Toshiba iES32 Installation Manual.pdf

Stratagy ES4, ES80, ES96, ES96R Installation
Step 11: Connect Voice Board(s) to Telephone Lines
DB37 Male Connector Pinout
(D/160SC-LS End)
RJ21X Amphenol Female Connector Pinout
Pin Number
Signal
Signal
1 Tip 1
Ring 3 20 2 Tip 2
Ring 4 21 3 Tip 3
Ring 5 22 4 Tip 4
Ring 6 23 5 Tip 5
Ring 7 24 6 Tip 6
Ring 8 25 7 Tip 7
Ring 9 26 8 Tip 8
Ring 10 27 9 Tip 9
Ring 11 28 10 Tip 10
Ring 12 29 11 Tip 11
Ring 13 30 12 Tip 12
Ring 14 31 13 Tip 13
Ring 15 32 14 Tip 14
Ring 16 33 15 Tip 15
Unused 34 16 Tip 16
Unused 35 17 Unused
Unused 36 18 Ring 1
Ground 37 19 Ring 2
Pin Number
Signal
Signal
Station 1 Ring 1 26 Station 1 Tip
Station 2 Ring 2 27 Station 2 Tip
Station 3 Ring 3 28 Station 3 Tip
Station 4 Ring 4 29 Station 4 Tip
Station 5 Ring 5 30 Station 5 Tip
Station 6 Ring 6 31 Station 6 Tip
Station 7 Ring 7 32 Station 7 Tip
Station 8 Ring 8 33 Station 8 Tip
Station 9 Ring 9 34 Station 91 Tip
Station 10 Ring 10 35 Station 10 Tip
Station 11 Ring 11 36 Station 11 Tip
Station 12 Ring 12 37 Station 12 Tip
Station 13 Ring 13 38 Station 13 Tip
Station 14 Ring 14 39 Station 14 Tip
Station 15 Ring 15 40 Station 15 Tip
Station 16 Ring 16 41 Station 16 Tip
Station 17 Ring 17 42 Station 17 Tip
Station 18 Ring 18 43 Station 18 Tip
Station 19 Ring 19 44 Station 19 Tip
Station 20 Ring 20 45 Station 20 Tip
Station 21 Ring 21 46 Station 21 Tip
Station 22 Ring 22 47 Station 22 Tip
Station 23 Ring 23 48 Station 23 Tip
Station 24 Ring 24 49 Station 24 Tip
25 50
Figure 2-17 Cable Connector Pinouts
Connect the D/160SC-LS to the LSI 1459/RJ21X
Important!
This procedure should be used when connecting the D/160SC-LS board to CO
line(s). If you are connecting the board to a PBX, see “Connect the D/160SC-LS
Using an Adapter Cable and Punch-down Blocks” on page 2-15 for instructions.
1. Connect the LSI 1459 adapter to
the RJ21X jack with the cable
packaged with the LSI 1459
adapter (Figure 2-18).
2. Connect the D/160SC-LS board
to the LSI 1459 adapter with the
D/160SC-LS adapter cable.
Insert the 37-pin cable end into
the DB-37 connector on the
board bracket. Insert the 50-pin
cable end into the connector on
D/160SC-LS
Board
Figure 2-18
D/160SC-LS Adapter Cable
LSI 1459
Adapter
Cable packaged with
LSI 1459 Adapter
LSI 1459/Station Adapter Connection
the RJ21X jack. See Figure 2-17 for connector pinout diagram.
3. Connect the LSI 1459 Adapter to a CO line using a RJ21X connector and cross connect.
RJ21X
4745
2-16 Stratagy ES I&M 06/02