Telemecanique Altivar 56 manual - Northern Industrial

More documents

Recommendations

Info

Bulletin No. 50006-519-01BDecember 1996Chapter 2 — WiringUsing the Relay Outputs (J1)USING THE RELAYOUTPUTS (J1)The ALTIVAR 56 drive controller has two voltage-free Form C relay outputcontacts (see Figure 16). The contacts have the following characteristics:• Minimum voltage: +24 VDC; minimum current: 10 mA• Maximum voltage: +30 VDC; maximum current: 2 A• 120 VAC: maximum current 2 A• 220 VAC: maximum current 1 A• R1 is the drive controller fault relay. It is not programmable.R1R1R2R2R1AR1C R1B R2A R2C R2B+ –Customer SuppliedVoltageCustomerSuppliedFigure 16: Relay OutputsContact state is shown with drive controller deenergized. Relay contact outputscan be assigned to other functions than those set at the factory. Factory settings arelisted in Table 16 on page 34. For information on other functions, refer to Chapter 5.Maximum recommended fuse type and rating is Bussmann FNQ-2 or equivalent.REMOVAL OF CL1,CL2 JUMPERSJumpers CL1 and CL2 are factory installed. If separate control power is required,these jumpers must be removed. To remove jumpers, use the following procedure:ATV56U41N4 to D12N4 and ATV56U41M2 to U90M2 drive controllers: Loosen theCL1 and CL2 screws and the L1 and L2 screws. Remove captive jumper wireassembly.ATV56D16N4 to D79N4 and ATV56D12M2 to D46M2 drive controllers:1. Loosen the front screws only (see Figure 17).CL1 CL2Front screwsPull jumper straight outSleeveFigure 17: CL1, CL2 Jumper Removal2. Using a pair of needle nose pliers, grasp the jumpers and pull straight out.The sleeve on the bottom terminal should remain.3. Connect separate control power to the top terminals. DO NOT makeconnections to the bottom terminals which contain the sleeves. Leave thebottom terminals open circuited.4. Tighten the front screws to secure the connections.© 1996 Square D All Rights Reserved27ηττπ://νιχοντρολσ.χοm
Chapter 2 — WiringBulletin No. 50006-519-01BControl Circuit Diagrams December 1996CONTROL CIRCUITDIAGRAMSThis section contains wiring diagrams for 2- and 3-wire control circuits. Operationof 2- and 3-wire control is explained in Chapter 5.3-Wire ControlExternalControlPower[1]F11EquipmentF10L3L2L1F1-F3STOP0-20 mA4-20 mAR1+ –InternalControlPowerL3L2L1F1-F3CL2CL1L3L2L1+24KeypadConnectorLOP LO2LI4LI3LO1 COM AO2LI2 LI1A1AO1 COMAI2 +10AI1R2C R2A R2BCOMCL2 CL1L3L2W/T3 U/T1R1C R1A R1B V/T2L1PBPA+–[1]Add F10 and F11 fuses if tap conductor protection is required. The CL1 and CL2 inputs of all ATV56 drive controllers are internally protected and require no external fusing.AHzW1 V1M13øU1Figure 18: Recommended 3-Wire Control Circuit DiagramFigure 18 is the recommended 3-wire control circuit diagram. It shows how toconnect a branch circuit disconnect device and protective fusing to the drivecontroller. Additional sequencing logic may be required. Refer to Tables 11 to 15 onpages 30-32 for additional equipment required. The drive controller is factory setfor 2-wire control. To set for 3-wire control, refer to Chapter 5.2-Wire ControlExternalControl PowerEquipment[1] F11 F10L3L2L1F1-F3RUNENABLE0-20 mA4-20 mAR1+ –InternalControlPowerL3L2L1F1-F3CL2CL1L3L2L1+24KeypadConnectorLOP LO2LI4LI3LI2A1LI1LO1 COM AO2 AO1 COMAI2+10AI1R2C R2A R2BCOMCL2 CL1L3L2W/T3 U/T1R1C R1A R1B V/T2L1PBPA+–[1]Add F10 and F11 fuses if tap conductor protection is required. The CL1 and CL2 inputs of all ATV56 drive controllers are internally protected and require no external fusing.AHzW1 V1M13øU1Figure 19: 2-Wire Control Circuit DiagramFigure 19 is a 2-wire control circuit diagram. It shows how to connect a branchcircuit disconnect device and protective fusing to the drive controller. Additionalsequencing logic may be required. See Tables 11 to 15 on pages 30-32 for additionalequipment required.28 © 1996 Square D All Rights Reservedηττπ://νιχοντρολσ.χοm
Page 1 and 2: Instruction Bulletin50006-519-01BDe
Page 3 and 4: DANGERHAZARDOUS VOLTAGE• Read and
Page 5: ALTIVAR 56 Fan and Pump Drive User
Page 8 and 9: Bulletin No. 50006-519-01BDecember
Page 28 and 29: AI2-UAI2-IAI2-UAI2-IAI2-UAI2-IAI2-U
Page 52 and 53: AI2-UAI2-IAI2-UAI2-IBulletin No. 50
Page 68 and 69: Bulletin No. 50006-519-01BChapter 5
Page 86 and 87:
Bulletin No. 50006-519-01BChapter 5
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Bulletin No. 50006-519-01BDecember
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
AUTOOFFHAND234510671098AFCOFFBYPASS
Page 136 and 137:
HANDOFFAUTO241350678OPENMAINSCLOSEF
Page 138 and 139:
Page 140 and 141:
L1 L2 L3TelemecaniqueT1 T2 T3L1 L2
Page 142 and 143:
53 NO 61 NC 71 NO 83 NCTelemecaniqu
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Bulletin No. 50006-519-01BAppendix
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Telemecanique Altivar 56 manual - Northern Industrial

Create successful ePaper yourself

Delete template?

Save as template?