service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Main Sub<br />
code code<br />
66 18 DTMF signal send (Soft SW<br />
set value) (Executable only<br />
when the FAX is installed.)<br />
Contents Details of function/operation<br />
21 FAX information print<br />
(Executable only when the<br />
FAX is installed.)<br />
24 FAST SRAM cle<strong>ar</strong><br />
(Executable only when the<br />
FAX is installed.)<br />
30 TEL/LIU status change<br />
check (Executable only<br />
when the FAX is installed.)<br />
[Function]<br />
Use to set the DTMF signal send (Soft SW set value).<br />
[Operation]<br />
1) Initial display<br />
3) Communication is st<strong>ar</strong>ted after setting the<br />
INPUT DIAL #<br />
signal send level.<br />
SENDING SIGNAL SSW<br />
∗ [Cle<strong>ar</strong>] key: FAX control is terminated. PRESS CLEAR TO STOP<br />
2) [Numeric] key input<br />
The content selected with signal send<br />
level selection is set inside.<br />
∗ [Cle<strong>ar</strong>] key: Returns to "1) Initial display".<br />
[Function]<br />
Use to print the FAX information.<br />
[Operation]<br />
1) Initial display<br />
SELECT REPORT (1-3)<br />
PRESS ←, →<br />
2) [ ] [ ] key or after 2sec<br />
Every time when [<br />
→ 3 → 1.<br />
] key is pressed, the second line is changed in the sequence of 1 → 2<br />
When [ ] key is pressed, the sequence is reversed.<br />
SELECT REPORT (1-3)<br />
1:USER SW. LIST<br />
∗ [Cle<strong>ar</strong>] key: FAX control is terminated.<br />
3) [OK]/[ENTER] key<br />
When print is allowed When print is inhibited<br />
PRINT STORED CAN NOT PRINT<br />
After completion of printing,<br />
FAX control is terminated.<br />
[Function]<br />
Use to cle<strong>ar</strong> the FAST SRAM.<br />
[Operation]<br />
1) Initial display 2) After completion of cle<strong>ar</strong>ing<br />
[Function]<br />
Use to check the TEL/LIU status change.<br />
[Operation]<br />
SELECT REPORT (1-3)<br />
2:SOFT SW. LIST<br />
After 2sec, FAX control is<br />
terminated.<br />
CLEAR FAST SRAM CLEARED<br />
1) Initial display<br />
HS2 :xxx HS1 :xxx<br />
RHS :xxx EXHS:xxx<br />
↑<br />
The display is switched every 2sec.<br />
↓<br />
CHECKING<br />
PRESS CLEAR TO STOP<br />
∗ [Cle<strong>ar</strong>] key: FAX control is terminated.<br />
After 2sec, FAX control is terminated.<br />
AR-203E/<strong>5420</strong>/M200/M201 SIMULATION, TROUBLE CODES 10 - 38<br />
SELECT REPORT (1-3)<br />
3:PROTOCOL