Model 7002Switch System Instruction Manual - Advanced Test ...

Index:ABORt 5-134:BBMake 5-88:CLOSe 5-80:CONDition? 5-122:COUNt 5-135:CPAirX where; X=[1] to 5 5-89:CTYPe 5-91:DELay 5-137:DISPlay subsystem 5-71:ENABle 5-109:ERRor? 5-129[:EVENt]? 5-104:FCHannels 5-85:IMMediate 5-134:INTerlock:LIST Commands 5-86:INITiate commands 5-133:NTRansition 5-120:OPEN \|ALL 5-82:OUTPut subsystem 5-77:PREset 5-123, 5-127:POLE 5-92:POSetup 5-127:PTRansition 5-113:QUEue commands 5-124:RECall M,NRf> 5-98[:ROUTe] subsystem 5-79:SAVE:LIST , M 5-96:SAVE[:RELays] M 5-96:SCAN 5-83:SCLHannel 5-88:SIGNal 5-141:SOURce subsystem 5-101:SOURce 5-138:STATus subsystem 5-103:STIMEe 5-94:SYSTem subsystem 5-127:TIMer 5-140:VERsion? 5-128Symbols#-OF-POLES 4-39*CLS ⎯ clear status 5-43*ESE ⎯ event status enable 5-44*ESE? ⎯ event status enable query 5-46*ESR? ⎯ event status register query 5-47*IDN? ⎯ identification query 5-49*OPC ⎯ operation complete 5-50*OPC? ⎯ operation complete query 5-52*OPT? ⎯ option identification query 5-54*RCL ⎯ recall 5-55*RST ⎯ reset 5-56*SAV ⎯ save 5-58*SRE ⎯ service request enable 5-59*SRE? ⎯ service request enable query5-61*STB? ⎯ status byte query 5-62*TRG ⎯ trigger 5-64*TST? ⎯ self-test query 5-65*WAI ⎯ wait-to-continue 5-66AAbbreviated common command summary3-17Abbreviated SCPI command summary3-18Abbreviated syntax rules 3-19Address decoding 6-3Analog backplane 4-5ARM CONTROL 4-48Arm event status 5-12ASCII character codes and IEEE-488 multilineinterface commandmessages C-1Asynchronous trigger link 4-60BBackplane boards 7-17Backplane boards removal 7-8Backplane interface 6-5Bottom cover removal 7-7Built-in-tests 7-10, 7-13Bus connections 3-17CCard configuration 4-37Card installation 2-1CARD PAIR 4-39Card type 3-13CHAN-CONTROL 4-43Changing firmware 7-5Changing the battery 7-4Changing the display mode 4-10Changing the display mode (keypadmethod) 3-5Changing the display mode (light penmethod) 3-5Channel assignments 3-5, 4-12Channel list and scan list 4-15Channel patterns 4-27Channel ready 4-57Channel restrictions 4-51Close and open channels 3-9, 3-15Closing and opening channels 4-19Common commands 5-41Component layout and schematic diagrams8-1Control function 6-3Controller programming 5-4Controller programs B-1Controlling digital circuitry 4-54Create channel list and/or scan list 3-14DDCL (device clear) 5-30DELAY 4-40Diagnostics 7-9Digital board 7-16Digital board removal 7-8Digital I/O port 4-53Digital input channel 4-56DIGITAL-I/O 4-33Display boards 7-16Display boards removal 7-9Display modes 3-3, 4-8Display test — char set 7-13Display test — LED board 7-12i-1