eWON General Reference Guide - eWON wiki

More documents

Recommendations

Info

Note: The Modifier can by omitted, the modifier in bold will be used. General Reference Guide IO Servers Configuration (*) Important: To avoid loss of precision due to Integer to float conversion, choose the right storage DataType for your Tag. See "DataType of Tags" on page 75 Examples • Status register: L CPU Link Bit Hxxxxxx H stands for hexadecimal x: 1 to 6 digits hexadecimal indicating bit offset WL CPU Link Word W, S Hxxxxxx H stands for hexadecimal x: 1 to 6 digits hexadecimal indicating word offset DL CPU Link Double D, L, F Hxxxxxx H stands for hexadecimal x: 1 to 6 digits hexadecimal indicating word offset The STATUS Tag is a special Tag that returns information about the current state of communication for a given device. As for the other Tags, the status Tag ValueName is composed of: Status, Global Device Address • You can define a status Tag for each PLC used. • If you use the status address, the Tag must be configured as analog. 0 Symbol Modifier value range Automatic Tag type W Word 0 .. 65535 DWord S signed Word -32768 .. 32767 Integer D DWord 0 .. 4294967296 (*) DWord L signed DWord -2147483648 .. 2147483647 (*) Integer F Float +/- 3.4e38 Float Table 129: HITACHI Modifiers address point to XH00103 selection of bit3 of word 0 of the input device located at remote:0 unit:0 slot:1 WYH0011 selection of word 0 of the output device located at at remote:0 unit:0 slot 1 RH105 bit 105 hex (261 decimal) of the Internal Output Bit Dedicated area WRSH10 short located at word 10 hex of the WR area WMH10 word 10 hex of the Internal Word Output Common area DMH10 double word 10 + 11 hex of the Internal Word Output Common area WMH000010 word 10 hex of the Internal Word Output Common area (WMH10 is more optimal) Table 130: HITACHI register address examples Communication not initialized. Status UNKNOWN. If no Tag is polled on that device address, the communication status is unknown. 1 Communication OK. 2 Communication NOT OK. Table 128: HITACHI Memory types and address scheme Table 131: Tag Status meaning RG-001-0-EN ver 1.14 eWON® - 02/05/2012 - ©eWON sa Page 151
General Reference Guide IO Servers Configuration 5.14.2.2 Global Device Address The device address is either appended to the ValueName in the Item Name definition, or entered in the Topic global address fields. The device address syntax is the following: EH[,[[ipaddress,TCP|UDP,port]|[station]][,LUMP]] EH,station EH EH,station,LUMP EH,LUMP EH,ipaddress,TCP|UDP,port EH,ipaddress,TCP|UDP,port,LUMP EH Serial station : address of the PLC on the network EH,4 the eWON will access PLC number 4. By configuration, an HITACHI PLC could have an undefined station number. If this PLC is alone on a serial link, you don’t need to specify a station number. station : address of the PLC on the network LUMP : Link Unit Port Module EH,4,FFFF0000 the eWON will access PLC number 4 with the LUMP FFFF0000. By configuration, an HITACHI PLC could have an undefined station number. If this PLC is alone on a serial link, you don’t need to specify a station number. LUMP : Link Unit Port Module EH,FFFF0000 the eWON will access PLC with the LUMP FFFF0000. EH ethernet ipaddress : IP address of the PLC TCP|UDP : select the protocol used port : IP port used EH,10.0.120.203,TCP,3004 the eWON will access the PLC at 10.0.120.203 with protocol TCP and port 3004 ipaddress : IP address of the PLC TCP|UDP : select the protocol used port : IP port used LUMP : Link Unit Port Module EH,10.0.120.203,TCP,3004,FFFF0000 the eWON will access the PLC at 10.0.120.203, protocol TCP, port 3004 and LUMP FFFF0000 Table 132: HITACHI device address syntax Important: If the PLC address is defined at the Topic level, it can be omitted in the Tag definition. In that case the Tag name will only contain the "ValueName". If the PLC address is specified at the Topic level, it will replace any address defined Tag by Tag. RG-001-0-EN ver 1.14 eWON® - 02/05/2012 - ©eWON sa Page 152
Page 1 and 2:
eWON Family 500, 2001, 2001CD, 4001
Page 3 and 4:
Table of content 5.4.3 Tag name con
Page 5 and 6:
Table of content 8.3.3 $dtRL [Real
Page 7 and 8:
2 The eWON login page 2.1 Access fr
Page 9 and 10:
3.2 Users Setup The Users Setup pag
Page 11 and 12:
3.2.5 User’s directory restrictio
Page 13 and 14:
3.3 System Setup General Reference
Page 15 and 16:
3.3.1.2 Alarms (globals parameters)
Page 17 and 18:
3.3.1.5 Task Planner Since Firmware
Page 19 and 20:
3.3.1.5.2 Edit Action page When you
Page 21 and 22:
General Reference Guide eWON Config
Page 23 and 24:
When using modem port for VCOM, the
Page 25 and 26:
3.3.2.7 SNMP Setup 3.3.2.7.1 Commun
Page 27 and 28:
3.3.3 Diagnosis 3.3.3.1 Overview Ge
Page 29 and 30:
3.3.3.4 Debug Control Description L
Page 31 and 32:
3.3.4.1.1 Modem setup page Warning:
Page 33 and 34:
Page 35 and 36:
3.3.4.1.1.4 PSTN: Leased line confi
Page 37 and 38:
3.3.4.1.2 Ethernet LAN & WAN From t
Page 39 and 40:
Each mechanisms provides you all or
Page 41 and 42:
Page 43 and 44:
Select next server in case of error
Page 45 and 46:
3.3.4.2.3 ADSL General Reference Gu
Page 47 and 48:
Page 49 and 50:
VPN between two eWONs General Refer
Page 51 and 52:
VPN with an ENDIAN Server You can f
Page 53 and 54:
Ethernet WAN Connection - Disconnec
Page 55 and 56:
3.3.4.3 Networking Config 3.3.4.3.1
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
3.3.4.3.6 Proxy 3.3.4.3.6.1 Why a p
Page 65 and 66:
3.3.4.3.7 Security You can define t
Page 67 and 68:
Page 69 and 70:
3.3.4.5 STORAGE General Reference G
Page 71 and 72:
3.3.4.5.2 Erase & Format Figure 62:
Page 73 and 74:
3.3.4.5.3.2 Edit parameters General
Page 75 and 76:
Page 77 and 78:
3.4.1.2 Tags validation General Ref
Page 79 and 80:
3.4.2.1 Tag main edit window Genera
Page 81 and 82:
Control Description Tag name Tag De
Page 83 and 84:
Page 85 and 86:
3.4.2.2.1 Email on alarm configurat
Page 87 and 88:
Examples: General Reference Guide e
Page 89 and 90:
3.5 Pages configuration Page defini
Page 91 and 92:
Page 93 and 94:
3.8 Wizards To help you quickly and
Page 95 and 96:
5 The eWON IO Servers 5.1 Introduct
Page 97 and 98:
5.2.4 Standard IO server configurat
Page 99 and 100:
General Reference Guide IO Servers
Page 101 and 102: 5.3.3 Tag name convention IO Server
Page 103 and 104: 5.3.3.2 Slave Address This is the a
Page 105 and 106: 5.4.3.1 ValueName General Reference
Page 107 and 108: General Reference Guide IO Servers
Page 109 and 110: • Status register: General Refere
Page 111 and 112: eWON DF1 address 5.6.2.2 Topic conf
Page 113 and 114: 5.6.3 Tag name convention IO Server
Page 115 and 116: • "e" indicates the element numbe
Page 117 and 118: Serial FINS network Serial FINS nod
Page 119 and 120: Supported memory areas: Modifier: G
Page 121 and 122: 5.8 S5-AS511 IO Server 5.8.1 Introd
Page 123 and 124: NOTES: • For DB the smallest elem
Page 125 and 126: 5.9.2.1 Communication Setup General
Page 127 and 128: 5.9.3.1 ValueName ValueName follows
Page 129 and 130: Example of use of SN_LO and SN_HI i
Page 131 and 132: 5.10.2.2.1 ENERGY TAGS The followin
Page 133 and 134: 5.10.2.3.2 PT100 input AI5 and AI6
Page 135 and 136: 5.11 MEM IO Server 5.11.1 Introduct
Page 137 and 138: Baud Rate General Reference Guide I
Page 139 and 140: 5.12.2.3 Topic configuration Genera
Page 141 and 142: DB1B13#3 represents bit 3 of Byte 1
Page 143 and 144: 5.13 S7-200 (PPI - ISOTCP) 5.13.1 I
Page 145 and 146: 5.13.2.3 COM configuration (MPI por
Page 147 and 148: 5.13.3.1 Value Name The syntax is t
Page 149 and 150: 5.14 HITACHI IO Server 5.14.1 Intro
Page 151: 5.14.2.1 Value Name The syntax is t
Page 155 and 156: 5.15.2.2 Topic configuration Genera
Page 157 and 158: General Reference Guide IO Servers
Page 159 and 160: 5.16.3 Tag name convention General
Page 161 and 162: 5.17 MITSUBISHI MELSEC IO Server 5.
Page 163 and 164: Note: The Modifier can be omitted,
Page 165 and 166: 6.1 Real-time screen General Refere
Page 167 and 168: General Reference Guide Monitoring
Page 169 and 170: 6.4 Real time Alarm screen Figure 1
Page 171 and 172: 6.6 Files transfer This link gives
Page 173 and 174: General Reference Guide Monitoring
Page 175 and 176: 6.7.2.1 Memory Information 6.7.2.2
Page 177 and 178: 6.7.2.5 Info 6.7.3 Scheduled Action
Page 179 and 180: 6.7.4.2 Activate Energy debug mode
Page 181 and 182: 6.7.5 ADSL Log General Reference Gu
Page 183 and 184: General Reference Guide Retrieving
Page 185 and 186: 8 Export Block Descriptor Exports a
Page 187 and 188: 8.2.3 $st [Start Time] and $et [End
Page 189 and 190: 8.3 Data Types description and synt
Page 191 and 192: 8.3.2 $dtHT [Historical Table] Gene
Page 193 and 194: 8.3.3 $dtRL [Real time Logging] Gen
Page 195 and 196: 8.3.5 $dtAR [Alarm Real time] 8.3.5
Page 197 and 198: 8.3.7 $dtSS [Scheduled Status] Gene
Page 199 and 200: 8.3.9 $dtUF [User File] 8.3.9.1 Exp
Page 201 and 202: 8.3.10 $dtIV [Instant Values] Gener
Page 203 and 204:
General Reference Guide Export Bloc
Page 205 and 206:
8.3.12 $dtPP General Reference Guid
Page 207 and 208:
8.3.15 $dtRE [Real Time Diagnostic]
Page 209 and 210:
8.3.16.5 Examples $dtTR $fnmytar.ta
Page 211 and 212:
The new firmware is uploaded to the
Page 213 and 214:
9.3 Upgrading the eWON firmware by
Page 215 and 216:
9.4 Downgrade firmware 9.4.1 Firmwa
Page 217 and 218:
10 Appendix 10.1 Access to the eWON
Page 219 and 220:
10.5 Resetting the eWON 10.5.1 Over
Page 221 and 222:
10.6 Table of comparisons between e
Page 223 and 224:
10.9 GSM modem Led behavior Figure
show all

eWON General Reference Guide - eWON wiki

Create successful ePaper yourself

Delete template?

Save as template?