certific at e - NOC international

Tolerances of radial bearings (except tapered roller bearings)
Tolerance class P5 - outer ring
Dimensions in mm
Nominal over 18 30 50 80 120 150 180 250 315 400 500 630 800 1000
outside diameter up to 30 50 80 120 150 180 250 315 400 500 630 800 1000 1250
Tolerances in microns
Deviation ∆ dmp 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-6 -7 -9 -10 -11 -13 -15 -18 -20 -23 -28 -35 -40 -50
Variation V dp
Diameter series 7∙8∙9 6 7 9 10 11 13 15 18 20 23 28 35
0∙1∙2∙3∙4 5 5 7 8 8 10 11 14 15 17 21 26
Variation VDmp 3 4 5 5 6 7 8 9 10 12 14 18
Width variation VCs 5 5 6 8 8 8 10 11 13 15 18 20 25 30
Radial runout Kea 6 7 8 10 11 13 15 18 20 23 25 30 35 50
Variation in inclination SD 2)
Axial runout Sea 8
8
8
8
8
10
9
11
10
13
10
14
11
15
13
18
13
20
15
23
18
25
20
30
30
40
40
55
The width tolerance ∆ Cs is identical with ∆ Bs of the inner ring.
2) The face runout values refer up to deep groove ball bearings and spindle bearings
Tolerances of cylindrical roller bearings (double row)
Tolerance class SP - inner ring
Dimensions in mm
Nominal over 18 30 50 80 120 180 250 315 400 500 630 800 1000
bore diameter up to 30 50 80 120 180 250 315 400 500 630 800 1000 1250
Bore, cylindrical
Tolerances in microns
Deviation ∆ dmp , ∆ ds 0 0 0 0 0 0 0 0 0 0 0 0 0
-6 -8 -9 -10 -13 -15 -18 -23 -27 -30 -40 -50 -65
Variation V dp 3 4 5 5 7 8 9 12 14
Bore, tapered
Deviation ∆ ds +10 +12 +15 +20 +25 +30 +35 +40 +45 +50 +65 +75 +90
0 0 0 0 0 0 0 0 0 0 0 0 0
Variation V dp 3 4 5 5 7 8 9 12 14
+4 +6 +6 +8 +8 +10 +12 +12 +14
Deviation ∆ d1mp -∆ dmp 0 0 0 0 0 0 0 0 0
Width deviation ∆ Bs 0 0 0 0 0 0 0 0 0 0 0 0 0
-100 -120 -150 -200 -250 -300 -350 -400 -450 -500 -750 -1000 -1250
Width variation V Bs 5 5 6 7 8 10 13 15 17 20 30 33 40
Radial runout K ia 3 4 4 5 6 8 8 10 10 12 15 17 20
Axial runout S d 8 8 8 9 10 11 13 15 17 20 23 30 40
Axial runout S ia 8 8 8 9 10 13 15 20 23 25 30 40 50
Tolerances of cylindrical roller bearings (double row) in machine tools
Tolerance class SP -outer ring
Dimensions in mm
Nominal over 18 30 50 80 120 150 180 250 315 400 500 630 800 1000
outside diameter up to 30 50 80 120 150 180 250 315 400 500 630 800 1000 1250
Tolerances in microns
Deviation ∆ Dmp ,∆ Ds 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 7 -7 -9 -10 -11 -13 -15 -18 -20 -23 -28 -35 -40 -50
Variation V Dp 4 5 5 6 7 8 9 10 12 14 18
Radial runout Kea 5 5 5 6 7 8 10 11 13 15 17 20 25 30
Variation in inclination S D 8 8 8 9 10 10 11 13 13 15 18 20 30 40
Axial runout S ea 8 8 10 11 13 14 15 18 20 23 25 30 40 55
The width tolerance ∆ Cs and V Cs are identical with ∆ Ss and V Bs of the inner ring.
KRW 91