DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

More documents

Recommendations

Info

Using the Main Menu2. Copy the firmware to a blank USB flashdrive.• Channel Status: Shows the IP address,model number, and camera status.NOTE: Do not have any folders on the USBflash drive—just the firmware file.3. Connect the USB flash drive to a USB porton the system.4. Right-click and then select MainMenu>Info>Version.5. Click Start to update firmware. Wait forthe firmware upgrade to complete. Do notremove the USB flash drive until theupgrade process is complete or power offthe NVR during the upgrade process.Online Users• Connection Log: Search for camera statuslogs, including user access to cameras.The Online Users sub-menu shows a list ofusers connected to the system using remotedevices. You may Disconnect a user for up to 18hours or Block a user from the system.• Net Load: Shows a graph of upload anddownload traffic for your system.Remote Device InfoThe Remote Device Info sub-menu showsinformation about IP cameras connected to thesystem, it contains the following tabs:22
Using the Main MenuSettingThe Setting menu allows you toconfigure general system, schedule,network, recording, display, andmotion settings. It also allows you to restorethe system to factory defaults.GeneralThe General sub-menu allows you to Configurethe time and general system settings.The General sub-menu contains the followingoptions:• System Time: Select the current date andtime and click Save to save changes.• Date Format: Select the date format (YYYYMM DD, MM DD YYYY, or DD MM YYYY).• Date Separator: Select if you would like adot (.), dash (-), or slash (/) to separate thedate display.• DST: Check to enable daylight savings timeadjustments. To configure the start and endtimes for daylight savings, click Set. Then,configure the Start and End as needed, andclick OK.• Time Format: Select 24-HOUR or12-HOUR.• Language: Select the system language.• Video Standard: Select NTSC (NorthAmerica) or PAL (Europe).• Device No.: Select the Remote control IDfor the NVR.• Device ID: Enter a custom name for theNVR.• HDD Full: Select Overwrite for the systemto begin overwriting the oldest recordingswhen the hard drive is full or select StopRecording for the system to stop recordingwhen the hard drive is full.• Pack Duration: Enter the desired packduration. The pack duration determinesthe duration of video files saved to thesystem.• Realtime Play: Select the duration ofvideos that will be played back in QuickPlayback mode. For example, if RealtimePlay is set to 5 minutes, Quick Playback willstart playing back video recorded from 5minutes ago on the selected channel.• Mouse Property: Click MouseSet, adjustthe double-click speed and click OK.• Startup Wizard: Check to enable theStartup Wizard when your system starts. Itis recommended to disable Startup Wizardonce you have configured the system.• Navigation: Check to enable the SystemToolbar that appears when left clicking onthe screen.• Auto Logout: Enter the amount of time thesystem will wait before logging a user outwhen idle.• IPC Time Sync: The NVR will regularly syncthe internal clocks of connected IPcameras. Enter the interval between timesyncs.NOTE: Click OK when finished makingchanges.23
Page 1: DNR200V SeriesNetwork Video Surveil
Page 4 and 5: Service13. Servicing - Do not attem
Page 6 and 7: Features• Easy Connection and set
Page 8: Updating Firmware . . . . . . . . .
Page 11 and 12: GETTING STARTEDThe system comes wit
Page 13 and 14: FRONT PANEL1 23451. IR Receiver: IR
Page 15 and 16: REMOTE CONTROL1. Power: Press and h
Page 17 and 18: Using the SystemUSING THE SYSTEMThe
Page 19 and 20: Using the SystemOR Use Color mode t
Page 21 and 22: Using the SystemUsing the Virtual K
Page 24 and 25: Search (Playback)SEARCH (PLAYBACK)S
Page 26 and 27: BACKUPBackup video files to externa
Page 28 and 29: Backup2. Start playing back video u
Page 30 and 31: Using the Main MenuUSING THE MAIN M
Page 34 and 35: Using the Main MenuRecordingstreami
Page 36 and 37: Using the Main Menu• HTTP Port: U
Page 38 and 39: Using the Main Menu• Port: Enter
Page 40 and 41: Using the Main Menuoptions allow yo
Page 42 and 43: Using the Main MenuAdvancedConfigur
Page 44 and 45: Using the Main MenuBackup to use th
Page 46 and 47: Using the Main MenuModifying Accoun
Page 48 and 49: Using the Main Menu4. Click Export.
Page 50 and 51: DigiNet NVR Central Management Soft
Page 56 and 57: 3. Check Search.Select alarm typeCh
Page 60 and 61: • You may also select a task or p
Page 62 and 63: 2. Click on a display area in the m
Page 66 and 67: 2. Click Search to detect secondary
Page 68 and 69: 7. Click and drag cameras to the di
Page 70 and 71: 5. Click a search result and then c
Page 72 and 73: 5. Tap Add>Manually Add.Tap Add6. C
Page 74 and 75: Mobile ConnectivityUsing Playback M
Page 76 and 77: Mobile Connectivity3. Tap Motion De
Page 78 and 79: Mobile Connectivity6. Configure the
Page 80 and 81: Mobile ConnectivityUsing Playback M
Page 82 and 83:
Mobile Connectivity5. Tap OK. A tes
Page 84 and 85:
Mobile Connectivity10. Tap + on one
Page 86 and 87:
Mobile Connectivity3. Tap + and sel
Page 88 and 89:
Mobile Connectivity4. Tap OK. A tes
Page 90 and 91:
Mobile Connectivity9. In landscape
Page 92 and 93:
Mobile ConnectivityEnabling Push No
Page 94 and 95:
Mobile Connectivity2. Tap . Tap OK
Page 96 and 97:
Appendix A: System SpecificationsVi
Page 98 and 99:
Appendix B: Setting up Remote Viewi
Page 100 and 101:
Appendix C: Auto Port Forwarding Wi
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Appendix D: Setting Up DDNS Service
Page 110 and 111:
Appendix E: Remote Firmware Upgrade
Page 112 and 113:
Appendix E: Remote Firmware Upgrade
Page 114 and 115:
Appendix F: Hard Drive Installation
Page 116 and 117:
Appendix F: Hard Drive Installation
Page 118 and 119:
Troubleshooting• Hard drive is no
Page 120:
Need Help?Please make sure to visit
show all

DNR200V_SERIES_MANUAL_EN_R1_web - Digimerge

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?