Electrical Power Systems

More documents

Recommendations

Info

= 0.008993 m/km. Capacitance of Transmission Lines 73 Example 3.11: ind out the capacitance per km to neutral of the three phase line as shown in ig. 3.19. The lines are regularly transposed. The radius of each subconductor is r = 0.5 cm. Solution. Applying eqn. (3.34), \ C an = HG Can = 00242 . log D eq D s ig. 3.19 I KJ m/km 1 3 b g b g { } Ds = r´ 2r ´ 2r 3 = 0 . 0 5 ´ 4 = 0.00793 m b g = 6.3 m 1 Deq = 5´ 5 ´ 10 3 HG 00242 . 63 . log 0. 00793 I KJ m/km \ C an = 0.00834 m/km Ans. Example 3.12: ind out the capacitance per km to neutral of the three phase line as shown in ig. 3.20. The lines are regularly transposed. The radius of each conductor is r = 0.5 cm Solution. Applying eqn. (3.34) Can = 00242 . ig. 3.20 log D eqI HG Ds KJ m/km 1 b ´ ´ g3m = 6.3 m D eq = 5 5 10 1 3
74 Electrical Power Systems 1 4 e j = 1.834 r = 1.834 × 0.005 m Ds = r ´ 2r ´ 2 2r ´ 2r C an = = 0.00917 m. HG 00242 . 63 . log 0. 00917 \ C an = 0.00853 m/km. I KJ m/km Example 3.13: Derive an expression for the charge value per meter length of conductor a of an untransposed three phase line as shown in ig. 3.21. The applied voltage is balanced three phase. Also find out the charging current of phase a. Solution. Taking phase a as reference Van = || V º 3 0 Vab = | V| 30º Vbc = | V| -90º Vca = | V| 150º \ Vac = | V| -30º Applying eqn. (3.5) V ab = V ac = ig. 3.21 L NM O QP = Lqa NM 2D + qb r D + c D O 2 QP q r D 1 D r D qa ln + qb ln + qc ln | V| 30º ...(i) 2pÎ r d 2D o 1 2 pÎ o ln ln ln = | V| -30º ...(ii) \ qa + qb + qc = 0 qb = – (qa + qc) ...(iii) rom eqns. (i) and (iii), we get
Page 3:
This page intentionally left blank
Page 6 and 7:
To My Wife Shanta Son Debojyoti and
Page 8 and 9:
Preface During the last fifty years
Page 10 and 11:
Contents Preface vii 1. Structure o
Page 12 and 13:
Contents xi 9. Symmetrical Componen
Page 14 and 15:
Structure of Power Systems and ew O
Page 16 and 17:
1.2 REASONS OR INTERCONNECTION Stru
Page 18 and 19:
Page 20 and 21:
Case-1: If P 1 = P 2 = P 3 = ... =
Page 22 and 23:
Load factor, L = Maximum load = 3 M
Page 24 and 25:
\ LD = 1 MW (c) rom eqn.(1.13), coi
Page 26 and 27:
Case-2: Very short lasting peak. He
Page 28 and 29:
1.9 DISADVANTAGES O LOW POWER ACTOR
Page 30 and 31:
Page 32 and 33:
Resistance and Inductance of Transm
Page 34 and 35:
2.4.1 Internal Inductance igure 2.1
Page 36 and 37: Resistance and Inductance of Transm
Page 38 and 39: Therefore, we can write L 1 = L 11
Page 40 and 41: L a = 0.4605 n log R S| T| Resistan
Page 42 and 43: L = 0.4605 L Resistance and Inducta
Page 44 and 45: =(2Dd 1 · 2Dd 1) 1/4 = (2 Dd 1) 1/
Page 46 and 47: Solution. The distances from strand
Page 50 and 51: Solution: Using eqn. (2.14), Hx = I
Page 52 and 53: = 0.4605 log 6611 . 04 . Resistance
Page 58 and 59: Since from symmetry D b1= D b2, l 1
Page 60 and 61: \ D m = D D D D Resistance and Indu
Page 62 and 63: dg 1 2 \ Dsa = 0. 7788 ´ 0. 015 ´
Page 66 and 67: Capacitance of Transmission Lines 5
Page 68 and 69: V Ki = 1 pÎ N å q m 2 o m = 1 3.3
Page 70 and 71: Similarly for the 2nd transposition
Page 74 and 75: C an = log R S| T| 00242 . 1 1 1 1
Page 76 and 77: \ V12 = q ln pÎo \ C 12 = q \ C 12
Page 78 and 79: I chg = jw C anV LN \ |I chg| = w C
Page 80 and 81: Line length is 200 km. \ Can (total
Page 82 and 83: Now applying eqn. (3.7), we have C
Page 92 and 93: Synchronous Machine: Steady State a
Page 98 and 99: \ V = 138 Using eqn. (4.18), . 3 =
Page 100 and 101: om ig. 4.6, Synchronous Machine: St
Page 106 and 107: \ i asy max = from which Synchronou
Page 108 and 109: Postfault voltage Synchronous Machi
Page 110 and 111: or the reference phase a, E a = (Z
Page 112 and 113: 5.3 THE PER-UNIT (pu) SYSTEM Power
Page 114 and 115: Power System Components and Per Uni
Page 118 and 119: Z L (pu) = Z L (ohm) (. 08+ j 03 .)
Page 126 and 127: \ VL (pu) = 0. 2033 - 76. 68° pu P
Page 128 and 129: Base impedance for the load is ( )
Page 130 and 131: Now we can write, \ |I| cos f = P |
Page 136 and 137:
Power System Components and Per Uni
Page 138 and 139:
This is a simple series circuit. Th
Page 140 and 141:
Eqns (6.15) and (6.17) can be writt
Page 142 and 143:
Characteristics and Performance of
Page 144 and 145:
om eqn. (6.6), Characteristics and
Page 146 and 147:
as: \ |V S| = 145.13 kV. \ Sending
Page 148 and 149:
Page 150 and 151:
Sending end power factor angle = 8.
Page 152 and 153:
\ I R = V R = 208 Characteristics a
Page 154 and 155:
6.6 VOLTAGE WAVES Characteristics a
Page 156 and 157:
Page 158 and 159:
6.9 ERRANTI EECT Characteristics an
Page 160 and 161:
Load low Analysis 7.1 INTRODUCTION
Page 162 and 163:
Applying KCL to the independent nod
Page 164 and 165:
y 10 = y 20 = y 30 = y13 ¢ y12 ¢
Page 166 and 167:
\ V i = 1 Y ii L NM P - jQ i i * Vi
Page 168 and 169:
n 2 i ii ii ik i k ik k i \ Pi - jQ
Page 170 and 171:
Load low Analysis 157 ig. 7.6: P-re
Page 172 and 173:
Load low Analysis 159 are permitted
Page 174 and 175:
1 1 y13 = y31 = = = ( 10 - j30) Z (
Page 176 and 177:
(1) \ V3 = 10011 . - 2. 06° After
Page 178 and 179:
Load low Analysis 165 Using eqn. (7
Page 180 and 181:
Load low Analysis 167 \ Q 2 = -|V 2
Page 182 and 183:
|V 1| = 1.05,|V 2| = 1.0,|V 3| (1)
Page 184 and 185:
\ L NM e j ( 0) ( 0) ( 0) 1 1 1 2 n
Page 186 and 187:
( p) p The terms DPi and DQi Load l
Page 188 and 189:
Load low Analysis 175 P2 = -35.77
Page 190 and 191:
(1) P2( cal ) = -2.62 (1) P3( cal )
Page 192 and 193:
Load low Analysis 179 Use deoupled
Page 194 and 195:
0 Dd2 \ Dd3 0 ( ) ( ) NM \ 0 Dd2 L
Page 196 and 197:
Assuming q ik - d i + d k » d ik,
Page 198 and 199:
Table 7.4: Line impedances BUS code
Page 200 and 201:
Symmetrical ault 187 is drawing 10
Page 202 and 203:
\ X TH = ig. 8.4: Thevenin equivale
Page 204 and 205:
ig. 8.5: Circuit diagram of Example
Page 206 and 207:
= | Vo| | Vo| | Z| ´ × (MVA) Base
Page 208 and 209:
\ 1 - V 1f = j0.14 × (-j4.165) \ V
Page 210 and 211:
Base current I B = Per unit reactan
Page 212 and 213:
Symmetrical ault 199 Example 8.9: T
Page 214 and 215:
Solution: Let Base MVA = 12 Base Vo
Page 216 and 217:
Solution: Let Base MVA = 100 Base V
Page 218 and 219:
Therefore, current to be interrupte
Page 220 and 221:
Circuit model under fault condition
Page 222 and 223:
Symmetrical ault 209 Example 8.16:
Page 224 and 225:
8.4 SHORT CIRCUIT ANALYSIS OR LARGE
Page 226 and 227:
om equations. (8.9) and (8.10), we
Page 228 and 229:
Using equation (8.14), Z BUS = L NM
Page 230 and 231:
Symmetrical ault 217 Solution: Inje
Page 232 and 233:
Hence, new Z = BUS 8.6.3 Type-3 Mod
Page 234 and 235:
or L V 1 V M NM 2 V 0 n O QP = L ol
Page 236 and 237:
Solution: (a) Using equation (8.11)
Page 238 and 239:
Symmetrical ault 225 8.7 ig. 8.31 s
Page 240 and 241:
has the following properties R S| T
Page 242 and 243:
T stands for transpose. Using eqn.
Page 244 and 245:
Using eqn.( 2.46) as given in Chapt
Page 246 and 247:
Also I n = I a + I b + I c Using eq
Page 248 and 249:
Symmetrical Components 235 ig. 9.4:
Page 250 and 251:
Symmetrical Components 237 (b) - co
Page 252 and 253:
Solution: I a + I b + I c = 0, I a
Page 254 and 255:
Also note that I ab1 = I a1 3 30°
Page 256 and 257:
Base voltage of transmission line 1
Page 258 and 259:
Symmetrical Components 245 Example
Page 260 and 261:
Symmetrical Components 247 Example
Page 262 and 263:
9.5 Draw the zero-sequence network
Page 264 and 265:
Unbalanced ault Analysis 251 Assumi
Page 266 and 267:
The symmetrical components of the f
Page 268 and 269:
Unbalanced ault Analysis 255 The bo
Page 270 and 271:
ig. 10.9: Two conductors open. Unba
Page 272 and 273:
Z 1 = j0.691 0.23 ´ 0. 691+ 0. 23
Page 274 and 275:
Unbalanced ault Analysis 261 Exampl
Page 276 and 277:
\ 3 ´ 1.0 ´ j0.4 j0.3 ´ j0.4 + j
Page 278 and 279:
Denominator of eqns. (i) and (ii) Z
Page 280 and 281:
Hence, rom eqn. (i), V b = V c Unba
Page 282 and 283:
ig. 10.18 shows the sequence networ
Page 284 and 285:
\ V b = E a = 3752.8 0° 1763 . - 3
Page 286 and 287:
Unbalanced ault Analysis 273 ig. 10
Page 288 and 289:
Unbalanced ault Analysis 275 10.4 A
Page 290 and 291:
where J = moment of inertia of roto
Page 292 and 293:
Power System Stability 279 Pi - Pe
Page 294 and 295:
Power System Stability 281 (a) ind
Page 296 and 297:
On a per-phase basis, power at the
Page 298 and 299:
x eq = 0.25 + 0.15 + 02 . ´ 02 . 0
Page 300 and 301:
Power System Stability 287 system.
Page 302 and 303:
Power System Stability 289 or P i (
Page 304 and 305:
\ d1 Pi (dc - d0 ) = z Pmax dc sin
Page 306 and 307:
dcr z 1 d0 cr zbPi-Bgdd d dm = C -
Page 308 and 309:
We know, K1 = Pmax In ig. 11.14, P
Page 310 and 311:
Solution: Prefault operation x A =
Page 312 and 313:
\ cosd cr = 0.654 Power System Stab
Page 314 and 315:
Similarly, the change in the power
Page 316 and 317:
d (2) = d (1) + Dd (2) = 17.855 + 1
Page 318 and 319:
ig. 11.19: Sample network of 11.4.
Page 320 and 321:
Automatic Generation Control: Conve
Page 322 and 323:
12.4 ISOCHRONOUS GOVERNOR Automatic
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Where D = PL = constant. f Theref
Page 330 and 331:
Page 332 and 333:
\ T p = 32 3 sec. Automatic Generat
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
om ig. 12.20, state-variable equati
Page 342 and 343:
The area control error for area-1 a
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Automatic Generation Control in a R
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Corona 357 air around the conductor
Page 372 and 373:
14.4 POTENTIAL GRADIENT OR THREE-PH
Page 374 and 375:
Similarly, G b = G c = r r V bn ln
Page 376 and 377:
Corona 363 In the above expressions
Page 378 and 379:
P c = 2.1f HG log 10 Vn DI HG r K
Page 380 and 381:
Solution: rom eqn. (14.38), air den
Page 382 and 383:
\ V 0 = 110.15 KV(rms) V n = 220 3
Page 384 and 385:
\ W = 55 ´ b69. 28 - 57g 2 635 . -
Page 386 and 387:
Analysis of Sag and Tension 15.1 IN
Page 388 and 389:
where Dl = l0. DT MA DT = T1 - T0 T
Page 390 and 391:
when x = L l , s = 2 2 , \ l 2 = H
Page 392 and 393:
or approximately, 2 d = wL 8H ig. 1
Page 394 and 395:
Squaring eqn. (15.37), we get, s 2
Page 396 and 397:
under the action of T, H and wx. or
Page 398 and 399:
\ T max = 572.59 kg (d) rom eqn. (1
Page 400 and 401:
ig. 15.6: Case of negative x 1. Ana
Page 402 and 403:
where Analysis of Sag and Tension 3
Page 404 and 405:
or 1-meter length of conductor, Ana
Page 406 and 407:
(f ) Vertical sag = dcos q cos q =
Page 408 and 409:
Analysis of Sag and Tension 395 = 0
Page 410 and 411:
Analysis of Sag and Tension 397 Ass
Page 412 and 413:
Analysis of Sag and Tension 399 Dis
Page 414 and 415:
Total weight of the conductor = wl
Page 416 and 417:
Analysis of Sag and Tension 403 Whe
Page 418 and 419:
Optimal System Operation 16.1 INTRO
Page 420 and 421:
Optimal System Operation 407 where
Page 422 and 423:
Optimal System Operation 409 2. The
Page 424 and 425:
Complete algorithm is given below:
Page 426 and 427:
DP g1 = Î 2 DP g2 = Î 2 Using Tay
Page 428 and 429:
Optimal System Operation 415 Equati
Page 430 and 431:
\ 2 C2 = 0.18 Pg2 + 32 Pg2 + K2 Whe
Page 432 and 433:
Optimal System Operation 419 Equati
Page 434 and 435:
DP L = rom eqns (16.36) and (16.39)
Page 436 and 437:
Optimal System Operation 423 Now we
Page 438 and 439:
Optimal System Operation 425 The pr
Page 440 and 441:
Example 16.6: Consider Ex-16.5, wit
Page 442 and 443:
\ DP g (l) = 264.1657 MW rom eqn. (
Page 444 and 445:
\ (4) 2 2 P = 0.00005 × (188.95) +
Page 446 and 447:
Optimal System Operation 433 The te
Page 448 and 449:
\ Also d P 3 d 2 P 3 3 =- G 32 si
Page 450 and 451:
Let the current in line K be I K1.
Page 452 and 453:
+ HG I K Optimal System Operation
Page 454 and 455:
Now, \ V1 = 1.198 14. 5º, \d1 = 14
Page 456 and 457:
Optimal System Operation 443 B 11 =
Page 458 and 459:
Z 1 = (0.03 + j0.12)pu; I 1 = (1.3
Page 460 and 461:
Objective Questions Objective Quest
Page 462 and 463:
Objective Questions 449 26. or a de
Page 464 and 465:
Objective Questions 451 56. Peak lo
Page 466 and 467:
82. Inductance of a conductor due t
Page 468 and 469:
Objective Questions 455 108. In ter
Page 470 and 471:
Objective Questions 457 137. In a p
Page 472 and 473:
Objective Questions 459 (c) are var
Page 474 and 475:
203. A system is said to be effecti
Page 476 and 477:
Answers of Objective Questions 1. (
Page 478 and 479:
Bibliography Bibliography 465 1. O.
Page 480 and 481:
Index accelerating (or decelerating
Page 482 and 483:
methods for voltage control 115 mul
show all

Electrical Power Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?