DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

More documents

Recommendations

Info

DigiNet NVR Central Management Software2. Click Monitor Task.Click Monitor Task3. Click New.4. Enter a Task Name of your choice.5. Under Window, select the split-screen mode you would like to show in the task.6. Under Monitor Item, configure the following:• Window: Select the display window you would like to configure.• Device: Click and drag the camera from the Device List in the main CMS window to the fieldto add it.• Stream Type: Select Main Stream or Extra Stream to view the sub-stream.Enter Task nameSelect split-screen layoutSelect display windowDrag camera fromDevice ListSelect Main Streamor Extra StreamClick Add7. Click Add. Repeat Steps 6 & 7 to configure additional screens.8. Click OK. Click OK to save changes.Configuring ProjectsOnce you have multiple tasks set up, you can configure projects to automatically cycle throughthem.To configure a project:48
DigiNet NVR Central Management Software1. Click Config Manager>Scheme Task Config.2. Click Monitor Project.Click Monitor Project3. Click New.4. Enter a Name for the project. You may not change the name after the project is created.5. Under Mode, select Tour Mode or Schedule Mode. Tour Mode will cycle through tasks on afixed interval. Schedule Mode will switch tasks at a pre-defined time of the day.Enter project nameSelect project typeSelect taskEnter interval or start timeClick Add6. Under Task Name, select the task you would like to add to the project.• If you selected Tour Mode, enter the Interval Time in minutes that the task will run for beforechanging to the next task.• If you selected Schedule Mode, enter the time of day when the task will start running.7. Click Add.8. Repeat steps 6-7 for each additional task you would like to add to the project.9. Click OK. Click OK to save changes.Running Tasks and Projects• Once you have configured tasks or projects, you may run them by clicking Task (then selecting the task or project you would like to run.) and49
Page 1:
DNR200V SeriesNetwork Video Surveil
Page 4 and 5:
Service13. Servicing - Do not attem
Page 6 and 7:
Features• Easy Connection and set
Page 8: Updating Firmware . . . . . . . . .
Page 11 and 12: GETTING STARTEDThe system comes wit
Page 13 and 14: FRONT PANEL1 23451. IR Receiver: IR
Page 15 and 16: REMOTE CONTROL1. Power: Press and h
Page 17 and 18: Using the SystemUSING THE SYSTEMThe
Page 19 and 20: Using the SystemOR Use Color mode t
Page 21 and 22: Using the SystemUsing the Virtual K
Page 24 and 25: Search (Playback)SEARCH (PLAYBACK)S
Page 26 and 27: BACKUPBackup video files to externa
Page 28 and 29: Backup2. Start playing back video u
Page 30 and 31: Using the Main MenuUSING THE MAIN M
Page 32 and 33: Using the Main Menu2. Copy the firm
Page 34 and 35: Using the Main MenuRecordingstreami
Page 36 and 37: Using the Main Menu• HTTP Port: U
Page 38 and 39: Using the Main Menu• Port: Enter
Page 40 and 41: Using the Main Menuoptions allow yo
Page 42 and 43: Using the Main MenuAdvancedConfigur
Page 44 and 45: Using the Main MenuBackup to use th
Page 46 and 47: Using the Main MenuModifying Accoun
Page 48 and 49: Using the Main Menu4. Click Export.
Page 50 and 51: DigiNet NVR Central Management Soft
Page 56 and 57: 3. Check Search.Select alarm typeCh
Page 60 and 61: • You may also select a task or p
Page 62 and 63: 2. Click on a display area in the m
Page 66 and 67: 2. Click Search to detect secondary
Page 68 and 69: 7. Click and drag cameras to the di
Page 70 and 71: 5. Click a search result and then c
Page 72 and 73: 5. Tap Add>Manually Add.Tap Add6. C
Page 74 and 75: Mobile ConnectivityUsing Playback M
Page 76 and 77: Mobile Connectivity3. Tap Motion De
Page 78 and 79: Mobile Connectivity6. Configure the
Page 80 and 81: Mobile ConnectivityUsing Playback M
Page 82 and 83: Mobile Connectivity5. Tap OK. A tes
Page 84 and 85: Mobile Connectivity10. Tap + on one
Page 86 and 87: Mobile Connectivity3. Tap + and sel
Page 88 and 89: Mobile Connectivity4. Tap OK. A tes
Page 90 and 91: Mobile Connectivity9. In landscape
Page 92 and 93: Mobile ConnectivityEnabling Push No
Page 94 and 95: Mobile Connectivity2. Tap . Tap OK
Page 96 and 97: Appendix A: System SpecificationsVi
Page 98 and 99: Appendix B: Setting up Remote Viewi
Page 100 and 101: Appendix C: Auto Port Forwarding Wi
Page 108 and 109:
Appendix D: Setting Up DDNS Service
Page 110 and 111:
Appendix E: Remote Firmware Upgrade
Page 112 and 113:
Appendix E: Remote Firmware Upgrade
Page 114 and 115:
Appendix F: Hard Drive Installation
Page 116 and 117:
Appendix F: Hard Drive Installation
Page 118 and 119:
Troubleshooting• Hard drive is no
Page 120:
Need Help?Please make sure to visit
show all

DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?