Telemecanique Altivar 56 manual - Northern Industrial

More documents

Recommendations

Info

Bulletin No. 50006-519-01BDecember 1996Chapter 5 — ConfigurationKeypad DisplayFunction KeysKey CoverSTOP KeyUse the function keys to program the drive controller or issue commands.Operation of the function keys depends on whether the drive controller is inTerminal Command or Keypad Command mode.In Terminal Command (drive controller receives its Run, Stop, and ReferenceFrequency signals from the drive controller terminal strip) the function keysoperate as follows:• F1 calls up the Help menu• F2 returns to the Display Mode screen (page 53 and page 55), unless set forTerminal/Keypad switching in the 5→Keypad Configuration menu• F3 functions as a jump keyTo jump directly to a menu, press F3. A window will appear. Enter the menu’sindex number and press ENT. The display will jump directly to that menu. Indexnumbers are found in the upper left corner of the display for each menu, and arealso listed in Table 22 on page 57. Throughout this <strong>manual</strong>, menu names arepreceded by their index numbers. For example, in a reference such as“1→Parameter Setting,” “1” is the index number for the Parameter Setting menu.In Keypad Command (drive controller receives its Run, Stop and ReferenceFrequency signals from the keypad display). The functions of the keys are:• F1 Resets the drive controller after a fault.• F2 Scrolls through the displays.• F3 Not assigned (No functionality).Terminal Command and Keypad Command are described further in the5→Keypad Configuration menu section (page 64).A plastic cover is factory-installed over the RUN and STOP keys. For access toRUN and STOP keys and local command of drive controller, this cover must beremoved. See Figure 32 on page 52. The key cover can be re-installed to cover RUNand STOP keys.The STOP key, active in Terminal and Keypad Command modes, commandsnormal stop of the motor. The motor follows ramp as determined by selecteddeceleration time.WARNINGINABILITY TO INITIATE STOP• With the key cover removed, the STOP key is enabled and active in both TerminalCommand and Keypad Command modes.• When the key cover is installed, the STOP key is not accessible. Verify thatappropriate system STOP functions are in place when the STOP key is not accessible.Failure to follow these instructions can result in death, serious injury, orequipment damage.© 1996 Square D All Rights Reserved51ηττπ://νιχοντρολσ.χοm
Chapter 5 — ConfigurationBulletin No. 50006-519-01BKeypad Display December 1996RUN KeyThe RUN key commands the motor to run when the drive controller is in KeypadCommand mode. The motor follows the ramp determined by the selectedacceleration time. LI1 (Run Enable) on J12 must be high for the RUN key tocommand the motor.LI1 (Run Enable)Run keyStop key101010Motor SpeedFigure 29: Run Timing DiagramKeypad DisplayConnectionsSub D 9-pin connector for connection to thedrive controller.• For remote handheld use, connect terminalwith a 3-meter cable (part # VW3-A66311) or2-meter cable (part # VW3-A66312).• For mounting in an enclosure door, use kit #VW3-A66101 (3-meter cable) orVW3-A66100 (2-meter cable).Switch for access locking to prohibit orauthorize changes to the configuration.Figure 30: Rear View of Keypad DisplayFigure 31: Removing KeypadNOTE: Keypad supplied with this drivecontroller has been matched with thesoftware revision level. Do not installkeypad on another drive controller.Installation of an incompatible keypad mayresult in non-recognition of the keypad bythe drive controller at power-up.Figure 32: Access to RUN and STOP Keys52 © 1996 Square D All Rights Reservedηττπ://νιχοντρολσ.χοm
Page 1 and 2:
Instruction Bulletin50006-519-01BDe
Page 3 and 4:
DANGERHAZARDOUS VOLTAGE• Read and
Page 5:
ALTIVAR 56 Fan and Pump Drive User
Page 8 and 9:
Bulletin No. 50006-519-01BDecember
Page 10 and 11: Bulletin No. 50006-519-01BDecember
Page 28 and 29: AI2-UAI2-IAI2-UAI2-IAI2-UAI2-IAI2-U
Page 52 and 53: AI2-UAI2-IAI2-UAI2-IBulletin No. 50
Page 68 and 69: Bulletin No. 50006-519-01BChapter 5
Page 110 and 111:
Bulletin No. 50006-519-01BChapter 5
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
AUTOOFFHAND234510671098AFCOFFBYPASS
Page 136 and 137:
HANDOFFAUTO241350678OPENMAINSCLOSEF
Page 138 and 139:
Page 140 and 141:
L1 L2 L3TelemecaniqueT1 T2 T3L1 L2
Page 142 and 143:
53 NO 61 NC 71 NO 83 NCTelemecaniqu
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Bulletin No. 50006-519-01BAppendix
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Telemecanique Altivar 56 manual - Northern Industrial

Create successful ePaper yourself

Delete template?

Save as template?