Project Manual 11-210C - Ramapo College of New Jersey

More documents

Recommendations

Info

SECTION 01 33 00 – SUBMITTAL PROCEDURES 5. Maintain sets of Samples, as returned, at the Project site, for quality comparisons throughout the course of construction. a. Unless noncompliance with Contract Document provisions is observed, the submittal may serve as the final submittal. b. Sample sets may be used to obtain final acceptance of the construction associated with each set. B. Distribution of Samples: Prepare and distribute additional sets to subcontractors, manufacturers, fabricators, suppliers, installers, and others as required for performance of the Work. Show distribution on transmittal forms. 1. Field Samples specified in individual Sections are special types of Samples. Field Samples are full-size examples erected on site to illustrate finishes, coatings, or finish materials and to establish the standard by which the Work will be judged. a. Comply with submittal requirements to the fullest extent possible. Process transmittal forms to provide a record of activity. 1.7 ARCHITECT'S ACTION A. Except for submittals for record, information or similar purposes, where action and return is required or requested, the Architect will review each submittal, mark to indicate action taken, and return provided the submittal is in accordance with the contract documents. 1. Compliance with specified characteristics is the Contractor's responsibility. B. Action Stamp: The Architect will stamp each submittal with a uniform, self-explanatory action stamp. C. Unsolicited Submittals: Unsolicited Submittals and Submittals not required by the Contract Documents may not be reviewed, may be discarded or returned to the sender without action. - END OF SECTION 01 33 00 - Ramapo College of New Jersey 01 33 00 SUBMITTAL PROCEDURES E-Wing Renovation for Teacher’s Education Page 5 of 5 RCNJ Project No. 11-210C Prepared by: Cambridge Construction Management
SECTION 01 40 00 – QUALITY REQUIREMENTS PART 1 - GENERAL 1.1 SUMMARY A. This Section specifies administrative and procedural requirements for quality control services. B. Quality control services include inspections and tests and related actions including reports, performed by independent agencies, governing authorities, and the Contractor. They do not include Contract enforcement activities performed by the Architect or Construction Manager. C. Inspection and testing services are required to verify compliance with requirements specified or indicated. These services do not relieve the Contractor of responsibility for compliance with Contract Document requirements. D. Requirements of this Section relate to customized fabrication and installation procedures, not production of standard products. 1. Specific quality control requirements for individual construction activities are specified in the Sections that specify those activities. Those requirements, including inspections and tests, cover production of standard products as well as customized fabrication and installation procedures. 2. Inspections, test and related actions specified are not intended to limit the Contractor's quality control procedures that facilitate compliance with Contract Document requirements. 3. Requirements for the Contractor to provide quality control services required by the Architect, Construction Manager or Owner, or authorities having jurisdiction are not limited by provisions of this Section. 1.2 RESPONSIBILITIES A. Contractor Responsibilities: The Owner shall provide inspections, tests and similar quality control services, specified in individual Specification Sections and required by governing authorities, except where they are specifically indicated to be the Contractor’s responsibility, or are provided by another identified entity; these services include those specified to be performed by an independent agency and not by the Contractor. 1. The Owner shall employ and pay an independent agency, to perform specified quality control services. 2. Retesting: The Contractor is responsible for retesting costs where results of required inspections, tests or similar services prove unsatisfactory and do not indicate compliance with Contract Document requirements, regardless of whether the original test was the Contractor's responsibility. a. Cost of retesting construction revised or replaced by the Contractor is the Contractor's responsibility. Ramapo College of New Jersey 01 40 00 QUALITY REQUIREMENTS E-Wing Renovation for Teacher’s Education Page 1 of 5 RCNJ Project No. 11-210C Prepared by: Cambridge Construction Management
Page 1 and 2:
E-WING RENOVATION FOR TEACHER’S E
Page 3 and 4:
18 - GENERAL CONDITIONS 19 - REQUES
Page 5 and 6:
BID REQUEST COVER SHEET (FOR CONSTR
Page 7 and 8:
***********************************
Page 9 and 10:
SUBCONTRACTORS AND THEIR REFERENCES
Page 11 and 12:
The Bidder agrees that this bid sha
Page 13 and 14:
RAMAPO COLLEGE OF NEW JERSEY STOCKH
Page 15 and 16:
CONTRACT FOR CONSTRUCTION Agreement
Page 17 and 18:
Owner Contractor Agreement 11. CONT
Page 19 and 20:
Owner Contractor Agreement ATTEST:
Page 21 and 22:
RAMAPO COLLEGE OF NEW JERSEY BID SE
Page 23 and 24:
RAMAPO COLLEGE OF NEW JERSEY PERFOR
Page 25 and 26:
RAMAPO COLLEGE OF NEW JERSEY PAYMEN
Page 27 and 28:
Ramapo College of New Jersey 505 Ra
Page 29 and 30:
(1) To notify the Public Agency Com
Page 31 and 32:
subcontractor agrees that, in imple
Page 33 and 34:
3. The executive head of each depar
Page 35 and 36:
easonable suspicion that such cause
Page 37 and 38:
E-Wing Renovation for Teacher’s E
Page 39 and 40:
Page 41 and 42:
In the procurement process, our pub
Page 43 and 44:
13. The provisions of sections 1 th
Page 45 and 46:
WHEREAS, robust competition for pub
Page 47 and 48:
incorporate good faith effort requi
Page 49 and 50:
APPENDIX A LIST OF REPORTING AGENCI
Page 51 and 52:
APPENDIX C It is the policy of the
Page 53 and 54:
Page 56 and 57:
Academic Complex Academic Wings Ang
Page 58 and 59:
• Using Route 208: Follow 208 Nor
Page 60 and 61:
THE PUBLIC WORKS CONTRACTOR REGISTR
Page 62 and 63:
(8) NJ Business Registration Certif
Page 64 and 65:
e. The Contracting Officer reserves
Page 66 and 67:
IB9.2 Every request for an interpre
Page 68 and 69:
Ramapo College of New Jersey E-Wing
Page 70 and 71:
12.2 Safety of Persons and Property
Page 72 and 73:
epresenting the College personally
Page 74 and 75:
1.2.8 The sequence of precedence pe
Page 76 and 77:
expeditiously commences to prosecut
Page 78 and 79:
ARTICLE 3 CONSTRUCTION MANAGER AND
Page 80 and 81:
ARTICLE 4 THE CONTRACTOR 4.1 Review
Page 82 and 83:
shall be provided and accomplished
Page 84 and 85:
d. Removal of spots, paint and soil
Page 86 and 87:
Drawings, Product Data, Samples or
Page 88 and 89:
4.12.3 Replace, fit, patch and repa
Page 90 and 91:
4.18.2 License and/or Royalty Fees
Page 92 and 93:
employed by any of them or anyone f
Page 94 and 95:
3. Arrange content by systems under
Page 96 and 97:
ARTICLE 6 PROJECT SPECIFIC CONDITIO
Page 98 and 99: 7.5.2 Should the Contractor elect t
Page 100 and 101: ARTICLE 8 RELATIONSHIP BETWEEN THE
Page 102 and 103: epresentative shall meet with the C
Page 104 and 105: Consultant's analysis, would have b
Page 106 and 107: did not affect the project critical
Page 108 and 109: 10.1 Contractor Payments from the C
Page 110 and 111: (4) reasonable evidence that the Wo
Page 112 and 113: Payment Act and by the 30th day aft
Page 114 and 115: 11.1 Uncovering of Work ARTICLE 11
Page 116 and 117: 12.1 Safety Precautions and Program
Page 118 and 119: 13.1 Contractor Insurance Requireme
Page 120 and 121: ARTICLE 14 CHANGES IN THE WORK 14.1
Page 122 and 123: 14.2.8 Where the cost of property m
Page 124 and 125: ARTICLE 16 AFFIRMATIVE ACTION REQUI
Page 126 and 127: (2) To notify any minority and fema
Page 128 and 129: (E) The contractor and its subcontr
Page 130 and 131: SECTION 01 11 00 - SUMMARY OF WORK
Page 132 and 133: SECTION 01 11 05 - TIME OF COMPLETI
Page 134 and 135: SECTION 01 29 00 - PAYMENT PROCEDUR
Page 140 and 141: SECTION 01 31 19 - PROJECT MEETINGS
Page 142 and 143: SECTION 01 31 19 - PROJECT MEETINGS
Page 144 and 145: SECTION 01 33 00 - SUBMITTAL PROCED
Page 146 and 147: SECTION 01 33 00 - SUBMITTAL PROCED
Page 150 and 151: SECTION 01 40 00 - QUALITY REQUIREM
Page 152 and 153: SECTION 01 40 00 - QUALITY REQUIREM
Page 154 and 155: SECTION 01 42 19 - REFERENCE STANDA
Page 156 and 157: SECTION 01 42 19 - REFERENCE STANDA
Page 158 and 159: SECTION 01 70 00 - CLOSEOUT 2. Resu
Page 160 and 161: SECTION 01 70 00 - CLOSEOUT 1.5 FIN
Page 162 and 163: SECTION 01 70 00 - CLOSEOUT Partial
Page 164 and 165: RAMAPO COLLEGE OF NEW JERSEY TEACHE
show all

Project Manual 11-210C - Ramapo College of New Jersey

Create successful ePaper yourself

Delete template?

Save as template?