Christie LW600 Serial Communications Protocol-Expanded

More documents

Recommendations

Info

Status Read Commands9.7.13 CR_IDSLOT1 CommandCommand“CR_IDSLOT1” [CR]Detail Get ID information on Slot 1.This command is used to recognize the inserted board and specifythe valid Input source.Response Acceptable “000_%1” [CR]%1 “00” - Video boardValid Input Source: VIDEO, YC, S-VIDEO“01” - D-sub boardValid Input Source: ANALOG“04” - Component boardValid Input Source: ANALOG, YPBPR“06” - HD-SDI boardValid Input Source: HD-SDI“07” - SD-SDI boardValid Input Source: SD-SDI“08” - DUAL-SDI boardValid Input Source: SDI1, SDI2“09” - HDCP-DVI boardValid Input Source: DIGITAL, ANALOG, HDCP,SCART“18” - New HDCP-DVI boardValid Input Source: DIGITAL, ANALOG, HDCP,SCART“19” - New Component & Video boardValid Input Source: ANALOG, YPBPR,VIDEO,S-VIDEO“30” - On-board(DVI-DSub+D-Sub)Valid Input Source: DIGITAL, ANALOG, HDCP,SCART“42” - On-board(5BNC+S-video)Valid Input Source: ANALOG, YPBPR,VIDEO,S-VIDEO“99” - No board insertedUnacceptable “?” [CR]9-18 LW600-LX900-LX1000 RS232 Codes-Expanded Technical Reference Information020-000046-02 Rev 2 (07-2011)
Status Read Commands9.7.14 CR_IDSLOT2 CommandCommand“CR_IDSLOT2” [CR]Detail Get ID information on Slot 2.This command is to recognize the inserted slot board and specifythe valid Input source.Response Acceptable “000_%1” [CR]%1 The same as CR_IDSLOT1Unacceptable “?” [CR]9.7.15 CR_IDSLOT3 CommandCommand“CR_IDSLOT3” [CR]Detail Get ID information on Slot 3.This command is to recognize the inserted slot board and specifythe valid Input source.Response Acceptable “000_%1” [CR]%1 The same as CR_IDSLOT1Unacceptable“?” [CR]9.7.16 CR_IDSLOT4 CommandCommand“CR_IDSLOT4” [CR]Detail Get ID information on Slot 4.This command is to recognize the inserted slot board and specifythe valid Input source.Response Acceptable “000_%1” [CR]%1 The same as CR_IDSLOT1Unacceptable“?” [CR]LW600-LX900-LX1000 RS232 Codes-Expanded Technical Reference Information 9-19020-000046-02 Rev 2 (07-2011)
Page 1:
LW600-LX900-LX1000 RS232Codes-Expan
Page 9:
Table of Contents10.2.2 Command pip
Page 13:
Status Read Commands2 Serial Interf
Page 17:
Status Read Commands4 NotationData
Page 20 and 21:
Status Read Commands5.2 PC Control
Page 23 and 24:
Status Read Commands6 Status Read C
Page 25 and 26:
Status Read Commands6.6 Lamp Status
Page 27:
Status Read Commands7 Error Code Ta
Page 30 and 31: Status Read Commands8.3 Operation R
Page 32 and 33: Status Read Commands8.4.7 CF_APCTRL
Page 34 and 35: Status Read Commands8.4.13 CF_NZRED
Page 36 and 37: Status Read Commands8.4.16 CF_IMAGE
Page 38 and 39: Status Read Commands8.5.4 CF_V-POS
Page 40 and 41: Status Read Commands8.5.8 CF_SETPCA
Page 42 and 43: Status Read Commands8.6 Input Contr
Page 44 and 45: Status Read CommandsCommand“CF_SY
Page 46 and 47: Status Read Commands8.7.2 CF_DZCENT
Page 48 and 49: Status Read Commands8.7.7 CF_VSCALE
Page 50 and 51: Status Read Commands8.7.9 CF_HSCALE
Page 52 and 53: Status Read Commands8.8.2 CF_LAMPMO
Page 54 and 55: Status Read Commands8.9.3 CF_BACKGN
Page 56 and 57: Status Read Commands8.9.6 CF_RCODE
Page 58 and 59: Status Read Commands8.9.11 CF_PJPIN
Page 60 and 61: Status Read Commands8.9.18 CF_KEYDI
Page 63 and 64: Status Read Commands9 Status Read C
Page 65 and 66: Status Read Commands9.4.6 CR_COLTEM
Page 67 and 68: Status Read Commands9.4.16 CR_PROGV
Page 69 and 70: “?” [CR] - When unknown command
Page 71 and 72: Status Read Commands9.5.8 CR_SETPCA
Page 73 and 74: Status Read Commands9.5.10 CR_PCSTO
Page 75 and 76: Status Read Commands9.7.3 CR_SYSTEM
Page 77 and 78: Status Read Commands%1 “DIGITAL
Page 79: Status Read Commands9.7.9 CR_NMSLOT
Page 83 and 84: Status Read Commands9.8.4 CR_REAR C
Page 85 and 86: Status Read Commands9.9.4 CR_LAMPST
Page 87 and 88: Status Read Commands9.10.2 CR_DISP
Page 89 and 90: Status Read Commands9.10.9 CR_P-MAN
Page 91 and 92: Status Read Commands9.10.17 CR_PJLO
Page 93 and 94: Status Read Commands9.10.24 CR_TEST
Page 95 and 96: Status Read Commands9.11.6 CR_TEMPW
Page 97: Status Read Commands9.11.9 CR_SHUTC
Page 100 and 101: Status Read Commands10.2 Functional
show all

Christie LW600 Serial Communications Protocol-Expanded

Create successful ePaper yourself

Delete template?

Save as template?