3980xpi Users Manual - Data I/O Corporation

2 Setting Up
This chapter describes how to set up the programmer and get it working with
your equipment. Before you read this chapter, read Chapter 1, Introduction.
Hardware configuration and software installation are described in the following
steps:
1. Choose Your Configuration and Connect the Equipment
Connect to a PC and Use TaskLink . . . . . . . . . . . . . . . . . . . . . . . .2-2
Connect to a PC and Use HiTerm . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Connect to a Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Connect to a Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2. Insert the Boot Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
3. Install the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
4. Turn On the Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
5. Check Self-test Results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16
6. Start-up Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18
7. Set Up High Speed Download (optional) . . . . . . . . . . . . . . . . . . .2-20
8. Install a device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22
9. Learn about preventive maintenance . . . . . . . . . . . . . . . . . . . . .2-32
10. Learn what to do next time . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-35
11. Using the Mass Storage Module (MSM) . . . . . . . . . . . . . . . . . . . .2-36
1. Choose Your Configuration and Connect the Equipment
Choose the configuration you will use to control the programmer and follow the
steps in the appropriate section to connect the equipment.
� Connect to an IBM-compatible PC. To control your programmer, you
can use TaskLink for Windows, TaskLink for DOS or Terminal emulation
software.
Note: Terminal emulation software can be called up from within
TaskLink for Windows or from TaskLink for DOS.
TaskLink Users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
HiTerm Users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
� Connect to a Host, a minicomputer such as a Sun, DEC, or
Apollo workstation. You can use the workstation to control the
programmer and to store data files . . . . . . . . . . . . . . . . . . . . . . .2-5
� Connect to a Terminal, a stand-alone terminal such as the
DEC VT-100, Qume VT-101, and the Wyse WY-30/40/70 family
of terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
3980xpi/3980/3900/2900 User Manual 2-1