Telemecanique Altivar 56 manual - Northern Industrial

L1 L2 L3TelemecaniqueT1 T2 T3L1 L2 L3TelemecaniqueT1 T2 T3NCNCNCNCBefore Servicing theBefore Servicingselected:Failure to observe these precautions will result in death orserious injury.234Drive Controller:Disconnect All Power.Place a "Do Not Turn On" label on Drive Controller.Lock Disconnect in Open Position.This equipment must be installed andserviced only by qualified electricalpersonnel.Turn off all power supplying thisequipment before working on or insideequipment.Always use a properly rated voltagesensing device to confirm power is off.Replace all devices, doors, and coversbefore turning on power to this equipment.Basic Power ConverterPerform all functions listed above.Measure Voltages at Disconnect Output to verify they are zero.Wait 1 minute to allow DC Bus to discharge, verify no voltage ispresent.Remove Line Fuses labeled FU1, FU2 and FU3 with toolprovided.Replace Cover, then close the disconnect.Before Servicing theBefore Servicingselected:Drive Controller:Disconnect All Power.Place a "Do Not Turn On" label on Drive Controller.Lock Disconnect in Open Position.Basic Power Converter98This equipment must be installed andserviced only by qualified electricalpersonnel.Turn off all power supplying thisequipment before working on or insideequipment.Always use a properly rated voltagesensing device to confirm power is off.Replace all devices, doors, and coversbefore turning on power to this equipment.Perform all functions listed above.Measure Voltages at Disconnect Output to verify they are zero.Wait 1 minute to allow DC Bus to discharge, verify no voltage ispresent.Remove Line Fuses labeled FU1, FU2 and FU3 with toolprovided.Replace Cover, then close the disconnect.Failure to observe these precautions will result in death orserious injury.23498ONTRAVAIL DELAYTELEMECANIQUEwhen Bypass iswhen Bypass isL1 L2 L3XXXXX-XXX-XX1,5-30sXXXXX-XXX-XX53 NO 63 NO53 NO 63 NOTELEMECANIQUE54 NO 64 NO54 NO 64 NOT1 T2 T3NCNCL1 L2 L3TELEMECANIQUET1 T2 T3Telemecanique2326TESTA322998 NO 9795 NC 96T1T2RA ESETNCNCBulletin No. 50006-519-01BDecember 1996Chapter 6 — Class 8839 ALTIVAR 56 Combination DevicesTerminal Strip LocationsTERMINAL STRIPLOCATIONSFigures 74 through 78 show terminal strip locations for Class 8839 ALTIVAR 56combination devices. Tables 48 through 51 list wire size and torque requirements.NOTE: Typicaldevice shownwith options.DANGERHAZARD OF ELECTRIC SHOCK OR BURNLINEL1, L2, L3(SW2)13521DRIVE ISOLATION HAZARDLC1D251001ON24622Fuse BlockFU1FU2FU3OFFLOADHAND1010OPENOFFMAINSAUTO567CLOSEControlTerminals1 - 16(QW1, QW2)12345678910111213141516SPTST1 T2 T31718192021222324252627ControlTerminals17 - 27 (SW1)T1, T2, T3(SW2)GNDGNDFigure 74: Terminal Strip Locations for 1 - 50 hp VT & 1 - 40 hp VTLN, 460 V;1 - 25 hp VT & VTLN, 208/230 V (Power Circuit W)NOTE: Typicaldevice shownwith options.Fuse Block121LC101D25102346522DANGERHAZARD OF ELECTRIC SHOCK OR BURNDRIVE ISOLATION HAZARDFU1 FU2 FU3LINE LOADONOFFL1, L2, L3(SW2)HAND1010AFCOFFOFFAUTO567BYPASSControlTerminals1 - 15(QW1, QW2)1234456789101112131415SPTS1LC1DXX023LA4 DT 2U01LC1DXX0LA1DNXXLA1DNXX45621221243LR2DXX01222 4 6 T356STOP21161718192021222324252627282930313233ControlTerminals16 - 33(SW1)T1, T2, T3(SW2)GNDGNDFigure 75: Terminal Strip Locations for 1 - 50 hp VT & 1 - 40 hp VTLN, 460 V;1 - 25 hp VT & VTLN, 208/230 V (Power Circuit Y or Z)© 1996 Square D All Rights Reserved131ηττπ://νιχοντρολσ.χοm