certific at e - NOC international
certific at e - NOC international
certific at e - NOC international
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
176 KRW<br />
Zylinderrollenlager<br />
Cylindrical roller bearings<br />
Normen<br />
Zylinderrollenlager, einreihig DIN 5412, Teil 1<br />
Zylinderrollenlager, zweireihig DIN 5412, Teil 4<br />
Toleranzen, Lagerluft<br />
Toleranzen: Radiallager, siehe Abschnitt Lagerd<strong>at</strong>en.<br />
Radialluft: Zylinderrollenlager, siehe Abschnitt<br />
Lagerd<strong>at</strong>en<br />
Käfige<br />
Alle Zylinderrollenlager der Reihen NU10, NU18, NU19,<br />
NU2, NU20, NU22, NU23, NU28, NU29, NU3, NU30,<br />
NU31, NU4, NU60, NN30.. NNU49, NNU60 werden<br />
vorzugsweise mit Messingmassivkäfig ausgeführt.<br />
Massivkäfige liegen vor als<br />
• Kammkäfig, Nachsetzzeichen M<br />
• Fensterkäfig, Nachsetzzeichen MP<br />
• Kammdeckelkäfig, mit Stahlniet warmvernietet,<br />
Nachsetzzeichen M2<br />
• Kammdeckelkäfig, stegvernietet,<br />
Nachsetzzeichen M3<br />
• Kammdeckelkäfig, verschraubt, Nachsetzzeichen<br />
M4 (nur über Bohrungskennziffer 64)<br />
Die Führung des Massivkäfigs im Zylinderrollenlager<br />
wird realisiert durch:<br />
• Wälzkörperführung, ohne weiteres<br />
Nachsetzzeichen<br />
• Außenbordführung, zusätzliches<br />
Nachsetzzeichen A<br />
• Innenbordführung, zusätzliches Nachsetzzeichen B<br />
Winkeleinstellbarkeit<br />
Die modifizierte Linienberührung zwischen Rollen<br />
und Laufbahnen der Zylinderrollenlager verhindert<br />
Kantenspannungen und läßt eine gewisse<br />
Winkeleinstellbarkeit zu. Bei einreihigen<br />
Zylinderrollenlagern darf bei einem Belastungsverhältnis<br />
P/C < 0,2 der Einstellwinkel maximal 4 Winkelminuten<br />
betragen (P = dynamisch äquivalente Belastung [kN],<br />
C = dynamische Tragzahl [kN]).<br />
Die Einbaustellen zweireihiger Zylinderrollenlager dürfen<br />
keine Fluchtfehler aufweisen.<br />
Bauformen<br />
Neben den herkömmlichen Bauformen NU und NJ werden<br />
auch andere Bauformen gefertigt. Stellvertretend<br />
für weitere Bauformen sind einige nachfolgend dargestellt:<br />
Folgende Kombin<strong>at</strong>ionsbezeichnungen sind üblich:<br />
für NU + HJ: NUJ<br />
für NJ + HJ: NH<br />
für WU + HJ: WU..W<br />
Standards<br />
Cylindrical roller bearings, single row, according to DIN<br />
5412, part 1<br />
Cylindrical roller bearings, double row, according to<br />
DIN 5412, part 4<br />
Tolerances, bearing clearance<br />
Tolerances: Radial bearings, see section bearing d<strong>at</strong>a.<br />
Radial clearance: Cylindrical roller bearings, see section<br />
bearing d<strong>at</strong>a.<br />
Cages<br />
All the cylindrical roller bearings of the series NU10,<br />
NU18, NU19, NU2, NU20, NU22, NU23, NU28 NU29,<br />
NU3, NU30, NU31, NU4, NU60NN30.. NNU49, NNU60<br />
are preferably delivered with machined brass cage.<br />
The following machined cages are available:<br />
• Chamber-type cages, letter code M<br />
• Window-type cages, letter code MP<br />
• Comb-type cup cages, hot-riveted steel rivets,<br />
letter code M2<br />
• Comb-type cup cages, spider riveted, letter<br />
code M3<br />
• Comb-type cup cages, bolted, letter code M4<br />
(available only for bore diameter 64 and higher)<br />
The following types of machined cage guidance are<br />
offered for cylindrical roller bearings:<br />
• Roller guidance, no extra letter code<br />
• Outer roller guidance, additional letter code A<br />
• Inner roller guidance, additional letter code B<br />
Angular adjustment<br />
The modified line contact between rollers and races of<br />
cylindrical roller bearings avoids edge tension, and allows<br />
a slight adjustment of the contact angle. The adjusted<br />
contact angle shall not exceed 4 minutes with<br />
a load r<strong>at</strong>io P/C < 0.2 of single row cylindrical roller<br />
bearings. (P = equivalent dynamic load [kN], C = dynamic<br />
capacity [kN]).<br />
The mounting positions of double row cylindrical roller<br />
bearings shall be free of any misalignment.<br />
Design versions<br />
There are not only the standard types NU and NJ, bearings<br />
of other design are manufactured as well. We<br />
quote a few samples of other design here:<br />
The following combin<strong>at</strong>ion specific<strong>at</strong>ions are common:<br />
for NU + HJ: NUJ<br />
for NJ + HJ: NH<br />
for WU + HJ: WU..W