catalogo-8020_compressed

Machining Services
Profile Miter Cut
Fractional 10 Series 15 Series
Metric
20 Series 25 Series 30 Series 40 Series 45 Series
Part Description:
The profile miter cut is used to create custom-angled supports. T-slotted profiles can be miter cut to angles of
15 to 90 degrees or 30 to 90 degrees for select profiles (with the exception of 3060 and 40-8016, which can
only be cut to an angle of 45 degrees across the 6.00” (160mm) side. Select structural shapes may also be
mitered. See the miter cut worksheet on page 869 for guidelines. Additional Information: When ordering
this service, designate which profile end (left, right, or both) requires the miter. A drawing is required with
this machining service; for project design assistance contact a Design Technician at www.8020.net.
0º
Minimum and Maximum
Angle Refers to Dimension A
A
Part No. Series Applicable Profiles Minimum Angle Maximum Angle
MACHINING SERVICES
7066 1001, 1001-S, 1002, 1002-S, 1003, 1003-S, 1004, 1004-S, 1010, 1010-S, 1012, 1012-S, 1050 0º 75º
7070 1020, 1020-S, 2012 0º 75º
7072 1030, 1030-S 0º 75º
7071 2020, 2020-S 0º 75º
7073 2040, 2040-S 0º 60º
7065
1501, 1501-LS, 1502, 1502-LS, 1503, 1503-LS, 1504, 1504-LS, 1515, 1515-S, 1515-Lite, 1515-LS,
1515-UL, 1515-ULS, 1517, 1517-LS, 1534-Lite, 1547, 1575
0º 75º
7075 1530, 1530-Lite, 1530-LS, 1530-S, 1530-UL, 1530-ULS, 3034-Lite, 3075 0º 60º
7076 1545, 1545-S, 1545-LS 0º 60º
7085 3030, 3030-Lite, 3030-LS, 3030-S 0º 60º
7087 3060 0º 45º
20-7065 20-2020 0º 75º
20-7075 20-2040 0º 60º
20-7085 20-4040 0º 60º
25-7066 25-2501, 25-2502, 25-2503, 25-2504, 25-2525, 25-2527, 25-2514 0º 75º
25-7070 25-2550, 25-5013 0º 60º
25-7071 25-5050 0º 60º
25-7072 25-2576 0º 60º
25-7073 25-5010 0º 45º
30-7065 30-3001, 30-3002, 30-3003, 30-3004, 30-3030, 30-3022 0º 75º
30-7075 30-3060 0º 60º
30-7085 30-6060 0º 60º
40-7065
40-4001, 40-4002, 40-4003, 40-4004, 40-4040, 40-4040-Lite, 40-4040-UL, 40-4030-Lite,
40-4045-Lite, 40-4020
0º 75º
40-7075 40-4080, 40-4080-Lite, 40-4080-UL, 40-4082-Lite, 40-4083-Lite, 40-4084-Lite, 40-4085-Lite, 40-8020 0º 60º
40-7076 40-4012 0º 60º
40-7085 40-8080 0º 60º
40-7087 40-8016 0º 45º
45-7065 45-4545, 45-4545-Lite 0º 75º
45-7075 45-4590 0º 60º
Continue to the next page for a Profile Miter Cut Worksheet
CONTINUE
868
For the most up to date information on 80/20 ® products visit 8020.net