Facskó Ferenc (szerk.) (2012): Kutatások a Nyugat-magyarországi
Facskó Ferenc (szerk.) (2012): Kutatások a Nyugat-magyarországi
Facskó Ferenc (szerk.) (2012): Kutatások a Nyugat-magyarországi
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
A regionális fejlődés műszaki innovációs hátterének fejlesztése<br />
8 - 16 mm-es csapméretnél 0,00 és 0,035 mm határok között lehet, optimálisan 0,1<br />
mm. Ennek betartása a csap illetve csaprés tűrésére az illesztés pontosságának<br />
megfelelő folyamatképessége érdekében ±0,09 ~ 0,10 mm-t kellene előírni, ami az<br />
alkatrész-megmunkálási folyamatok szigorú szabályozásával is nehezen biztosítható.<br />
Alternatív megoldásként az alkatrésztűrés, a közepes átfedés és a megengedhető<br />
maximális átfedés illetve hézag kompromisszumát lehet keresni. Megállapításaink<br />
szerint a kompromisszum érték ± 0,10 és ± 0,20 mm között lehet. A kérdés<br />
külön megvizsgálandó kemény lombosok és más mérettartományok esetén.<br />
Kutatási eredményeink hasznosulása folyamatban van. Hasznosítási területek: bútoripari<br />
és fa ablak- ajtógyártó vállalkozások.<br />
Publikációk:<br />
PAPP, T. – KOVÁCS, ZS. (<strong>2012</strong>): Development of process capability based fi ts and tolerances<br />
for the enhancement of productibility in the secondary wood processing. International<br />
Scientifi c Conference on Sustainable Development and Ecological Footprint. March<br />
27-27. Sopron, Hungary.<br />
Abstract – Performance of assemblies of solid wood parts is determined by tightness of fi t<br />
between them. Producing acceptable fi t depends on the precision of machining the parts.<br />
Process capability for typical machines of secondary woodworking has been determined and<br />
analyzed with consideration to wood moisture changes. The authors studied the functionally<br />
allowable limits of fi t tightness and the derived tolerances for work pieces. Possibilities<br />
for improving process capabilities when needed and for fi nding compromise between functional<br />
and processes requirements have been investigated.<br />
PAPP, T. – KOVACS, ZS. (2011): Determination of reasonable fi t interferences for solid wood<br />
joints using fi nite elemet method (FEM). 2 ND INTERNATIONAL JOINT CONFER-<br />
ENCE ON ENVIRONMENTAL AND LIGHT INDUSTRY TECHNOLOGIES; November<br />
21-22; Budapest<br />
Abstract – Performance of joints of solid wood parts such as diff erent types of mortise and<br />
tenon joints depends much on the tightness of fi t between tenon and mortise. Generally interference<br />
between tenon and mortise thickness is needed for a good load bearing capacity<br />
of the joint, the extent of which depends on wood species. A limiting factor for fi t tightness<br />
is the development of tensile stresses across grain direction around the corners. These<br />
stresses can be modelled by fi nite element technique using orthotropical material models.<br />
The objective of this paper is to defi ne reasonably applicable interferences in the case of<br />
joints of diff erent wood species on the basis of across-the-grain tensile stresses introduced<br />
in the solid wood parts when assembling joints. Finite element models elaborated for the<br />
joints studied are verifi ed by physical testing. Tests extend to assessing the performance of<br />
the joints.<br />
PAPP, T. – KOVACS, ZS. (2010): Enhancement of the machining of solid wood parts for upholstered<br />
furniture. INTERNATIONAL JOINT CONFERENCE ON ENVIRONMEN-<br />
TAL AND LIGHT INDUSTRY TECHNOLOGIES; november 18-19; Budapest<br />
Abstract – The primary objective of our study was to determine to what extent the productivity<br />
of profi le machining of the solid wood furniture parts can be increased without<br />
compromising the precision of machining. The method of investigation was studying the<br />
269