service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
service manual ar-203e ar-203e x ar-m200 ar-m201 model ar-5420
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
4. Descriptions of v<strong>ar</strong>ious simulations<br />
Main<br />
code<br />
Sub<br />
code<br />
Contents Details of function/operation<br />
01 01 Mirror scan operation [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the home position is checked and the mirror base<br />
performs full scan at the speed of the set magnification ratio.<br />
During operation, the set magnification ratio is displayed.<br />
The mirror home position sensor status is displayed with the "Drum replacement required lamp<br />
(or the copy mode indicator for the AR-M200/M201)". (When the mirror is in the home position,<br />
the lamp lights up.)<br />
During operation, the copy lamp lights up.<br />
When [Cle<strong>ar</strong>] key is pressed, if the operation is on the way, it is terminated and the machine<br />
goes to the sub code entry standby mode.<br />
[Operation] (AR-M200/M201)<br />
1) Initial display 2) [ZOOM]/[COPY RATIO] 3) [OK]/[ENTER]/[START]<br />
01-01 SCAN CHK<br />
key<br />
key<br />
- 100% + 01-01 SCAN CHK<br />
01-01 SCAN CHK<br />
- 78% + EXECUTING... - 78% +<br />
02 Mirror home position sensor<br />
(MHPS) status display<br />
[Function]<br />
Monitors the mirror home position sensor, and makes the "Drum replacement required lamp (or<br />
the copy mode indicator for the AR-M200/M201)" turn on during the sensor ON status.<br />
[Operation] (AR-M200/M201)<br />
1) Initial display<br />
06 Aging of mirror scanning [Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the mirror base performs full scan at the speed of<br />
the set magnification ratio.<br />
During operation, the set magnification ratio is displayed.<br />
After 3sec, the mirror base performs full scan again.<br />
∗ When [OK]/[ENTER]/[START] key is pressed once, the ready lamp remains OFF.<br />
The mirror home position sensor status is displayed on the "Drum replacement required lamp<br />
(or the copy mode indicator for the AR-M200/M201)." (The lamp is ON when the mirror is in the<br />
home position.)<br />
During aging, the copy lamp is ON.<br />
[Operation] (AR-M200/M201)<br />
The operation is simil<strong>ar</strong> to simulation 01-01.<br />
02 01 SPF/RSPF aging operation<br />
(Only the AR-203E/M200/<br />
M201 with the SPF/RSPF<br />
installed)<br />
01-02 MHP-SENSOR<br />
EXECUTING...<br />
2) [ ] key<br />
01-01 SCAN CHK<br />
- 99% +<br />
2) [ ] key<br />
01-01 SCAN CHK<br />
- 101% +<br />
[Function]<br />
When [OK]/[ENTER]/[START] key is pressed, the set magnification ratio is obtained. For the<br />
SPF, the single-face document transport is performed. For the RSPF, the duplex document<br />
transport is performed.<br />
However, the operating conditions don't matter and the operation is not stopped even in case of<br />
a jam. Also the magnification ratio is displayed on the LCD/display.<br />
[Operation] (AR-M200/M201)<br />
The operation is simil<strong>ar</strong> to simulation 01-01.<br />
AR-203E/<strong>5420</strong>/M200/M201 SIMULATION, TROUBLE CODES 10 - 3