service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Main Sub<br />
code code<br />
66 13 Dial test (Executable only<br />
when the FAX is installed.)<br />
Contents Details of function/operation<br />
17 DTMF signal send (Max.<br />
value) (Executable only<br />
when the FAX is installed.)<br />
[Function]<br />
Use to the dial test.<br />
[Operation]<br />
■ Dial test (PULSE)<br />
1) Initial display<br />
SELECT SIGNAL<br />
1:PULSE 2:DTMF<br />
∗ [Cle<strong>ar</strong>] key: FAX control is<br />
terminated.<br />
2) Select 1<br />
INPUT MAKE TIME<br />
(0-15) __<br />
3) Enter the make time in 2 digits.<br />
INPUT DIAL #<br />
XXXX<br />
XXXX: Default<br />
∗ After deleting with [Cle<strong>ar</strong>] key, input<br />
can be made.<br />
4) [OK]/[ENTER] key<br />
SEND yyPPS xxms<br />
1:YES 2:NO<br />
"yy" is the selected pulse 10 or 20.<br />
"xx" is the input value.<br />
∗ Select 2: Returns to “2)” display.<br />
5) Select 1<br />
Switched to 10/20PPS set with<br />
pulse selection inside.<br />
6) After setting<br />
SENDING yyPPS xxms<br />
7) After completion of sending<br />
TERMINATE ?<br />
1:YES 2:NO<br />
∗ Select 2: Returns to “4)” display.<br />
8) Select 1<br />
TERMINATED<br />
After 2sec, returns to "1) Initial display".<br />
[Function]<br />
Use to set the DTMF signal send (Max. value).<br />
[Operation]<br />
1) Initial display<br />
INPUT DIAL #<br />
∗ [Cle<strong>ar</strong>] key: FAX control is terminated.<br />
2) [Numeric] key input<br />
The content selected with signal send<br />
level selection is set inside.<br />
■ Dial test (DTMF)<br />
1) Initial display<br />
SELECT SIGNAL<br />
1:PULSE 2:DTMF<br />
AR-203E/<strong>5420</strong>/M200/M201 SIMULATION, TROUBLE CODES 10 - 37<br />
∗ [Cle<strong>ar</strong>] key: FAX control is terminated.<br />
2) Select 2<br />
SELECT HIGH LEVEL<br />
1:DEFAULT 2:SOFT SW.<br />
↓<br />
3) Select 1 ↓<br />
SELECT LOW LEVEL<br />
1:DEFAULT 2:SOFT SW.<br />
↓<br />
4) Select 1 ↓<br />
INPUT DIAL #<br />
XXXX<br />
↓ Select 2<br />
INPUT VALUE<br />
(0-15) __<br />
↓ Select 2<br />
INPUT VALUE<br />
(0-15) __<br />
XXXX: Default<br />
∗ After deleting with [Cle<strong>ar</strong>] key, input can be<br />
made.<br />
4) [OK]/[ENTER] key<br />
H:xx L:yy<br />
1:YES 2:NO<br />
"xx" indicates HI, and "yy" indicates Low Soft SW.<br />
∗ Select 2: Returns to “4)” display.<br />
5) Select 1<br />
HI/LO is selected with the signal level inside.<br />
6) After setting the signal send level<br />
SENDING DTMF<br />
7) After completion of sending<br />
TERMINATE ?<br />
1:YES 2:NO<br />
∗ Select 2: Returns to “4)” display.<br />
8) Select 1<br />
TERMINATED<br />
After 2sec, returns to "1) Initial display".<br />
3) Communication is st<strong>ar</strong>ted after setting the<br />
signal send level.<br />
SENDING SIGNAL MAX<br />
PRESS CLEAR TO STOP<br />
∗ [Cle<strong>ar</strong>] key: Returns to "1) Initial display".
Change language