MPLAB ICD 3 In-Circuit Debugger User's Guide
MPLAB ICD 3 In-Circuit Debugger User's Guide
MPLAB ICD 3 In-Circuit Debugger User's Guide
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>MPLAB</strong> ® <strong>ICD</strong> 3 <strong>In</strong>-<strong>Circuit</strong> <strong>Debugger</strong> User’s <strong>Guide</strong><strong>ICD</strong>3Err0012: Download debug exec failedIf you receive this error while attempting to program from the <strong>Debugger</strong> menu:1. Deselect the debugger as the debug tool.2. Close your project and then close <strong>MPLAB</strong> IDE.3. Restart <strong>MPLAB</strong> IDE and re-open your project.4. Reselect the debugger as your debug tool and attempt to program your targetdevice again.If this does not work, see Section 7.3.4 “Corrupted <strong>In</strong>stallation Actions”.<strong>ICD</strong>3Err0013: NMMR register write failed.<strong>ICD</strong>3Err0014: File register write failed.See Section 7.3.2 “<strong>Debugger</strong>-to-Target Communication Error Actions”.<strong>ICD</strong>3Err0015: Data transfer was unsuccessful. %d byte(s) expected, %d byte(s)transferred.See Section 7.3.3 “<strong>Debugger</strong>-to-PC Communication Error Actions”.<strong>ICD</strong>3Err0016: Cannot transmit. <strong>ICD</strong> 3 not found.The debugger is not connected to the PC.<strong>ICD</strong>3Err0017: File register read failed.<strong>ICD</strong>3Err0018: NMMR register read failed.<strong>ICD</strong>3Err0019: Failed while reading emulation registers.<strong>ICD</strong>3Err0020: Failed while writing emulation registers.See Section 7.3.2 “<strong>Debugger</strong>-to-Target Communication Error Actions”.<strong>ICD</strong>3Err0021: Command not echoed properly. Sent %x, received %x.<strong>ICD</strong>3Err0022: Failed to get <strong>ICD</strong> 3 version information.<strong>ICD</strong>3Err0023: Download FPGA failed.<strong>ICD</strong>3Err0024: Download RS failed.<strong>ICD</strong>3Err0025: Download AP failed.See Section 7.3.3 “<strong>Debugger</strong>-to-PC Communication Error Actions”.<strong>ICD</strong>3Err0026: Download program exec failed.If you receive this error while attempting to program from the <strong>Debugger</strong> menu:1. Deselect the debugger as the debug tool.2. Close your project and then close <strong>MPLAB</strong> IDE.3. Restart <strong>MPLAB</strong> IDE and re-open your project.4. Reselect the debugger as your debug tool and attempt to program your targetdevice again.If this does not work, see Section 7.3.4 “Corrupted <strong>In</strong>stallation Actions”.<strong>ICD</strong>3Err0027: Bulk transfer failed due to invalid checksumSee Section 7.3.3 “<strong>Debugger</strong>-to-PC Communication Error Actions”.Also, ensure that the cables used are the correct length.<strong>ICD</strong>3Err0028: Download device database failedIf you receive this error:1. Try downloading again. It may be a one-time error.2. Try manually downloading. Select <strong>Debugger</strong>>Settings, Configuration tab, andclick Manual Download. Select the highest number .jam file and click Open.<strong>ICD</strong>3Err0029: Communication failure. Unexpected command echo response %xreceived from <strong>ICD</strong> 3.See Section 7.3.3 “<strong>Debugger</strong>-to-PC Communication Error Actions”.DS51766A-page 54© 2008 Microchip Technology <strong>In</strong>c.
Change language