Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Network menu<br />
This menu lets you configure the network interface installed in your<br />
printer. You can reset the network interface and print a configuration<br />
page.<br />
Item<br />
Clear<br />
Setting<br />
Explanation<br />
This item performs a simple reset and restores the<br />
factory default settings for the network<br />
configuration. This setting will only take effect after<br />
you have reset the printer.<br />
Item<br />
TCP/IP<br />
Explanation<br />
Values: DHCP, BOOTP, Static<br />
Network<br />
Info<br />
This item print a page showing the network<br />
parameters you set.<br />
EtherTalk<br />
NetWare<br />
Ethernet<br />
Speed<br />
Wireless<br />
This item allows you to manually set the TCP/IP<br />
addresses or receive the addresses from the<br />
network.<br />
• DHCP: The DHCP server allots the IP address to<br />
you automatically.<br />
• BOOTP: The BOOTP server allots the IP address<br />
to you automatically.<br />
• Static: You can enter IP address, subnet mask,<br />
and gateway manually.<br />
Values: Off, On<br />
This item lets you select whether or not you use the<br />
EtherTalk protocol. Select On to use the protocol.<br />
Values: Auto, 802.2, 802.3, Ethernet II, SNAP, Off<br />
This item lets you select the IPX frame type.<br />
• Auto: You can set the frame type automatically.<br />
• 802.2: Select this value to use the IEEE 802.2<br />
frame type.<br />
• 802.3: Select this value to use the IEEE 802.3<br />
frame type.<br />
• Ethernet II: Select this value to use the Ethernet 2<br />
frame type.<br />
• SNAP: Select this value to use the SNAP frame<br />
type.<br />
• Off: You can disable the NetWare protocol.<br />
Values: Auto, 10M Half, 10M Full,<br />
100M Half, 100M Full<br />
This item allows you to select the ethernet speed.<br />
Values: WLAN Basic, WLAN Security, WLAN Default<br />
Configure the wireless network environments.<br />
See page 10.3.<br />
Note<br />
This menu only appears when an optional<br />
wireless network interface card has been<br />
installed.<br />
Printing a demo page<br />
Print a demo page to make sure that the printer is operating correctly.<br />
<strong>ML</strong>-3050, <strong>ML</strong>-<strong>3051N</strong><br />
Press and hold Demo for about 2 seconds.<br />
<strong>ML</strong>-<strong>3051N</strong>, <strong>ML</strong>-<strong>3051N</strong>D<br />
1 Press Menu and then OK when Information appears.<br />
2 Press the Scroll buttons until Demo Page appears and press OK.<br />
A demo page prints out.<br />
Changing the display language (<strong>ML</strong>-<strong>3051N</strong>, <strong>ML</strong>-<br />
<strong>3051N</strong>D only)<br />
To change the language that is displayed on the control panel, follow<br />
these steps:<br />
1 Press Menu until System Setup appears on the bottom line of the<br />
display and press OK.<br />
2 Press OK when Language appears.<br />
3 Press the Scroll buttons to select the language you want and press<br />
OK.<br />
4 Press Stop to return to Standby mode.<br />
2.6