service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Main<br />
code<br />
Sub<br />
code<br />
Contents Details of function/operation<br />
08 01 Developing bias [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the developing bias signal is turned ON for 30sec.<br />
When, however, an actual output value is measured, use simulation 25-01.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation] (AR-M200/M201)<br />
02 Main ch<strong>ar</strong>ger (Grid high) [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the main ch<strong>ar</strong>ger is outputted for 30sec in the grid<br />
voltage HIGH move.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation] (AR-M200/M201)<br />
1) Initial display<br />
08-02 MHV(H) SET.<br />
EXECUTING...<br />
03 Grid voltage (Low) [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the main ch<strong>ar</strong>ger is outputted for 30sec in the grid<br />
voltage LOW move.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation] (AR-M200/M201)<br />
1) Initial display<br />
08-03 MHV(L) SET.<br />
EXECUTING...<br />
06 Transfer ch<strong>ar</strong>ger [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the transfer ch<strong>ar</strong>ger is outputted for 30sec.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation] (AR-M200/M201)<br />
1) Initial display<br />
08-06 THV SET.<br />
EXECUTING...<br />
09 01 Duplex motor normal<br />
rotation operation check<br />
(AR-M201 only)<br />
02 Duplex motor reverse<br />
operation check<br />
(AR-M201 only)<br />
04 Duplex motor rotation speed<br />
adjustment (AR-M201 only)<br />
1) Initial display<br />
08-01 DVLP BIAS SET.<br />
EXECUTING...<br />
[Function]<br />
Use the duplex motor Bios to drive the duplex motor in the normal direction (paper exit direction)<br />
for 30sec.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation]<br />
1) Initial display<br />
09-01 DPLX ROT.<br />
EXECUTING...<br />
[Function]<br />
Use the duplex motor Bios to drive the duplex motor in the reverse direction for 30sec.<br />
After completion of this process, the machine goes into the sub code entry standby mode.<br />
[Operation]<br />
1) Initial display<br />
09-02 DPLX ROT.REV.<br />
EXECUTING...<br />
[Function]<br />
When this simulation is executed, the currently set value is displayed.<br />
Enter the adjustment value with [Numeric] key and press [OK]/[ENTER]/[START] key. The<br />
entered value is stored and the machine goes into the sub code entry standby mode. The<br />
greater the set value is, the higher the speed is. The smaller the set value is, the lower the<br />
speed is. (Setting range: 1 - 13, Default: 8)<br />
[Operation]<br />
1) Initial display 2) [Numeric] key 3) [OK]/[ENTER]/[START]<br />
09-04 DPLX ROT.SPEED<br />
8( 1-13)<br />
AR-203E/<strong>5420</strong>/M200/M201 SIMULATION, TROUBLE CODES 10 - 7<br />
09-04 DPLX ROT.SPEED<br />
key<br />
7( 1-13) 09-04 DPLX ROT.SPEED<br />
7( 1-13)
Change language