Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Samsung ML-3051N - User Manual_9.08 MB, pdf, ENGLISH
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Understanding display messages<br />
Message Meaning Suggested solutions<br />
Messages appear on the Smart Panel program window or the control<br />
panel display to indicate the printer’s status or errors. Refer to the tables<br />
below to understand the messages’ meaning and correct the problem if<br />
necessary. Messages and their meanings are listed in alphabetical<br />
order.<br />
Note<br />
When you call for service, it is very convenient to tell the<br />
service representative the display message.<br />
Message Meaning Suggested solutions<br />
Door Open<br />
Duplex Jam 0<br />
Check Inside<br />
Duplex Jam 1 Open/<br />
Close Door<br />
Fuser Door Open<br />
Load <strong>Manual</strong>ly<br />
Press Stop Key<br />
Low Heat Error<br />
Cycle Power<br />
LSU Hsync Error<br />
Cycle Power<br />
LSU Motor Error<br />
Cycle Power<br />
The front cover or<br />
rear cover is not<br />
securely latched.<br />
Paper has jammed<br />
during duplex<br />
printing.<br />
Paper has jammed<br />
during duplex<br />
printing.<br />
The fuser door is<br />
not securely latched.<br />
The multi-purpose<br />
tray is empty in<br />
manual feed mode.<br />
There is a problem<br />
in the fuser unit.<br />
A problem has<br />
occurred in the LSU<br />
(Laser Scanning<br />
Unit).<br />
A problem has<br />
occurred in the LSU<br />
(Laser Scanning<br />
Unit).<br />
Close the cover until<br />
it locks into place.<br />
Clear the jam. See<br />
page 9.4.<br />
Clear the jam. See<br />
page 9.5.<br />
Open the rear cover<br />
and close the fuser<br />
door until it locks into<br />
place.<br />
For the location of<br />
the fuser door, see<br />
page 9.4.<br />
Load a sheet of print<br />
material and press<br />
Stop.<br />
Unplug the power<br />
cord and plug it back<br />
in. If the problem<br />
persists, please call<br />
for service.<br />
Unplug the power<br />
cord and plug it back<br />
inches. If the<br />
problem persists,<br />
please call for<br />
service.<br />
Unplug the power<br />
cord and plug it back<br />
inches. If the<br />
problem persists,<br />
please call for<br />
service.<br />
Main Motor Locked<br />
Open Heat Error<br />
Cycle Power<br />
Over Heat Error<br />
Cycle Power<br />
Paper Jam 0<br />
Open/Close Door<br />
Paper Jam 1<br />
Open/Close Door<br />
Paper Jam 2<br />
Check Inside<br />
Printing...<br />
Ready<br />
Self Diagnostic...<br />
Sleeping...<br />
Tray 1<br />
Paper Empty<br />
Tray 2<br />
Paper Empty<br />
There is a problem<br />
in the main motor.<br />
There is a problem<br />
in the fuser unit.<br />
There is a problem<br />
in the fuser unit.<br />
Paper has jammed<br />
in the feeding area<br />
of the tray.<br />
Paper has jammed<br />
in the fuser area.<br />
Paper has jammed<br />
in the paper exit<br />
area.<br />
The printer is<br />
printing jobs using<br />
the displayed<br />
language.<br />
The printer is on-line<br />
and ready to printer.<br />
The engine in your<br />
printer is checking<br />
some problems<br />
detected.<br />
The printer is on<br />
power save mode.<br />
There is no paper in<br />
the tray 1.<br />
There is no paper in<br />
the optional tray 2.<br />
Open and then close<br />
the front cover.<br />
Unplug the power<br />
cord and plug it back<br />
in. If the problem<br />
persists, please call<br />
for service.<br />
Unplug the power<br />
cord and plug it back<br />
in. If the problem<br />
persists, please call<br />
for service.<br />
Clear the jam. See<br />
page 9.1 and<br />
page 9.1.<br />
Clear the jam. See<br />
page 9.3.<br />
Clear the jam. See<br />
page 9.3.<br />
Complete your<br />
printing.<br />
Use your printer.<br />
Please wait a few<br />
minutes.<br />
When data is<br />
received, it switches<br />
to on-line<br />
automatically.<br />
Load paper in the<br />
tray 1. See page 5.5.<br />
Load paper in the<br />
optional tray 2. See<br />
page 5.5.<br />
9.7
Change language