Model 7002Switch System Instruction Manual - Advanced Test ...

More documents

Recommendations

Info

[:ROUTe] subsystemIEEE-488 ReferenceResponse message::int5:list? (Interlock #5, List 1):int5:list2? (Interlock #5, List 2)List of channelsDescriptionThese commands are used to define the lists for the interlocks. The <strong>Model</strong> 7002 has five channelinterlocks. Each interlock is made up of two user-defined lists of channels. Each channel in onelist is interlocked to each channel in the other list. In general, channels that are interlocked cannotbe closed at the same time. More detailed information on the interlocks can be found in Section4 of this manual.Lists for up to five interlocks can be defined. The following examples demonstrate various formsfor expressing a locklist:Locklist1!1 Single channel.1!6, 2!3!6, 6!6 Multiple channels.3!1:3!10 Range of channels.3!1:3!10, 5!2 Range entry and single channel entry.M36 Channel pattern stored at memory location M36.An interlock can be disabled by emptying one or both of its lists. For example, the followingprogram message disables Interlock #1::int:list (@)If you specify channels to be interlocked and they are already included in the Scan List and/ora Channel Pattern (interlock violation), then the entire Scan List and/or Channel Pattern iscleared (lost).Programmingexample10 OUTPUT 707; “:int:list (@ 1!2)”20 OUTPUT 707; “:int:list2 (@ 3!6)”30 OUTPUT 707; “:int:list?; list2?”40 ENTER 707; A$50 PRINT A$60 ENDLine 10 Places channel 1!2 in List 1 of Interlock #1.Line 20 Places channel 3!6 in List 2 of Interlock #1.Line 30 Queries Lists 1 and 2 of Interlock #1.Line 40 Addresses 7002 to talk.Line 50 Displays Lists 1 and 2 (@ 1!2); (@ 3!6).After the above program is run, channels 1!2 and 3!6 will be interlocked to each other. That is,these two channels cannot both be closed at the same time.5-87
IEEE-488 Reference[:ROUTe] subsystem5.13.6:CONFigure Commands::BBMake [:ROUTe]:CONFigure:BBMake Control Break-Before-Make switchingParameters = 0 or OFF Disable Break-Before-Make switching= 1 or ON Enable Break-Before-Make switchingDefaultsPower-up*RST:SYSTem:PRESetSaved power-on setupOnOnQuerycommand:BBMake?Short-form formats:Response message:Query Break-Before-Make:conf:bbm?1 (on) or 0 (off)DescriptionWhen scanning, recalling saved channel patterns or in the Single Channel mode, enablingBreak-Before-Make will assure that the currently closed channel will open before the next channelcloses.When Break-Before-Make is disabled, the assurance that the current channel will open beforethe next channel closes is lost. In other words, two channels could momentarily be closed at thesame time. An advantage to disabling Break-Before-Make is an increase in speed.Programmingexample10 OUTPUT 707; “:conf:bbm off; bbm?”20 ENTER 707; A$30 PRINT A$40 ENDLine 10Line 20Line 30Disables Break-Before-Make and then queries its status.Addresses the 7002 to talk.Displays the status of Break-Before-Make (0; off).5.13.7:SCHannel [:ROUTe]:CONFigure:SCHannel Control Single Channel modeParametersShort-formformats = 0 or OFF Disable Single Channel mode.= 1 or ON Enable Single Channel mode.:conf:sch 5-88
Page 1 and 2:
®Established 1981Advanced Test Equ
Page 3 and 4:
WARRANTYKeithley Instruments, Inc.
Page 5 and 6:
Manual Print HistoryThe print histo
Page 7 and 8:
If you are using a test fixture, ke
Page 9 and 10:
Table of Contents1 General Informat
Page 11 and 12:
4.10.3 Scanning examples ..........
Page 13:
5.13.4 :FCHannels ................
Page 16 and 17:
List of Illustrations2 Card Install
Page 18 and 19:
6 Theory of OperationFigure 6-1 Mod
Page 20 and 21:
8 MaintenanceTable 8-1Table 8-2Tabl
Page 22 and 23:
General Informationthorized repair
Page 24 and 25:
Card InstallationNOTEIf using the s
Page 26 and 27:
3Getting Started3.1 IntroductionThi
Page 28 and 29:
Getting StartedWARNING: INTERCONNEC
Page 30 and 31:
Getting StartedSLOT 112ROW34COLUMN
Page 32 and 33:
Getting Started3.6 Overview of scan
Page 34 and 35:
Getting Started3.7.2 Close and open
Page 36 and 37:
Getting Started2. If the scan list
Page 38 and 39:
Getting Started3.8 Switching card c
Page 40 and 41:
Getting Started3.9.2 Close and Open
Page 42 and 43:
Getting StartedSCPI (Standard Comma
Page 44 and 45:
Getting Started3.10.5 Abbreviated s
Page 46 and 47:
Getting Started20 OUTPUT 707; “:s
Page 48 and 49:
4Front Panel Operation4.1 Introduct
Page 50 and 51:
Front Panel OperationAnnunciatorsTa
Page 52 and 53:
Front Panel Operation3COLUMNSLOT 1
Page 54 and 55:
Front Panel OperationNot all Model
Page 56 and 57:
Front Panel Operationthe VFD which
Page 58 and 59:
Front Panel OperationFront panel ke
Page 60 and 61:
Front Panel OperationSlot 111 2 3 4
Page 62 and 63:
Front Panel Operation4.8 Channel li
Page 64 and 65:
Front Panel OperationStep 3. Enter
Page 66 and 67:
Front Panel Operationd. Click the I
Page 68 and 69:
Front Panel OperationIdleOPEN ALLId
Page 70 and 71:
Front Panel OperationChannel layerN
Page 72 and 73:
Front Panel Operationsatisfy a chan
Page 74 and 75:
Front Panel OperationExample 3:ARM
Page 76 and 77:
Front Panel Operation6. To store th
Page 78 and 79:
Front Panel Operation8. The INFO ke
Page 80 and 81:
Front Panel Operation4.12.2 GPIBThe
Page 82 and 83:
Front Panel OperationPerform the fo
Page 84 and 85:
Front Panel OperationPlace the curs
Page 86 and 87:
Front Panel OperationThe message in
Page 88 and 89:
Front Panel Operation4.14 Scan conf
Page 90 and 91:
Front Panel OperationTable 4-7 (con
Page 92 and 93:
Front Panel Operationline. Perform
Page 94 and 95:
Front Panel Operation2. To retain t
Page 96 and 97:
Front Panel OperationPerform the fo
Page 98 and 99:
Front Panel Operation4.14.4 Channel
Page 100 and 101:
Front Panel Operation3. Interlocked
Page 102 and 103:
Front Panel OperationPin 7 - Digita
Page 104 and 105:
Front Panel OperationCHANNELREADY4.
Page 106 and 107:
Front Panel OperationFor this test
Page 108 and 109:
Front Panel OperationDUT#11OUTPUTDU
Page 110 and 111:
Front Panel OperationBypass7002Pres
Page 112 and 113:
Front Panel OperationDUT#11OUTPUTHI
Page 114 and 115:
Front Panel Operation7002Press STEP
Page 116 and 117:
Front Panel OperationINOUTTriggerLi
Page 118 and 119:
Front Panel Operationmeter to measu
Page 120 and 121:
5IEEE-488 Reference5.1 Introduction
Page 122 and 123:
IEEE-488 ReferenceIEEE-488Table 5-1
Page 124 and 125:
IEEE-488 ReferenceNOTEController pr
Page 126 and 127:
IEEE-488 ReferenceTriggerTransition
Page 128 and 129:
IEEE-488 ReferenceStandard Event St
Page 130 and 131:
IEEE-488 ReferenceThe filter can be
Page 132 and 133:
IEEE-488 ReferenceArm Condition Reg
Page 134 and 135:
IEEE-488 ReferenceAlwaysZeroLay2Lay
Page 136 and 137:
IEEE-488 ReferenceAlwaysZeroSeq1(B1
Page 138 and 139:
IEEE-488 Reference5.6.6 Questionabl
Page 140 and 141:
IEEE-488 ReferenceReading this regi
Page 142 and 143:
IEEE-488 ReferenceB6 is called the
Page 144:
IEEE-488 Reference:ABORt*RST:SYST:P
Page 147 and 148:
IEEE-488 ReferenceWith the Manual c
Page 149 and 150:
IEEE-488 Reference5.8.2 IFC (interf
Page 151 and 152:
IEEE-488 Reference5-32
Page 153:
IEEE-488 Reference• While ignorin
Page 156 and 157: IEEE-488 Referenceas command paths.
Page 158 and 159: IEEE-488 ReferenceResponse messages
Page 160 and 161: IEEE-488 Reference5.10 Common comma
Page 162 and 163: IEEE-488 Reference5.10.1 *CLS ⎯ c
Page 164 and 165: IEEE-488 Referencewhere; CME (bit B
Page 166 and 167: IEEE-488 Reference5.10.4 *ESR? ⎯
Page 168 and 169: IEEE-488 Reference5.10.5 *IDN? ⎯
Page 170 and 171: IEEE-488 ReferenceNOTESee *OPC?, *T
Page 172 and 173: IEEE-488 ReferenceAfter *OPC? is ex
Page 174 and 175: IEEE-488 Reference5.10.9 *RCL ⎯ r
Page 176 and 177: IEEE-488 ReferenceTable 5-5Default
Page 178 and 179: IEEE-488 Reference5.10.12 *SRE ⎯
Page 180 and 181: IEEE-488 Reference5.10.13 *SRE? ⎯
Page 182 and 183: IEEE-488 ReferenceBit 5, Event Summ
Page 184 and 185: IEEE-488 Reference5.10.16 *TST? ⎯
Page 186 and 187: IEEE-488 ReferenceLine 70 Wait unti
Page 188 and 189: IEEE-488 ReferenceSCPI command subs
Page 190 and 191: IEEE-488 Reference5.11 :DISPlay sub
Page 192 and 193: :DISPlay subsystemIEEE-488 Referenc
Page 194 and 195: :DISPlay subsystemIEEE-488 Referenc
Page 196 and 197: IEEE-488 Reference5.12 :OUTPut subs
Page 198 and 199: IEEE-488 Reference5.13 [:ROUTe] sub
Page 200 and 201: [:ROUTe] subsystemIEEE-488 Referenc
Page 218 and 219: IEEE-488 Reference5.14 Sense subsys
Page 220 and 221: IEEE-488 Reference5.15 :SOURce subs
Page 222 and 223: IEEE-488 Reference5.16 :STATus subs
Page 224 and 225: :STATus SubsystemIEEE-488 Reference
Page 246 and 247: IEEE-488 Reference5.17 :SYSTem subs
Page 248 and 249: :SYSTem SubsystemIEEE-488 Reference
Page 250 and 251: IEEE-488 Reference5.18 Trigger subs
Page 252 and 253: Trigger subsystemIEEE-488 Reference
Page 254 and 255: Trigger subsystemIEEE-488 Reference
Page 256 and 257:
Trigger subsystemIEEE-488 Reference
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
6Theory of Operation6.1 Introductio
Page 268 and 269:
Theory of Operation6.3 Control func
Page 270 and 271:
Theory of Operation6.4 Relay contro
Page 272 and 273:
Theory of OperationID data is conta
Page 274 and 275:
Theory of OperationFromDigitalBoard
Page 276 and 277:
Theory of Operationµ DINConnectorT
Page 278 and 279:
MaintenanceNOTEThe digital and disp
Page 280 and 281:
MaintenanceFuse replacement procedu
Page 282 and 283:
Maintenance7.6 Instrument disassemb
Page 284 and 285:
Maintenance7.6.5 Power supplies rem
Page 286 and 287:
Maintenance8. Press “1”, “1
Page 288 and 289:
MaintenanceEDIT ERR REM TALK LSTN S
Page 290 and 291:
MaintenanceTo review the error, pre
Page 292 and 293:
MaintenanceTrigger 8 (STI8) is set
Page 294 and 295:
MaintenanceDETAIL AREF:GRN/YELWIRE#
Page 296 and 297:
MaintenanceBOARDS MUST BE HANDLED W
Page 298 and 299:
MaintenanceSTEP 1FA-151-1, FASTENER
Page 300 and 301:
MaintenanceDETAIL ACC-47, CABLEDIG
Page 302 and 303:
Maintenance8#4-40x1/4"PFH(4 REQ'D)(
Page 304 and 305:
Replaceable Parts
Page 306 and 307:
Replaceable Parts
Page 311 and 312:
Replaceable PartsTable 8-2Digital b
Page 313 and 314:
Artisan Scientific - Quality Instru
Page 315:
(+5V)**(+5V)**** ****** **********
Page 318 and 319:
Replaceable PartsTable 8-3VFD displ
Page 322 and 323:
Replaceable PartsTable 8-4Backplane
Page 324:
Artisan Scientific - Quality Instru
Page 327 and 328:
Replaceable Parts
Page 331 and 332:
Replaceable PartsTable 8-6Miscellan
Page 333 and 334:
Interface Function CodesTable A-1Mo
Page 335 and 336:
Controller ProgramsIBM PC/XT/AT wit
Page 337 and 338:
Controller Programs10 DEF SEG=&HC40
Page 339 and 340:
Controller ProgramsHewlett-Packard
Page 341 and 342:
Controller ProgramsBUS.INIT\ Initia
Page 343 and 344:
CASCII Character Codesand IEEE-488
Page 345 and 346:
ASCII Character Codes and IEEE-488M
Page 347 and 348:
IEEE-488 Bus Overviewtype of instru
Page 349 and 350:
IEEE-488 Bus Overviewdevice will re
Page 351 and 352:
IEEE-488 Bus OverviewLAG (Listen Ad
Page 353 and 354:
IEEE-488 Bus OverviewTable D-2Hexad
Page 355 and 356:
EIEEE-488 Conformance InformationIn
Page 357 and 358:
FSCPI Conformance InformationIntrod
Page 359 and 360:
SCPI Conformance InformationTable F
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
IEEE-488.2 Common CommandsMnemonic
Page 367 and 368:
SCPI Command SubsystemTable H-1DISP
Page 369 and 370:
SCPI Command SubsystemTable H-4SENS
Page 371 and 372:
SCPI Command SubsystemTable H-6 (co
Page 373 and 374:
SCPI Command SubsystemTable H-8 (co
Page 375 and 376:
QuickBasic and QuickC ProgramsMicro
Page 377 and 378:
QuickBasic and QuickC ProgramsMicro
Page 379 and 380:
Index:ABORt 5-134:BBMake 5-88:CLOS
Page 381 and 382:
Scanning channels 4-20Scanning exam
Page 383:
Specifications are subject to chang
show all

Model 7002Switch System Instruction Manual - Advanced Test ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?