DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

More documents

Recommendations

Info

Appendix F: Hard Drive InstallationFormatting the Hard DriveAfter installing a new hard drive, you must format it before the system can recognize it.ATT<strong>EN</strong>TION: Formatting the HDD erases all data on the hard disk. This stepcannot be undone. System settings will not be erased.To format a hard drive:1. From Live View, right-click and select Main Menu>Advanced>HDD Management.2. Under HDD No., select the hard drive you would like to format. Information about the harddrive appears in the lower section of the menu.3. Under Set to, select Format.Click Apply. Click OK to confirm. Wait for the hard drive to format. Hard drives become Read/Writehard drives by default when formatted.Select HDDSelect FormatClick Execute106
TroubleshootingTROUBLESHOOTINGWhen a malfunction occurs, it may not be serious and can be corrected easily. The followingdescribes the most common problems and solutions. Please refer to the following before calling<strong>Digimerge</strong> Technical Support:Error Possible Causes Solutions• NVR is not receivingpower, or is notpowering up• There is no pictureon selected channels/ camera picture isnot being displayed• Remote control isnot detected by thesystem• Cable from power adapter isloose or is unplugged• Cables are connected, but NVRunit is not receiving sufficientpower• PoE power adapter is notconnected• Camera cables are loose orhave become disconnected• Camera/NVR connection toLAN has become interrupted• Batteries in the remote controlare drained• There are no batteries in theremote control• Confirm that all cables are connected correctly• Confirm that the power adapter is securelyconnected to the back of the unit• Confirm that the unit is powered on (LEDindicators on the front should be ON)• If the unit is connected through a power bar orsurge protector, try bypassing the bar andconnecting the power directly to the wall outlet• Confirm that there is power at the outlet:• Connecting the power cable to another outlet• Test the outlet with another plugged device(such as an electric calculator or phonecharger)• Make sure the 48V DC power adapter is connectedto the NVR or the cameras will not receive powerfrom the PoE Ports• Disconnect and reconnect the cable at the NVRand at the Camera• Try moving the camera to another channel or useanother cable• If your cameras are not using PoE, make sure theyare using the correct power source according to thespecifications provided by the manufacturer• Make sure your cameras are connected to thesame LAN as the NVR• Make sure any routers or switches in between theNVR and IP cameras are powered on• Install 2 fresh AAA batteries in the remote control107
Page 1:
DNR200V SeriesNetwork Video Surveil
Page 4 and 5:
Service13. Servicing - Do not attem
Page 6 and 7:
Features• Easy Connection and set
Page 8:
Updating Firmware . . . . . . . . .
Page 11 and 12:
GETTING STARTEDThe system comes wit
Page 13 and 14:
FRONT PANEL1 23451. IR Receiver: IR
Page 15 and 16:
REMOTE CONTROL1. Power: Press and h
Page 17 and 18:
Using the SystemUSING THE SYSTEMThe
Page 19 and 20:
Using the SystemOR Use Color mode t
Page 21 and 22:
Using the SystemUsing the Virtual K
Page 24 and 25:
Search (Playback)SEARCH (PLAYBACK)S
Page 26 and 27:
BACKUPBackup video files to externa
Page 28 and 29:
Backup2. Start playing back video u
Page 30 and 31:
Using the Main MenuUSING THE MAIN M
Page 32 and 33:
Using the Main Menu2. Copy the firm
Page 34 and 35:
Using the Main MenuRecordingstreami
Page 36 and 37:
Using the Main Menu• HTTP Port: U
Page 38 and 39:
Using the Main Menu• Port: Enter
Page 40 and 41:
Using the Main Menuoptions allow yo
Page 42 and 43:
Using the Main MenuAdvancedConfigur
Page 44 and 45:
Using the Main MenuBackup to use th
Page 46 and 47:
Using the Main MenuModifying Accoun
Page 48 and 49:
Using the Main Menu4. Click Export.
Page 50 and 51:
DigiNet NVR Central Management Soft
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
3. Check Search.Select alarm typeCh
Page 58 and 59:
Page 60 and 61:
• You may also select a task or p
Page 62 and 63:
2. Click on a display area in the m
Page 64 and 65:
Page 66 and 67: 2. Click Search to detect secondary
Page 68 and 69: 7. Click and drag cameras to the di
Page 70 and 71: 5. Click a search result and then c
Page 72 and 73: 5. Tap Add>Manually Add.Tap Add6. C
Page 74 and 75: Mobile ConnectivityUsing Playback M
Page 76 and 77: Mobile Connectivity3. Tap Motion De
Page 78 and 79: Mobile Connectivity6. Configure the
Page 80 and 81: Mobile ConnectivityUsing Playback M
Page 82 and 83: Mobile Connectivity5. Tap OK. A tes
Page 84 and 85: Mobile Connectivity10. Tap + on one
Page 86 and 87: Mobile Connectivity3. Tap + and sel
Page 88 and 89: Mobile Connectivity4. Tap OK. A tes
Page 90 and 91: Mobile Connectivity9. In landscape
Page 92 and 93: Mobile ConnectivityEnabling Push No
Page 94 and 95: Mobile Connectivity2. Tap . Tap OK
Page 96 and 97: Appendix A: System SpecificationsVi
Page 98 and 99: Appendix B: Setting up Remote Viewi
Page 100 and 101: Appendix C: Auto Port Forwarding Wi
Page 108 and 109: Appendix D: Setting Up DDNS Service
Page 110 and 111: Appendix E: Remote Firmware Upgrade
Page 112 and 113: Appendix E: Remote Firmware Upgrade
Page 114 and 115: Appendix F: Hard Drive Installation
Page 118 and 119: Troubleshooting• Hard drive is no
Page 120: Need Help?Please make sure to visit
show all

DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

Create successful ePaper yourself

Delete template?

Save as template?