3980xpi Users Manual - Data I/O Corporation

More documents

Recommendations

Info

Introduction Specifications Power Requirements Note: Unless otherwise noted, the specifications apply to all four programmers. Electrostatic Discharge (ESD) Functional Operating Voltages 90 to 264 VAC Frequency Range 50 to 60 Hz Power Consumption 150 VA maximum Input Current 1.5A maximum IEC 801-2 (± 8 kV) RAM 8MB standard 4 MB standard (after 8/97); 8 MB optional—2900 Floppy Disk Format Quad-density, dual-sided 3.5-inch disk with 135 tracks per inch. 1.44 MB formatted. Controller Motorola 68000 16-bit microprocessor. Terminal Support Interfaces with ANSI 3.64 compatible terminals, IBM PCs, and compatibles using a terminal emulator, and many popular ASCII terminals. Communication Standard RS-232C SmartPort Automatic DTE/DCE port configuration Data Transfer Rate 110 to 19.2 K baud (up to 115.2 K baud using HiTerm or TaskLink) Parallel Port Standard 1-6 3980xpi/3980/3900/2900 User Manual
Physical and Environmental Safety Introduction Dimension 9.53h x 28.58w x 41.28d cm 3.75h x 11.25w x 16.25d inches Weight 3980xpi Operating: 5.12 kg (11.28lb) Shipping: 7.38 kg (16.28lb) 3980: Operating: 5.10 kg (11.22 lb) Shipping: 7.36 kg (16.22 lb) 3900: Operating: 5.00 kg (11.0 lb) Shipping: 7.26 kg (16.0 lb) 2900 Operating: 3.86 kg (8.5 lb) Shipping: 6.14 kg (13.5 lb) Temperature Operating: Storage: Transportation: Relative Humidity Operating: Storage: Altitude Operating: Storage: The 3980xpi and all legacy programmers are certified by UL and CSA to comply with the following safety standards: Certificate of RFI/EMI Compliance Underwriters Laboratories—UL 60950 Third Edition and/or EN 60950 Third Edition Data I/O certifies that the 3980xpi and all legacy programmers comply with the Radio Frequency Interference (RFI) and Electromagnetic Interference (EMI) requirements of EN55022 Class A and EN50082-1 as called out in 89/ 336/EEC, the EMC Directive for the European Community. Performance Verification R EC conformity mark. +4°C to +40°C (+40°F to +105°F) +4°C to +50°C (+40°F to + 122°F) –40°C to +55°C (–40°F to +130°F) 20 to 80% noncondensing 10 to 90% noncondensing To 5,000 meters To 15,000 meters The programmer verifies internal voltages every time it is powered up and every time a complete self-test is run. The voltage verification is performed by software and is compared to a laser-trimmed voltage reference. Data I/O recommends that you cycle power AND run a complete selftest cycle at least once a day. To ensure that your programmer continues to meet product performance specifications, Data I/O recommends that you return it to an authorized Data I/O Service Center every twelve months for a complete performance evaluation. 3980xpi/3980/3900/2900 User Manual 1-7
Page 1 and 2: 3980 Programming System User Manual
Page 3 and 4: Contents Contents Preface Safety Su
Page 5 and 6: Contents Session 11: Programming a
Page 7 and 8: Contents CRC Default Settings. . .
Page 9 and 10: Figure Page 5-4. Formatted Binary F
Page 11 and 12: Preface Contacting Data I/O Telepho
Page 13 and 14: Safety Summary Terms General safety
Page 15 and 16: 1 Introduction Product Descriptions
Page 17 and 18: External Features Front Panel The f
Page 19: PC Disk Boot Files Disk—3900/2900
Page 23 and 24: 3980xpi Upgrade Kit—3980/3900 Int
Page 25 and 26: Setting Up Connecting to a PC To co
Page 27 and 28: Setting Up 3e. Press Ctrl+R. Select
Page 29 and 30: Setting Up 1a. Connect one end of t
Page 31 and 32: Setting Up After you turn on the pr
Page 33 and 34: Setting Up Pin Functions The functi
Page 35 and 36: Setting Up 3. Install the Base Befo
Page 37 and 38: Setting Up 2. Lift the Base up and
Page 39 and 40: Setting Up 5. Check Self-test Resul
Page 41 and 42: Setting Up 6. Start-up Screen The S
Page 43 and 44: Setting Up 7. Set Up High Speed Dow
Page 45 and 46: Setting Up 8. Install Devices Use t
Page 47 and 48: Setting Up Inserting a PLCC or LCC
Page 49 and 50: Setting Up Inserting a PGA Device i
Page 51 and 52: Setting Up High Profile PPI Adapter
Page 53 and 54: Setting Up QFP Devices Orient pin 1
Page 55 and 56: Setting Up Inserting Other Devices
Page 57 and 58: Setting Up Cleaning Procedure 1. Bl
Page 59 and 60: Setting Up 11. Using the Mass Stora
Page 61 and 62: Getting Started Session 1: Programm
Page 63 and 64: Getting Started 7. The following wi
Page 65 and 66: Getting Started 14. You will be pro
Page 67 and 68: Getting Started 6. From the Setup m
Page 69 and 70: Getting Started Session 2: Navigati
Page 71 and 72:
Getting Started Move the cursor to
Page 73 and 74:
Getting Started Non-fatal error mes
Page 75 and 76:
Getting Started Figure 3-6. Part Nu
Page 77 and 78:
Getting Started Figure 3-8. Keep Cu
Page 79 and 80:
Getting Started Session 5: Loading
Page 81 and 82:
Getting Started To switch between t
Page 83 and 84:
Getting Started 5.Select Load File
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Getting Started Download the File R
Page 91 and 92:
Getting Started Review 4.Read the m
Page 93 and 94:
Getting Started To switch between t
Page 95 and 96:
Getting Started Verify the Device T
Page 97 and 98:
Commands Figure 4-1. Command Tree (
Page 99 and 100:
Commands Parameter Factory Default
Page 101 and 102:
Commands 4. In the Manufacturer fie
Page 103 and 104:
Commands Load Device Load Logic Dev
Page 105 and 106:
Commands Program Device � Set Aut
Page 107 and 108:
Commands Program Memory Device Main
Page 109 and 110:
Commands � Blank Check (Y,N) Enab
Page 111 and 112:
Commands Verify Memory Device Main
Page 113 and 114:
Commands More Commands In general,
Page 115 and 116:
Commands Edit Parameters More Comma
Page 117 and 118:
Commands If you choose E then Selec
Page 119 and 120:
Commands Swapping bytes is useful w
Page 121 and 122:
Commands Not every baud rate works
Page 123 and 124:
Commands � Fill Data Allows you t
Page 125 and 126:
Commands Since the host may not exp
Page 127 and 128:
Commands Programmer ID Keep Current
Page 129 and 130:
Commands Purge 2. When you select t
Page 131 and 132:
Commands Add 7. If you selected a m
Page 133 and 134:
Commands Update Mass Storage More C
Page 135 and 136:
Commands The following parameters a
Page 137 and 138:
Commands Blank Check Electronic Era
Page 139 and 140:
Commands Search Pattern Device Conf
Page 141 and 142:
Commands Command Keystrokes Descrip
Page 143 and 144:
Commands Command Keystrokes Descrip
Page 145 and 146:
Commands Memory Editor Commands Onl
Page 147 and 148:
Commands Data Copy More Commands/Ed
Page 149 and 150:
Commands Save File To load a file i
Page 151 and 152:
Commands Copy File Duplicate Disk 3
Page 153 and 154:
Commands Job File 3. The programmer
Page 155 and 156:
Commands Self-test More Commands/Se
Page 157 and 158:
Commands Upload Data � I/O Addr O
Page 159 and 160:
Commands Compare Data More Commands
Page 161 and 162:
Commands Output To Disk The followi
Page 163 and 164:
Commands The parameters for this co
Page 165 and 166:
Commands Transparent Mode Transpare
Page 167 and 168:
Translation Formats Instrument Cont
Page 169 and 170:
Translation Formats A single data b
Page 171 and 172:
Translation Formats Formatted Binar
Page 173 and 174:
Translation Formats Spectrum Format
Page 175 and 176:
Translation Formats Security_Bit ta
Page 177 and 178:
Translation Formats LOF Format, Cod
Page 179 and 180:
Translation Formats ASCII Octal and
Page 181 and 182:
Translation Formats RCA Cosmac Form
Page 183 and 184:
Translation Formats MOS Technology
Page 185 and 186:
Translation Formats Intel Intellec
Page 187 and 188:
Translation Formats Motorola EXORma
Page 189 and 190:
Translation Formats 03 — Start Re
Page 191 and 192:
Translation Formats The Data Bus Wi
Page 193 and 194:
Translation Formats BNF Rules and S
Page 195 and 196:
Translation Formats JEDEC Full Form
Page 197 and 198:
Translation Formats Fuse Informatio
Page 199 and 200:
Translation Formats The following e
Page 201 and 202:
Translation Formats Functional test
Page 203 and 204:
Translation Formats Item No. of ASC
Page 205 and 206:
Translation Formats Hewlett-Packard
Page 207 and 208:
Translation Formats Intel OMF286 Fo
Page 209 and 210:
Translation Formats Intel Hex-32, C
Page 211 and 212:
Translation Formats Highest I/O Add
Page 213 and 214:
Messages Beginning of file Begin ad
Page 215 and 216:
Messages Disk duplication overwrite
Page 217 and 218:
Messages Insert blank device. Hit r
Page 219 and 220:
Messages OPERATION COMPLETE. Sumche
Page 221 and 222:
Messages Trc init err The programme
Page 223 and 224:
Messages Additional Information The
Page 225 and 226:
Messages Device Programming Error P
Page 227 and 228:
Messages Electronic ID Verify Error
Page 229 and 230:
Messages Probable Cause Solution Ad
Page 231 and 232:
Messages Incompatible User Data Fil
Page 233 and 234:
Performance Verification Accessing
Page 235 and 236:
Performance Verification Figure A-4
Page 237 and 238:
B Computer Remote Control System Se
Page 239 and 240:
Interface Modes Exiting CRC Mode Co
Page 241 and 242:
CRC Commands Description Setting Se
Page 243 and 244:
Summary of Extended CRC Commands Co
Page 245 and 246:
C Keep Current Subscription The Kee
Page 247 and 248:
2. Connect to Keep Current Using th
Page 249 and 250:
D Glossary Action Symbol Address Fo
Page 251 and 252:
Cross Programming Data Bits Data Re
Page 253 and 254:
Filename Fuse Verification Fusemap
Page 255 and 256:
LCC LED Load Data Load Device Logic
Page 257 and 258:
Pin Driver PGA PLCC PLD PROM Progra
Page 259 and 260:
Self-test Serial Set Glossary A bui
Page 261 and 262:
Translation Formats Glossary A form
Page 263 and 264:
Workstation Yield Yield Tally ZIF S
Page 265 and 266:
Index devices, 4-44 peripherals, 2-
Page 267 and 268:
Index Fill Memory, 4-52 Edit Commun
Page 269 and 270:
Index Next Operation Begins At Ille
Page 271 and 272:
Index Output Memory Data, 4-68 Outp
show all

3980xpi Users Manual - Data I/O Corporation

Create successful ePaper yourself

Delete template?

Save as template?