Product Description XI/ON - Eaton Automation

More documents

Recommendations

Info

XI/ON: Gateways for Modbus TCP 8 Guidelines for Electrical Installation 8.4 Shielding of cables Shielding is used to prevent interference from voltages and the radiation of interference fields by cables. Therefore, use only shielded cables with shielding braids made from good conducting materials (copper or aluminum) with a minimum degree of coverage of 80 %. The cable shield should always be connected to both sides of the respective reference potential (if no exception is made, for example, such as high-resistant, symmetrical, analog signal cables). Only then can the cable shield attain the best results possible against electrical and magnetic fields. A one-sided shield connection merely achieves an isolation against electrical fields. Attention When installing, please pay attention to the following... – the shield should be connected immediately when entering the – system, – the shield connection to the shield rail should be of low – impedance, – the stripped cable-ends are to be kept as short as possible, – the cable shield is not to be used as a bonding conductor. If the data cable is connected via a SUB-D connector, the shielding should never be connected via pin 1, but to the mass collar of the plug-in connector. The insulation of the shielded data-cable should be stripped and connected to the shield rail when the system is not in operation. The connection and securing of the shield should be made using metal shield clamps. The shield clamps must enclose the shielding braid and in so doing create a large surface contact area. The shield rail must have a low impedance (for example, fixing points of 10 to 20 cm apart) and be connected to a reference potential area. The cable shield should not be severed, but routed further within the system (for example, to the switchgear cabinet), right up to the interface connection. 170 M001973-01, 07/2007
XI/ON: Gateways for Modbus TCP 8 Guidelines for Electrical Installation Note Should it not be possible to ground the shield on both sides due to switching arrangements or device specific reasons, then it is possible to route the second cable shield side to the local reference potential via a capacitor (short connection distances). If necessary, a varistor or resistor can be connected parallel to the capacitor, to prevent disruptive discharges when interference pulses occur. A further possibility is a double-shielded cable (galvanically separated), whereby the innermost shield is connected on one side and the outermost shield is connected on both sides. M001973-01, 07/2007 171
Page 1 and 2:
Product Description XI/ON Gateways
Page 3 and 4:
XI/ON: Gateways for Modbus TCP Safe
Page 5 and 6:
XI/ON: Gateways for Modbus TCP Tabl
Page 7 and 8:
XI/ON: Gateways for Modbus TCP Tabl
Page 9 and 10:
XI/ON: Gateways for Modbus TCP 1 Ab
Page 11 and 12:
XI/ON: Gateways for Modbus TCP 1 Ab
Page 13 and 14:
XI/ON: Gateways for Modbus TCP 2 XI
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
XI/ON: Gateways for Modbus TCP 3 Et
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
XI/ON: Gateways for Modbus TCP 4 Te
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
XI/ON: Gateways for Modbus TCP 5 Im
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
XI/ON: Gateways for Modbus TCP 6 Ap
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120: XI/ON: Gateways for Modbus TCP 6 Ap
Page 149 and 150: XI/ON: Gateways for Modbus TCP 7 Gu
Page 169: XI/ON: Gateways for Modbus TCP 8 Gu
Page 213 and 214: XI/ON: Gateways for Modbus TCP 10 G
Page 221 and 222:
XI/ON: Gateways for Modbus TCP 10 G
Page 223 and 224:
XI/ON: Gateways for Modbus TCP 11 I
show all

Product Description XI/ON - Eaton Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?