Telemecanique Altivar 56 manual - Northern Industrial

More documents

Recommendations

Info

Bulletin No. 50006-519-01BDecember 1996Chapter 5 — ConfigurationDisplay ModeDISPLAY MODEDrive Controller RunningSPEED REFER.47.2 HzRUNStatus codeWhen the drive controller is running, the Display screen can show one bar graph,two bar graphs, or fourteen items in four tables. Factory setting is one bar graphdisplaying reference frequency. Drive controller status is also displayed in thelower right corner of the screen. Status codes are defined in Table 20. The type andnumber of functions shown can be modified in the 4→Display Configuration menu(page 62) when access level is set to Total Unlock.Drive Controller in FaultStateDISPLAY MODEFAULTAC LINE OVERVOLTAGEFLTStatus codeWhen a fault appears, the drive controller trips, the motor follows theprogrammed fault stop (page 100), and the Display screen shows the fault type.Table 21 lists the faults that the drive controller can display.Table 20: Display Mode Status CodesCode Definition Code DefinitionNLPNo Line Power (control power suppliedseparately)CLI Current LimitRDY Drive Ready DCB DC Injection BrakingRUN Drive Running (at speed) NRP No Run Permissive (LI1 open)Forward Direction BRK BrakingACC AcceleratingDEC DeceleratingFLT FaultFault DesignationIN-PHASE LOSSUNDERVOLTAGEAC-LIN.OVERVOL.DRIVE OVERTEMP.MOT. OVERLOADLOSS FOLLOWEROUT. PHASE LOSSDC-BUS OVERVOL.Table 21: Faults Displayed on Display Mode ScreenDescriptionInput Phase Loss: loss of power or blown fuses. A brief loss of input supplyphase (≤ 200 ms) is not detectedUndervoltage:input voltage ≤ 380 V (60 Hz, 460 V) ATV56•••N4 orinput voltage ≤ 170 V ATV56•••M2 ortemporary voltage loss (t ≥ 200 ms)AC line overvoltage: input voltage to power supply too highinput voltage ≥ 550 V (60 Hz, 460 V) ATV56•••N4 orinput voltage ≥ 270 V ATV56•••M2Drive overtemperature: heatsink temperature too highMotor overload: thermal trip because of prolonged overload or running in singlephase on the output, or motor power rating too low for applicationLoss of follower: loss of the 4-20 mA or 20-4 mA reference at AI2 inputLoss of an output phaseDC bus overvoltage/overcurrent due to excessive braking or overhauling load© 1996 Square D All Rights Reserved55ηττπ://νιχοντρολσ.χοm
Chapter 5 — ConfigurationBulletin No. 50006-519-01BAccess Levels December 1996Table 21: Faults Displayed on Display Mode Screen (Continued)Fault DesignationSHORT CIRCUIT orSHORT CIRCUIT.GROUND FAULTPRECHARGE FAILINTERNAL FAULTMEMORY FAILUREAUTO-TEST FAILOVERSPEEDSEQUENCE T. OUTDescriptionShort circuit or grounding on drive controller output; may be internal or externalGround fault: short circuit to earth on the output of the drive controllerPrecharge failure: capacitor precharge relay faultInternal fault or missing connections on CL1 and CL2Error in storing to EEPROMMain control board failureWithout a tachometer, fault occurs when output frequency is 20% aboveMaximum Frequency parameter setting for 250 mS.Sequence time-out: sequence input not received after Run command withinprogrammed time. Used with Bypass function. See page 85.Process time-out: process input not received after Run command withinPROCESS TIME OUTprogrammed time. Used with Bypass function. See page 85.DYNAMIC BRAKE Dynamic brake resistor lost or connection open. See page 108.TRANS. SHORT C. orShort circuit in transistorGFOPEN TRANSISTOR Transistor has failed openCONTROL SUPPLY CL1/CL2 not connected. Only recognized upon power-up.--No Fault--No fault recordedACCESS LEVELSTotal LockThe keypad display can be locked to limit access to drive controller configurationand adjustment parameters. Two access levels are available: Total Lock (factorydefault) and Total Unlock.Access levels are selected by positioning the access locking switch on back of thekeypad display (Figure 30 on page 52).When the access locking switch is in locked position, the keypad display is in TotalLock mode. Total Lock is the factory preset condition of the drive controller.In Total Lock mode, the choices available from the Main menu are 2→ I/O Map and3→ Fault History. If Keypad Command is active (page 64), the keypad display canbe used for local command of the drive controller; however, all drive controlleradjustment and configuration parameters are protected from change.▲▼MAIN MENUI/O MAPFAULT HISTORYFigure 34: Main Menu in Total Lock ModeTo change access level when in Total Lock mode:1. If Keypad Command is active, from any point in the Level 1 & 2 Software stopthe drive controller, disconnect the keypad display, and set the access lockingswitch to unlock. If Terminal Command is active, it is not necessary to stop thedrive controller before disconnecting the keypad display.2. Reconnect the keypad display.3. Press ENT and display will return to the Drive Configuration menu. Thedrive controller is now in Total Unlock mode. Press ENT to advance throughthe power-up screens to the Main menu.Total UnlockWhen the access locking switch is in the unlocked position, all drive controlleradjustments and configurations are accessible from the Main menu.56 © 1996 Square D All Rights Reservedηττπ://νιχοντρολσ.χοm
Page 1 and 2:
Instruction Bulletin50006-519-01BDe
Page 3 and 4:
DANGERHAZARDOUS VOLTAGE• Read and
Page 5:
ALTIVAR 56 Fan and Pump Drive User
Page 8 and 9:
Bulletin No. 50006-519-01BDecember
Page 10 and 11:
Page 12 and 13:
Page 14 and 15: Bulletin No. 50006-519-01BDecember
Page 28 and 29: AI2-UAI2-IAI2-UAI2-IAI2-UAI2-IAI2-U
Page 52 and 53: AI2-UAI2-IAI2-UAI2-IBulletin No. 50
Page 68 and 69: Bulletin No. 50006-519-01BChapter 5
Page 114 and 115:
Bulletin No. 50006-519-01BChapter 5
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
AUTOOFFHAND234510671098AFCOFFBYPASS
Page 136 and 137:
HANDOFFAUTO241350678OPENMAINSCLOSEF
Page 138 and 139:
Page 140 and 141:
L1 L2 L3TelemecaniqueT1 T2 T3L1 L2
Page 142 and 143:
53 NO 61 NC 71 NO 83 NCTelemecaniqu
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Bulletin No. 50006-519-01BAppendix
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Telemecanique Altivar 56 manual - Northern Industrial

Create successful ePaper yourself

Delete template?

Save as template?