Navy Electricity and Electronics Training Series - Historic Naval ...

More documents

Recommendations

Info

MINIATURE ELECTRONICS are card assemblies and modules composed exclusively of discreteelectronic components.SYSTEM PACKAGING refers to the design of a system, taking into account environmental andelectronic characteristics, access, and maintainability.PACKAGING LEVELS 0 to IV are used to identify assemblies within a system. Packaging levelsare as follows:LEVEL 0-Nonrepairable parts (resistors, diodes, and so forth.)LEVEL I -Submodules attached to circuit cards.LEVEL II -Circuit cards and MOTHER BOARDS.LEVEL III - Drawers.1-50
LEVEL IV - Cabinets.The most common METHODS OF INTERCONNECTION are the conventional pcb, themultilayer pcb, and modular assemblies.1-51
Page 1 and 2:
NONRESIDENTTRAININGCOURSESEPTEMBER
Page 3 and 4:
PREFACEBy enrolling in this self-st
Page 5:
TABLE OF CONTENTSCHAPTERPAGE1. Micr
Page 8 and 9:
Module 11, Microwave Principles, ex
Page 10 and 11:
INSTRUCTIONS FOR TAKING THE COURSEA
Page 12 and 13:
THIS PAGE LEFT BLANK INTENTIONALLY.
Page 15 and 16: CHAPTER 1MICROELECTRONICSLEARNING O
Page 17 and 18: VACUUM-TUBE EQUIPMENTVacuum tubes w
Page 19 and 20: SOLID-STATE DEVICESNow would be a g
Page 21 and 22: FILM INTEGRATED CIRCUITS are broken
Page 23 and 24: Development of a microelectronic de
Page 25 and 26: Figure 1-9.—Crystal furnace.The c
Page 27 and 28: Figure 1-12.—Planar-diffused tran
Page 29 and 30: Figure 1-14.—Vacuum evaporation o
Page 31 and 32: Figure 1-17.—Cathode-sputtering m
Page 33 and 34: Q23. How do the two types of monoli
Page 35 and 36: Figure 1-21A.—TO-5 mounting PLUG-
Page 37 and 38: Dual Inline PackageThe dual inline
Page 39 and 40: wafer, as shown in figure 1-27. Thi
Page 41 and 42: Figure 1-29.—J-K flip-flop discre
Page 43 and 44: Figure 1-31.—Lead numbering for a
Page 45 and 46: Figure 1-34.—Manufacturer's Data
Page 47: comparison to the distance between
Page 50 and 51: LEVEL III.—Drawers or pull-out ch
Page 52 and 53: Conductors located several layers b
Page 54 and 55: Figure 1-43A.—Evolution of modula
Page 56 and 57: ENVIRONMENTAL CONSIDERATIONSThe env
Page 58 and 59: SUMMARYThis topic has presented inf
Page 60 and 61: Rapid development has resulted in i
Page 62 and 63: Large DIPs are being used to packag
Page 66 and 67: Three methods of interconnecting ci
Page 68 and 69: ANSWERS TO QUESTIONS Q1. THROUGH Q5
Page 70 and 71: A43. Conventional printed circuit b
Page 72 and 73: Upon satisfactory completion of a 2
Page 74 and 75: One such improvement in system test
Page 76 and 77: those that should be observed when
Page 78 and 79: Figure 2-2.—Low voltage Handpiece
Page 80 and 81: Figure 2-6.—Rotary-drive machine
Page 82 and 83: Figure 2-9.—Pana Vise.HAND TOOLSF
Page 84 and 85: Figure 2-10a.—Pliers.TweezersView
Page 86 and 87: Even though all the items are not u
Page 88 and 89: Figure 2-14.—Stereoscopic zoom mi
Page 90 and 91: other than eutectic, go through a p
Page 92 and 93: A1. Chief of Naval Operations (CNO)
Page 94 and 95: CAUTIONTHIS SECTION IS NOT, IN ANY
Page 96 and 97: The coating material can best be id
Page 98 and 99: Figure 3-3.—Rotary tool conformal
Page 100 and 101: Figure 3-4A.—Eyelets (interfacial
Page 102 and 103: Figure 3-5B.—Clinched leads. SEMI
Page 104 and 105: Figure 3-8A.—Terminals. PIN AND T
Page 106 and 107: Figure 3-8E.—Terminals. SOLDER CU
Page 108 and 109: Figure 3-10.—Solder wicking.This
Page 110 and 111: Figure 3-12B.—Motorized vacuum/pr
Page 112 and 113: INSTALLATION AND SOLDERING OF PRINT
Page 114 and 115:
Figure 3-15.—Component arrangemen
Page 116 and 117:
Figure 3-16.—Thermal shunt.APPLIC
Page 118 and 119:
Removal of Plug-In DIPsTo remove pl
Page 120 and 121:
Figure 3-19.—TO mounting techniqu
Page 122 and 123:
Figure 3-21.—Flat pack in protect
Page 124 and 125:
Figure 3-23.—Pcb conductor damage
Page 126 and 127:
REPAIRING DELAMINATED CONDUCTORS.
Page 128 and 129:
5. The repair is completed using th
Page 130 and 131:
SAFETYSafety is a subject of utmost
Page 132 and 133:
OBJECT OR PROCESSWORK SURFACESFLOOR
Page 134 and 135:
8. When moving an ESDS device or as
Page 136 and 137:
Power ToolsHazards associated with
Page 138 and 139:
dispensers will prevent many accide
Page 140 and 141:
A GOOD SOLDER JOINT is bright and s
Page 142 and 143:
ANSWERS TO QUESTIONS Q1. THROUGH Q3
Page 145 and 146:
APPENDIX IGLOSSARYALLOWANCE PARTS L
Page 147 and 148:
MODULAR PACKAGING—Circuit assembl
Page 149:
APPENDIX IIREFERENCE LISTCHAPTER ON
Page 152 and 153:
Microelectronics—Continuedpackagi
Page 155:
Assignment QuestionsInformation: Th
Page 158 and 159:
1-7. Which of the following charact
Page 160 and 161:
1-24. Vacuum evaporation and cathod
Page 162 and 163:
___________________________________
Page 164 and 165:
1-49. Ground planes and shielding a
Page 166 and 167:
1-65. Which of the following types
Page 168 and 169:
ASSIGNMENT 2Textbook assignment: Ch
Page 170 and 171:
2-20. Turret, fork, and hook termin
Page 172 and 173:
2-39. Component leads may be clippe
Page 174 and 175:
2-52. To ensure a good mechanical b
show all

Navy Electricity and Electronics Training Series - Historic Naval ...

Create successful ePaper yourself

Delete template?

Save as template?