanner The first ti
Page 39 and 40: 3 4 5 6 Select ls8000xp.inf Select
Page 41 and 42: 5 Confirm that the scanner is worki
Page 43 and 44: 4 5 6 7 Select ls8000xp.inf Select
Page 45 and 46: 3 4 5 Select Specify a location Sel
Page 47 and 48: 9 The dialog shown at right will be
Page 51 and 52: 4 5 6 7 8 Select the search option
Page 53 and 54: 3 4 5 Click Finish Click Finish to
Page 57 and 58: 4 5 6 7 Select the search option Se
Page 59 and 60: Navigate to “C:\windows\system32\
Page 61 and 62: Confirming Device Registration (Win
Page 63 and 64: Updating the Device Driver (Windows
Page 65 and 66: Scanning This chapter describes how
Page 67 and 68: With the holder oriented so that th
Page 69 and 70: Openings are provided in the upper
Page 71 and 72: Step 4—Scan the Slide The actual
Page 73 and 74: 1 2 Choose the type of film to be s
Page 75 and 76: If the thumbnail drawer is too smal
Page 77 and 78: 5 Adjust scan settings For steps 6
Page 79 and 80: 7 Compensate for defects Click the
Page 81 and 82: 9 Choose an output size and resolut
Page 83 and 84: 10 Adjust color, contrast, and shar
Page 85 and 86: 11 Click the Scan button to begin s
Page 87 and 88:
13 Exit Nikon Scan and turn the sca
Page 89 and 90:
Film Holders for the 8000 ED This c
Page 91 and 92:
Using the FH-835S Holder for 35-mm
Page 93 and 94:
Openings are provided in the upper
Page 95 and 96:
Inserting Film and Masking Sheets C
Page 97 and 98:
Using the FH-835M Holder for Mounte
Page 99 and 100:
Once scanning is complete, press th
Page 101 and 102:
Insert the film with the matte emul
Page 103 and 104:
Once scanning is complete, press th
Page 105 and 106:
When scanning Use 16-mm film strips
Page 107 and 108:
Thumbnails are displayed in the thu
Page 109 and 110:
Using the FH-869G Glass-Covered Hol
Page 111 and 112:
3 4 5 With the shiny surface of the
Page 113 and 114:
Using the FH-869GR Glass-Covered Ro
Page 115 and 116:
The film angle can be adjusted up t
Page 117 and 118:
Using the FH-816 Holder for 16-mm F
Page 119 and 120:
Inserting Film and Masking Sheets M
Page 121 and 122:
Removing Film from the Holder Open
Page 123 and 124:
Thumbnails are displayed in the thu
Page 125 and 126:
Nikon Scan This chapter provides a
Page 127 and 128:
5 Follow the on-screen instructions
Page 129 and 130:
A B C D E F G H I Control area Cont
Page 131 and 132:
Media Type Menu 1 When using the FH
Page 133 and 134:
The Preview Button Clicking this bu
Page 135 and 136:
Unsharp Mask Unsharp mask increases
Page 137 and 138:
Reference This chapter includes mai
Page 139 and 140:
Cleaning the Scanner Before cleanin
Page 141 and 142:
Troubleshooting Should you encounte
Page 143 and 144:
Problem Possible Cause Your compute
Page 145 and 146:
Scanning time Duration of Scanning
Page 147 and 148:
Specifications for Optional Holders
show all

User's Manual - Nikon

Create successful ePaper yourself

Delete template?

Save as template?