Christie LW600 Serial Communications Protocol-Expanded

More documents

Recommendations

Info

Status Read Commands9.11.7 CR_TEMPFAIL CommandCommand“CR_TEMPFAIL” [CR]Detail Get the temperature inside the projector when the abnormal statusoccurs.It is possible to get the temperatures for more than one sensor all atonce if it is applicable.Response Acceptable “000_%1” [CR]%1 Example: “_31.5F”[CR] _ indicates a space. Whenthe temperature goes under 0, the first character is“-”, not a space, as in “-05.5F”.With more than one temperature sensors installed,projector returns the responses for each sensor in arow.Example: “_31.5F_35.2S” [CR]The first data indicates sensor 1 data, then onespace, and sensor 2 data is followed. Last characterin each data indicates the sensor’s status.In the abnormal temperature - “F”In the safe level of temperature -“S”Neither in or close to the abnormal temp. -“N”The second example above indicates that thetemperature detected by sensor 1 is 31.5 whichmeans in the abnormal temperature, and at sensor 2is 32.5 degrees which is in the safe temperature.When the abnormal temperature status is notoccurred the data should be “_00.0S”.When the projector is reset, “_00.0S” is set.Every time abnormal temperature status is detected,it renews the data and returns it.It only returns the renewed data of the latestabnormal temperature and the previous data iscleared.Unacceptable “?” [CR]9.11.8 CR_SERIALNO CommandCommandDetail“CR_SERIALNO” [CR]Get value of the serial number. (For Dealer)Response Acceptable “000_%1” [CR]%1 Eight digits of alphanumeric charactersUnacceptable“?” [CR]9-34 LW600-LX900-LX1000 RS232 Codes-Expanded Technical Reference Information020-000046-02 Rev 2 (07-2011)
Status Read Commands9.11.9 CR_SHUTCOND CommandCommand “CR_SHUTCOND” [CR]Detail Get setting status of ShutterResponse Acceptable “000_%1” [CR]%1 “SAFE” - Shutter operation is normal.“FAIL” - Shutter operation is abnormal.Unacceptable “?” [CR]LW600-LX900-LX1000 RS232 Codes-Expanded Technical Reference Information 9-35020-000046-02 Rev 2 (07-2011)
Page 1:
LW600-LX900-LX1000 RS232Codes-Expan
Page 9:
Table of Contents10.2.2 Command pip
Page 13:
Status Read Commands2 Serial Interf
Page 17:
Status Read Commands4 NotationData
Page 20 and 21:
Status Read Commands5.2 PC Control
Page 23 and 24:
Status Read Commands6 Status Read C
Page 25 and 26:
Status Read Commands6.6 Lamp Status
Page 27:
Status Read Commands7 Error Code Ta
Page 30 and 31:
Status Read Commands8.3 Operation R
Page 32 and 33:
Status Read Commands8.4.7 CF_APCTRL
Page 34 and 35:
Status Read Commands8.4.13 CF_NZRED
Page 36 and 37:
Status Read Commands8.4.16 CF_IMAGE
Page 38 and 39:
Status Read Commands8.5.4 CF_V-POS
Page 40 and 41:
Status Read Commands8.5.8 CF_SETPCA
Page 42 and 43:
Status Read Commands8.6 Input Contr
Page 44 and 45:
Status Read CommandsCommand“CF_SY
Page 46 and 47: Status Read Commands8.7.2 CF_DZCENT
Page 48 and 49: Status Read Commands8.7.7 CF_VSCALE
Page 50 and 51: Status Read Commands8.7.9 CF_HSCALE
Page 52 and 53: Status Read Commands8.8.2 CF_LAMPMO
Page 54 and 55: Status Read Commands8.9.3 CF_BACKGN
Page 56 and 57: Status Read Commands8.9.6 CF_RCODE
Page 58 and 59: Status Read Commands8.9.11 CF_PJPIN
Page 60 and 61: Status Read Commands8.9.18 CF_KEYDI
Page 63 and 64: Status Read Commands9 Status Read C
Page 65 and 66: Status Read Commands9.4.6 CR_COLTEM
Page 67 and 68: Status Read Commands9.4.16 CR_PROGV
Page 69 and 70: “?” [CR] - When unknown command
Page 71 and 72: Status Read Commands9.5.8 CR_SETPCA
Page 73 and 74: Status Read Commands9.5.10 CR_PCSTO
Page 75 and 76: Status Read Commands9.7.3 CR_SYSTEM
Page 77 and 78: Status Read Commands%1 “DIGITAL
Page 79 and 80: Status Read Commands9.7.9 CR_NMSLOT
Page 81 and 82: Status Read Commands9.7.14 CR_IDSLO
Page 83 and 84: Status Read Commands9.8.4 CR_REAR C
Page 85 and 86: Status Read Commands9.9.4 CR_LAMPST
Page 87 and 88: Status Read Commands9.10.2 CR_DISP
Page 89 and 90: Status Read Commands9.10.9 CR_P-MAN
Page 91 and 92: Status Read Commands9.10.17 CR_PJLO
Page 93 and 94: Status Read Commands9.10.24 CR_TEST
Page 95: Status Read Commands9.11.6 CR_TEMPW
Page 100 and 101: Status Read Commands10.2 Functional
show all

Christie LW600 Serial Communications Protocol-Expanded

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?