catalogo-8020_compressed

20 Series Metric 15 Series 10 Series Fractional
Machining Services
Tap Profile End
Part Description:
The tap profile end machining service is used to add threads to the extruded holes in a T-slot profile. This
enables the insertion of a bolt to mount an end fastener or accessories. There are a wide variety of sizes
and depths available. Additional Information: When ordering this service, designate which profile end
(left, right, or both) requires the tap.
Part No. Series Tap Size Minimum Depth Service Type Applicable Profiles
7061 1/4-20 1.125” Single Hole End Tap 1001, 1001-S, 1002, 1002-S, 1003, 1003-S, 1004, 1004-S, 1010,
7063 M6 x 1.00 1.125” Single Hole End Tap 1010-S, 1012, 1012-S
7006 10-32 .875” Two Hole End Tap
7007 M5 x .80 .875” Two Hole End Tap
1050
7008 10-32 .875” Two Hole End Tap
7009 M5 x .80 .875” Two Hole End Tap
2012
7046 1/4-20 1.125” Two Hole End Tap
7047 M6 x 1.00 1.125” Two Hole End Tap
1020, 1020-S
7036 1/4-20 1.125” Three Hole End Tap
7037 M6 x 1.00 1.125” Three Hole End Tap
1030, 1030-S
7064 1/4-20 1.125” Four Hole End Tap
7067 M6 x 1.00 1.125” Four Hole End Tap
2020, 2020-S
7038 1/4-20 1.125” Eight Hole End Tap
7039 M6 x 1.00 1.125” Eight Hole End Tap
2040, 2040-S
7035 1/8 NPT — Single Hole End Tap
7060 5/16-18 1.250” Single Hole End Tap
7059 M8 x 1.25 1.250” Single Hole End Tap 1501, 1501-LS, 1502, 1502-LS, 1503, 1503-LS, 1504, 1504-LS, 1515,
7025 3/8-16 1.500” Single Hole End Tap 1515-S, 1515-Lite, 1515-LS, 1515-UL, 1515-ULS, 1517, 1517-LS, 1547
7053 M10 x 1.50 1.500” Single Hole End Tap
7054 7/16-14 1.500” Single Hole End Tap
7014 5/16-18 1.250” Two Hole End Tap
7015 M8 x 1.25 1.250” Two Hole End Tap
1534-Lite, 1575
7016 5/16-18 1.250” Two Hole End Tap
7017 M8 x 1.25 1.250” Two Hole End Tap
3034-Lite, 3075
7045 5/16-18 1.250” Two Hole End Tap
7048 M8 x 1.25 1.250” Two Hole End Tap
7024 3/8-16 1.500” Two Hole End Tap 1530, 1530-S, 1530-Lite, 1530-LS, 1530-UL, 1530-ULS
7032 M10 x 1.50 1.500” Two Hole End Tap
7033 7/16-14 1.500” Two Hole End Tap
7049 3/8-16 1.500” Three Hole End Tap
7026 5/16-18 1.250” Three Hole End Tap 1545, 1545-S, 1545-LS
7028 M8 x 1.25 1.250” Three Hole End Tap
7052 3/8-16 1.500” Four Hole End Tap
7055 5/16-18 1.250” Four Hole End Tap 3030, 3030-S, 3030-Lite, 3030-LS
7056 M8 x 1.25 1.250” Four Hole End Tap
7057 3/8-16 1.500” Eight Hole End Tap
7029 5/16-18 1.250” Eight Hole End Tap 3060
7031 M8 x 1.25 1.250” Eight Hole End Tap
20-7063 M5 x .80 22.23mm Single Hole End Tap
20-7061 10-32 22.23mm Single Hole End Tap
20-2020
MACHINING SERVICES
CONTINUE
For the most up to date information on 80/20 ® products visit 8020.net
861