OPERATION MANUAL - Scintrex

More documents

Recommendations

Info

Setting Up Your InstrumentPRESSF5Press the F5 keys. The followingscreen is displayed.PRESSF3Press the F3 key to choose theEDIT mode.The baud rate parameter is highlighted as illustratedbelow. It is the only parameter that can be edited onthis screen:Baud Rate:Press the right or left arrows to select one of thepredefined baud rates. Allowed values are 600,1200, 2400, 4800, 9800, 19200, 38400 and 57600.PRESSF5When you have selected the correct rate for yourpersonal computer, press the F5 key.2-26CG-5 Manual - part # 867700 Revision 2
Using the Dump ScreenStarting a DumpAn instrument dump is also initiated from theDUMP PARAMETER SETUP screen. For moredetails, see “Dumping Data using the RS-232CPort” on page 3-38.Setup2-27CG-5 Manual - part # 867700 Revision 2
Page 1 and 2:
CG-5Scintrex Autograv SystemOPERATI
Page 3:
CG-5Scintrex Autograv SysemOperatio
Page 6:
Entering Alphanumerics, Example 1 .
Page 9 and 10:
Understanding Life Expectancy . . .
Page 11 and 12:
Appendix C: Elastic Hysteresis Effe
Page 13 and 14:
ForewordForewordCongratulations on
Page 15 and 16:
Data Dump ConnectorsThe system is e
Page 17 and 18:
• *.SGD (Scintrex proprietary for
Page 19 and 20:
1 GettingStartedStartupAbout this M
Page 21 and 22:
About this ManualChapter LayoutThis
Page 23 and 24:
Understanding Instrument BasicsUnde
Page 25 and 26:
Understanding Instrument BasicsLoca
Page 27 and 28:
Understanding Instrument BasicsThe
Page 29 and 30: Understanding Instrument BasicsUsin
Page 31 and 32: Understanding Instrument BasicsPRES
Page 33 and 34: Understanding Instrument BasicsNavi
Page 35 and 36: Understanding Instrument BasicsHELP
Page 37 and 38: Understanding Instrument Basicsor b
Page 41 and 42: Understanding Instrument BasicsEnte
Page 43 and 44: Understanding Instrument BasicsIn t
Page 47 and 48: Understanding Instrument BasicsAcce
Page 49 and 50: Initializing Instrument ParametersU
Page 55 and 56: 2 Setting UpYourInstrumentSetupBefo
Page 57 and 58: Using the Survey ScreenUsing the Su
Page 59 and 60: Using the Survey ScreenIf you are u
Page 61 and 62: Using the Survey ScreenSpecifying G
Page 63 and 64: Using the Survey ScreenPRESSF1Press
Page 65 and 66: Using the Autograv ScreenUsing the
Page 67 and 68: Using the Autograv ScreenUse the le
Page 69 and 70: Using the Autograv ScreenPRESSF3Pre
Page 71 and 72: Using the Autograv ScreenDrift:Long
Page 73 and 74: Using the Options ScreenDefining Re
Page 75 and 76: Using the Options ScreenStart Delay
Page 77 and 78: Using the Clock ScreenPRESSF5Press
Page 79: Using the Dump ScreenUsing the Dump
Page 83 and 84: Using the Memory ScreenPRESSF5Press
Page 85 and 86: Using the Service ScreenUsing the S
Page 87 and 88: SetupUsing the Service ScreenThe ph
Page 89 and 90: Using the Service ScreenEnable Fact
Page 91 and 92: 3 Operating theCG-5 in theFieldBy n
Page 93 and 94: Initializing Field ParametersSettin
Page 95 and 96: Initializing Field ParametersType t
Page 97 and 98: Initializing Field ParametersEditin
Page 99 and 100: Initializing Field ParametersThe se
Page 101 and 102: Setting Up the TripodSetting up the
Page 103 and 104: Setting Up the TripodNote:Terrain c
Page 105 and 106: Setting Up the TripodPress the F1
Page 107 and 108: Performing Data AcquisitionFigure 5
Page 109 and 110: Performing Data AcquisitionReviewin
Page 111 and 112: Performing Data AcquisitionTaking a
Page 113 and 114: Performing Data Acquisitioncolumn.
Page 115 and 116: Entering NotesEntering NotesDuring
Page 117 and 118: Entering NotesThe following screen
Page 119 and 120: Entering NotesRecording Notes Using
Page 121 and 122: Entering NotesUsing your macros —
Page 123 and 124: Recalling DataRecalling DataDuring
Page 125 and 126: Recalling DataPRESSF1To display the
Page 127 and 128: Recalling DataRecalling Line DataPR
Page 129 and 130: Dumping DataNote:Your version of SC
Page 131 and 132:
Dumping Data• *.sgd. The Scintrex
Page 133 and 134:
Dumping Datacolumn 2TiltX=((TILTX_S
Page 135 and 136:
Dumping DataSetting Communication P
Page 137 and 138:
Dumping DataSetting Communication P
Page 139 and 140:
Dumping DataYou will then be prompt
Page 141 and 142:
Dumping DataPRESSF5After you have t
Page 143 and 144:
Dumping DataDumping Data with the U
Page 145 and 146:
Dumping DataIn the Dump window of t
Page 147 and 148:
Reprogramming your CG-5Reprogrammin
Page 149 and 150:
Reprogramming your CG-5The followin
Page 151 and 152:
Reprogramming your CG-5Press the ar
Page 153 and 154:
Clearing MemoryClearing MemoryYou c
Page 155 and 156:
4 Optimizingyour FieldOperationsIn
Page 157 and 158:
material and fasten it down with a
Page 159 and 160:
Selecting Base StationsRepeated gra
Page 161 and 162:
5Maintaining YourCG-5 andTrouble-sh
Page 163 and 164:
Using the Smart BatteryUnderstandin
Page 165 and 166:
Using the Smart BatteryReplacing a
Page 167 and 168:
Using the Power AdapterCharging Not
Page 169 and 170:
Using the external battery beltConn
Page 171 and 172:
Adjusting Instrument ParametersObta
Page 173 and 174:
Adjusting Instrument ParametersPRES
Page 175 and 176:
Adjusting Instrument Parameterswher
Page 177 and 178:
Applying Tilt CorrectionsApplying T
Page 179 and 180:
Applying Tilt CorrectionsPRESSF3Pre
Page 181 and 182:
Applying Tilt CorrectionsPRESSENTER
Page 183 and 184:
Applying Tilt CorrectionsPRESSF1The
Page 185 and 186:
Applying Tilt CorrectionsPRESSF5In
Page 187 and 188:
MaintenanceApplying Tilt Correction
Page 189 and 190:
Adjusting Tilt Sensor Cross- Coupli
Page 191 and 192:
Adjusting Tilt Sensor Cross- Coupli
Page 193 and 194:
Re-Calibrating the CG-5greatest pre
Page 195 and 196:
Trouble-shootingTrouble-shootingDes
Page 197 and 198:
Trouble-shooting your USB portTroub
Page 199 and 200:
Warranty and RepairShipping Instruc
Page 201 and 202:
6 ReferenceInformationReferenceThis
Page 203 and 204:
General SpecificationsHardware Spec
Page 205 and 206:
General SpecificationsData StorageS
Page 207 and 208:
General SpecificationsStandard Acce
Page 209 and 210:
Instrument Parts ListInstrument Par
Page 211 and 212:
ARemoteOperation ofthe CG-5For oper
Page 213 and 214:
PRESSF5Press the F5 key. The follo
Page 215 and 216:
RemoteEnter your name and the name
Page 217 and 218:
RemoteDefine a folder name for addi
Page 219 and 220:
This is the main screen used for op
Page 221 and 222:
You are now ready to configure the
Page 223 and 224:
RemoteSelect any corrections that y
Page 225 and 226:
To exit and save your settings, pre
Page 227 and 228:
Measuring DataThe data measuring pr
Page 229 and 230:
To stop measurement, press the Stop
Page 231 and 232:
Dumping DataTo dump data from the C
Page 233 and 234:
To exit from the Memory option, pre
Page 235 and 236:
BTheory ofOperationSystem OverviewT
Page 237 and 238:
TEMPERATURE CONTROLLEDVACUUM CHAMBE
Page 239 and 240:
• the system applies a self-calib
Page 241 and 242:
Example: —Because of the positive
Page 243 and 244:
If, after many years of service, yo
Page 245 and 246:
The formula given in Equation (B.8)
Page 247 and 248:
which occur during the first 5 seco
Page 249 and 250:
measurements were recorded with the
Page 251 and 252:
Compensation and CorrectionsTo elim
Page 253 and 254:
Compensation and Correctionssample
Page 255 and 256:
Compensation and Corrections(16% in
Page 257 and 258:
CElasticHysteresisEffectsAll spring
Page 259 and 260:
In the case of the CG-5, where the
Page 261 and 262:
DScintrex UtilitiesProgramSCTUTILTh
Page 263 and 264:
Installing SCTUTILAfter the Install
Page 265 and 266:
Installing SCTUTILThe following scr
Page 267 and 268:
Installing SCTUTILThe following scr
Page 269 and 270:
Installing your USB driverInstallin
Page 271 and 272:
Installing your USB driver3. Insert
Page 273 and 274:
Installing your USB driver5.Press t
Page 275 and 276:
Installing your USB driverInstallin
Page 277 and 278:
Installing your USB driver3. Select
Page 279 and 280:
Installing your USB driver7. Click
Page 281 and 282:
Installing your USB driver2. Select
Page 283 and 284:
Installing your USB driver5.Click
Page 285 and 286:
Installing your USB driver7. Click
Page 287 and 288:
ECG-5 MenuMapsMenu MapsThis chapter
Page 289 and 290:
Setup Menu MapsSetup Menu MapsSurve
Page 291 and 292:
Setup Menu MapsDump and Service Men
Page 293 and 294:
Measurement Menu MapsTilt Sensitivi
Page 295 and 296:
Other Menu MapsInfo MenuINFOINFO /
Page 297 and 298:
IndexNumerics1/ABC Key 1-162/DEF Ke
Page 299 and 300:
manual method 5-13software method 5
Page 301 and 302:
UTM Zone 2-7RRECALL/5/MNO Key 1-16R
Page 303:
Head Office222 Snidercroft RoadConc
show all

OPERATION MANUAL - Scintrex

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?