Model 7002Switch System Instruction Manual - Advanced Test ...

More documents

Recommendations

Info

SCPI Conformance InformationTable F-1Syntax of SCPI confirmed commands implemented by <strong>Model</strong> 7002Command:DISPlay[:WINDow[1]]:TEXT:DATA :DATA?:STATe :STATe?:WINDow2:TEXT:DATA :DATA?:STATe :STATe?:ENABle :ENABle?[:ROUTe]:CLOSe :STATe?:CLOSe? :OPEN |ALL:OPEN? :SCAN :POINts?:STATus:OPERation[:EVENt]?:ENABle :ENABle?:PTRansition :PTRansition?:NTRansition :NTRansition?:CONDition?:ARM[:EVENt]?:ENABle :ENABle?DescriptionPath to locate message to top display.Path to control user text messages.Define ASCII message “a” using up to 20 characters.Query text message.Enable (1 or ON) or disable (0 or OFF) message mode.Query text message mode (0 or 1).Path to locate message to bottom display.Path to control user text messages.Define ASCII message “a” using up to 32 characters.Query text message.Enable (1 or ON) or disable (0 or OFF) message mode.Query text message mode (0 or 1).Turn on (1 or ON) or turn off (0 or OFF) the front panel display circuitry.Query state of the display (0 or 1).Close specified channels.Query list of closed channels.Query state of specified channels (1 = closed, 0 = open).Open specified (or all) channels.Query state of specified channels (1 = open, 0 = closed).Define scan list.Query number of channels in scan list.Path to control operation event registers:Query event register.Program the enable register.Query enable register.Program the positive transition register.Query positive transition register.Program the negative transition register.Query negative transition register.Query condition register.Path to control arm event registers:Query event register.Program the enable register.Query enable register.F-2
SCPI Conformance InformationTable F-1 (continued)Syntax of SCPI confirmed commands implemented by <strong>Model</strong> 7002Command:STATus:OPERation:ARM:PTRansition :PTRansition?:NTRansition :NTRansition?:CONDition?:SEQuence[:EVENt]?:ENABle :ENABle?:PTRansition :PTRansition?:NTRansition :NTRansition?:CONDition?:TRIGger[:EVENt]?:ENABle :ENABle?:PTRansition :PTRansition?:NTRansition :NTRansition?:CONDition?:QUEStionable[:EVENt]?:ENABle :ENABle?:PTRansition :PTRansition?:NTRansition :NTRansition?:CONDition?:PRESet:QUEue[:NEXT]?:ENABle :ENABle?:DISable :DISable?:SYSTem:PRESet:VERSion?:ERRor?DescriptionProgram the positive transition register.Query positive transition register.Program the negative transition register.Query negative transition register.Query condition register.Path to control the sequence event registers:Query event register.Program the enable register.Query enable register.Program the positive transition register.Query positive transition register.Program the negative transition register.Query negative transition register.Query condition register.Path to control trigger event registers:Query event register.Program the enable register.Query enable register.Program the positive transition register.Query positive transition register.Program the negative transition register.Query negative transition register.Query condition register.Path to control questionable event registers:Query the event register.Program the enable register.Query the enable register.Program the positive transition register.Query the positive transition register.Program the negative transition register.Query the negative transition register.Query the condition register.Return status registers to default states.Path to access error queue:Query most recent error message.Specify error and status messages for queue.Query enabled messages.Specify messages not to be placed in queue.Query disabled messages.Return to :SYST:PRES defaults.Query revision level of SCPI standard.Query Error Queue.F-3
Page 1 and 2:
®Established 1981Advanced Test Equ
Page 3 and 4:
WARRANTYKeithley Instruments, Inc.
Page 5 and 6:
Manual Print HistoryThe print histo
Page 7 and 8:
If you are using a test fixture, ke
Page 9 and 10:
Table of Contents1 General Informat
Page 11 and 12:
4.10.3 Scanning examples ..........
Page 13:
5.13.4 :FCHannels ................
Page 16 and 17:
List of Illustrations2 Card Install
Page 18 and 19:
6 Theory of OperationFigure 6-1 Mod
Page 20 and 21:
8 MaintenanceTable 8-1Table 8-2Tabl
Page 22 and 23:
General Informationthorized repair
Page 24 and 25:
Card InstallationNOTEIf using the s
Page 26 and 27:
3Getting Started3.1 IntroductionThi
Page 28 and 29:
Getting StartedWARNING: INTERCONNEC
Page 30 and 31:
Getting StartedSLOT 112ROW34COLUMN
Page 32 and 33:
Getting Started3.6 Overview of scan
Page 34 and 35:
Getting Started3.7.2 Close and open
Page 36 and 37:
Getting Started2. If the scan list
Page 38 and 39:
Getting Started3.8 Switching card c
Page 40 and 41:
Getting Started3.9.2 Close and Open
Page 42 and 43:
Getting StartedSCPI (Standard Comma
Page 44 and 45:
Getting Started3.10.5 Abbreviated s
Page 46 and 47:
Getting Started20 OUTPUT 707; “:s
Page 48 and 49:
4Front Panel Operation4.1 Introduct
Page 50 and 51:
Front Panel OperationAnnunciatorsTa
Page 52 and 53:
Front Panel Operation3COLUMNSLOT 1
Page 54 and 55:
Front Panel OperationNot all Model
Page 56 and 57:
Front Panel Operationthe VFD which
Page 58 and 59:
Front Panel OperationFront panel ke
Page 60 and 61:
Front Panel OperationSlot 111 2 3 4
Page 62 and 63:
Front Panel Operation4.8 Channel li
Page 64 and 65:
Front Panel OperationStep 3. Enter
Page 66 and 67:
Front Panel Operationd. Click the I
Page 68 and 69:
Front Panel OperationIdleOPEN ALLId
Page 70 and 71:
Front Panel OperationChannel layerN
Page 72 and 73:
Front Panel Operationsatisfy a chan
Page 74 and 75:
Front Panel OperationExample 3:ARM
Page 76 and 77:
Front Panel Operation6. To store th
Page 78 and 79:
Front Panel Operation8. The INFO ke
Page 80 and 81:
Front Panel Operation4.12.2 GPIBThe
Page 82 and 83:
Front Panel OperationPerform the fo
Page 84 and 85:
Front Panel OperationPlace the curs
Page 86 and 87:
Front Panel OperationThe message in
Page 88 and 89:
Front Panel Operation4.14 Scan conf
Page 90 and 91:
Front Panel OperationTable 4-7 (con
Page 92 and 93:
Front Panel Operationline. Perform
Page 94 and 95:
Front Panel Operation2. To retain t
Page 96 and 97:
Front Panel OperationPerform the fo
Page 98 and 99:
Front Panel Operation4.14.4 Channel
Page 100 and 101:
Front Panel Operation3. Interlocked
Page 102 and 103:
Front Panel OperationPin 7 - Digita
Page 104 and 105:
Front Panel OperationCHANNELREADY4.
Page 106 and 107:
Front Panel OperationFor this test
Page 108 and 109:
Front Panel OperationDUT#11OUTPUTDU
Page 110 and 111:
Front Panel OperationBypass7002Pres
Page 112 and 113:
Front Panel OperationDUT#11OUTPUTHI
Page 114 and 115:
Front Panel Operation7002Press STEP
Page 116 and 117:
Front Panel OperationINOUTTriggerLi
Page 118 and 119:
Front Panel Operationmeter to measu
Page 120 and 121:
5IEEE-488 Reference5.1 Introduction
Page 122 and 123:
IEEE-488 ReferenceIEEE-488Table 5-1
Page 124 and 125:
IEEE-488 ReferenceNOTEController pr
Page 126 and 127:
IEEE-488 ReferenceTriggerTransition
Page 128 and 129:
IEEE-488 ReferenceStandard Event St
Page 130 and 131:
IEEE-488 ReferenceThe filter can be
Page 132 and 133:
IEEE-488 ReferenceArm Condition Reg
Page 134 and 135:
IEEE-488 ReferenceAlwaysZeroLay2Lay
Page 136 and 137:
IEEE-488 ReferenceAlwaysZeroSeq1(B1
Page 138 and 139:
IEEE-488 Reference5.6.6 Questionabl
Page 140 and 141:
IEEE-488 ReferenceReading this regi
Page 142 and 143:
IEEE-488 ReferenceB6 is called the
Page 144:
IEEE-488 Reference:ABORt*RST:SYST:P
Page 147 and 148:
IEEE-488 ReferenceWith the Manual c
Page 149 and 150:
IEEE-488 Reference5.8.2 IFC (interf
Page 151 and 152:
IEEE-488 Reference5-32
Page 153:
IEEE-488 Reference• While ignorin
Page 156 and 157:
IEEE-488 Referenceas command paths.
Page 158 and 159:
IEEE-488 ReferenceResponse messages
Page 160 and 161:
IEEE-488 Reference5.10 Common comma
Page 162 and 163:
IEEE-488 Reference5.10.1 *CLS ⎯ c
Page 164 and 165:
IEEE-488 Referencewhere; CME (bit B
Page 166 and 167:
IEEE-488 Reference5.10.4 *ESR? ⎯
Page 168 and 169:
IEEE-488 Reference5.10.5 *IDN? ⎯
Page 170 and 171:
IEEE-488 ReferenceNOTESee *OPC?, *T
Page 172 and 173:
IEEE-488 ReferenceAfter *OPC? is ex
Page 174 and 175:
IEEE-488 Reference5.10.9 *RCL ⎯ r
Page 176 and 177:
IEEE-488 ReferenceTable 5-5Default
Page 178 and 179:
IEEE-488 Reference5.10.12 *SRE ⎯
Page 180 and 181:
IEEE-488 Reference5.10.13 *SRE? ⎯
Page 182 and 183:
IEEE-488 ReferenceBit 5, Event Summ
Page 184 and 185:
IEEE-488 Reference5.10.16 *TST? ⎯
Page 186 and 187:
IEEE-488 ReferenceLine 70 Wait unti
Page 188 and 189:
IEEE-488 ReferenceSCPI command subs
Page 190 and 191:
IEEE-488 Reference5.11 :DISPlay sub
Page 192 and 193:
:DISPlay subsystemIEEE-488 Referenc
Page 194 and 195:
:DISPlay subsystemIEEE-488 Referenc
Page 196 and 197:
IEEE-488 Reference5.12 :OUTPut subs
Page 198 and 199:
IEEE-488 Reference5.13 [:ROUTe] sub
Page 200 and 201:
[:ROUTe] subsystemIEEE-488 Referenc
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
IEEE-488 Reference5.14 Sense subsys
Page 220 and 221:
IEEE-488 Reference5.15 :SOURce subs
Page 222 and 223:
IEEE-488 Reference5.16 :STATus subs
Page 224 and 225:
:STATus SubsystemIEEE-488 Reference
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
IEEE-488 Reference5.17 :SYSTem subs
Page 248 and 249:
:SYSTem SubsystemIEEE-488 Reference
Page 250 and 251:
IEEE-488 Reference5.18 Trigger subs
Page 252 and 253:
Trigger subsystemIEEE-488 Reference
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
6Theory of Operation6.1 Introductio
Page 268 and 269:
Theory of Operation6.3 Control func
Page 270 and 271:
Theory of Operation6.4 Relay contro
Page 272 and 273:
Theory of OperationID data is conta
Page 274 and 275:
Theory of OperationFromDigitalBoard
Page 276 and 277:
Theory of Operationµ DINConnectorT
Page 278 and 279:
MaintenanceNOTEThe digital and disp
Page 280 and 281:
MaintenanceFuse replacement procedu
Page 282 and 283:
Maintenance7.6 Instrument disassemb
Page 284 and 285:
Maintenance7.6.5 Power supplies rem
Page 286 and 287:
Maintenance8. Press “1”, “1
Page 288 and 289:
MaintenanceEDIT ERR REM TALK LSTN S
Page 290 and 291:
MaintenanceTo review the error, pre
Page 292 and 293:
MaintenanceTrigger 8 (STI8) is set
Page 294 and 295:
MaintenanceDETAIL AREF:GRN/YELWIRE#
Page 296 and 297:
MaintenanceBOARDS MUST BE HANDLED W
Page 298 and 299:
MaintenanceSTEP 1FA-151-1, FASTENER
Page 300 and 301:
MaintenanceDETAIL ACC-47, CABLEDIG
Page 302 and 303:
Maintenance8#4-40x1/4"PFH(4 REQ'D)(
Page 304 and 305:
Replaceable Parts
Page 306 and 307:
Replaceable Parts
Page 311 and 312: Replaceable PartsTable 8-2Digital b
Page 313 and 314: Artisan Scientific - Quality Instru
Page 315: (+5V)**(+5V)**** ****** **********
Page 318 and 319: Replaceable PartsTable 8-3VFD displ
Page 322 and 323: Replaceable PartsTable 8-4Backplane
Page 324: Artisan Scientific - Quality Instru
Page 327 and 328: Replaceable Parts
Page 331 and 332: Replaceable PartsTable 8-6Miscellan
Page 333 and 334: Interface Function CodesTable A-1Mo
Page 335 and 336: Controller ProgramsIBM PC/XT/AT wit
Page 337 and 338: Controller Programs10 DEF SEG=&HC40
Page 339 and 340: Controller ProgramsHewlett-Packard
Page 341 and 342: Controller ProgramsBUS.INIT\ Initia
Page 343 and 344: CASCII Character Codesand IEEE-488
Page 345 and 346: ASCII Character Codes and IEEE-488M
Page 347 and 348: IEEE-488 Bus Overviewtype of instru
Page 349 and 350: IEEE-488 Bus Overviewdevice will re
Page 351 and 352: IEEE-488 Bus OverviewLAG (Listen Ad
Page 353 and 354: IEEE-488 Bus OverviewTable D-2Hexad
Page 355 and 356: EIEEE-488 Conformance InformationIn
Page 357: FSCPI Conformance InformationIntrod
Page 361 and 362: SCPI Conformance InformationTable F
Page 363 and 364: SCPI Conformance InformationTable F
Page 365 and 366: IEEE-488.2 Common CommandsMnemonic
Page 367 and 368: SCPI Command SubsystemTable H-1DISP
Page 369 and 370: SCPI Command SubsystemTable H-4SENS
Page 371 and 372: SCPI Command SubsystemTable H-6 (co
Page 373 and 374: SCPI Command SubsystemTable H-8 (co
Page 375 and 376: QuickBasic and QuickC ProgramsMicro
Page 377 and 378: QuickBasic and QuickC ProgramsMicro
Page 379 and 380: Index:ABORt 5-134:BBMake 5-88:CLOS
Page 381 and 382: Scanning channels 4-20Scanning exam
Page 383: Specifications are subject to chang
show all

Model 7002Switch System Instruction Manual - Advanced Test ...

Create successful ePaper yourself

Delete template?

Save as template?