Download Adept Cobra i600 User's Guide - pulsar.com.tr

More documents

Recommendations

Info

Chapter 5 - System Operation 72 <strong>Adept</strong> <strong>Cobra</strong> <strong>i600</strong>/i800 Robot User’s <strong>Guide</strong>, Rev B
Optional Equipment Installation 6 6.1 Installing End-Effectors The user is responsible for providing and installing any end-effector or other end-of-arm tooling. End-effectors can be attached to the user flange using four M6 screws. See Figure 9-4 on page 114 for a detailed dimension drawing of the user flange. A 6 mm diameter x 12 mm dowel pin (not supplied) fits in the through hole in the user flange and can be used as a keying or antirotation device in a user-designed end-effector. If hazardous voltages are present at the end-effector, you must install a ground connection from the base of the robot or the outer link to the end-effector. See “Robot-Mounted Equipment Grounding” on page 48. NOTE: A threaded hole is provided on the user flange (see Figure 9-4 on page 114). The user may attach a ground wire through the quill connecting the outer link and the user flange. 6.2 Removing and Installing the User Flange The user flange can be removed and reinstalled if this is required for a specific reason. If the flange is removed, it must be reinstalled in exactly the same position to avoid losing the calibration for the system. There is a setscrew on the flange that holds the rotational position of the flange on the quill shaft. A ball bearing behind the setscrew contacts the shaft in one of the vertical-spline grooves in the shaft. Follow the procedures below to remove and replace the flange assembly. Removing the Flange 1. Turn off High Power and system power to the robot. 2. Remove any attached end-effectors or other tooling from the flange. 3. Use a 2.5 mm Allen driver to loosen the setscrew (see Figure 6-1 on page 74). Note the vertical-spline groove that is in line with the setscrew. You must replace the flange in the same position. 4. Use a Torx 25 driver to loosen the two M4 Torx-head screws. 5. Slide the flange down slowly until it is off the shaft. Be careful not to lose the ball bearing (3.5 mm) that is inside the flange behind the setscrew. <strong>Adept</strong> <strong>Cobra</strong> <strong>i600</strong>/i800 Robot User’s <strong>Guide</strong>, Rev B 73
Page 1:
Adept Cobr
Page 4 and 5:
The information contained herein is
Page 6 and 7:
Table of Contents Before Unpacking
Page 8 and 9:
Table of Contents 6.5 Installing Ro
Page 10 and 11:
Table of Contents 10 Adept<
Page 12 and 13:
List of Figures Figure 6-7. Joint 1
Page 14 and 15:
Chapter 1 - Introduction Joint 2 Jo
Page 16 and 17:
Chapter 1 - Introduction 1.3 How Ca
Page 18 and 19:
Chapter 2 - Safety 2.2 Warning Labe
Page 20 and 21:
Chapter 2 - Safety 2.3 Precautions
Page 22 and 23: Chapter 2 - Safety 2.4 Intended Use
Page 24 and 25: Chapter 2 - Safety 2.6 Transport Al
Page 26 and 27: Chapter 2 - Safety All personnel mu
Page 28 and 29: Chapter 2 - Safety 28 Adept
Page 30 and 31: Chapter 3 - Robot Installation 3.2
Page 36 and 37: Chapter 4 - System Installation 4.2
Page 42 and 43: Chapter 4 - System Installation <st
Page 44 and 45: Chapter 4 - System Installation sha
Page 46 and 47: Chapter 4 - System Installation Rem
Page 48 and 49: Chapter 4 - System Installation Rob
Page 50 and 51: Chapter 5 - System Operation 5.2 Di
Page 52 and 53: Chapter 5 - System Operation 5.4 Fr
Page 54 and 55: Chapter 5 - System Operation Option
Page 56 and 57: Chapter 5 - System Operation XIO Ou
Page 58 and 59: Chapter 5 - System Operation Table
Page 60 and 61: Chapter 5 - System Operation Table
Page 62 and 63: Chapter 5 - System Operation <stron
Page 64 and 65: Chapter 5 - System Operation Muted
Page 66 and 67: Chapter 5 - System Operation 5.7 Tu
Page 68 and 69: R Chapter 5 - System Operation Opti
Page 70 and 71: R Chapter 5 - System Operation Opti
Page 74 and 75: Chapter 6 - Optional Equipment Inst
Page 88 and 89: Chapter 7 - Using the Manual Contro
Page 102 and 103: Chapter 8 - Maintenance 8.2 Checkin
Page 104 and 105: Chapter 8 - Maintenance Joint 3 Bal
Page 106 and 107: Chapter 8 - Maintenance Figure 8-3.
Page 108 and 109: Chapter 8 - Maintenance Groove in r
Page 110 and 111: Chapter 8 - Maintenance 8. The batt
Page 112 and 113: Chapter 9 - Technical Specification
Page 122 and 123:
Index installation 73 environmental
Page 124 and 125:
Index W warning labels, location 18
Page 128:
P/N: 03589-000, Rev B 3011 Triad Dr
show all

Download Adept Cobra i600 User's Guide - pulsar.com.tr

Create successful ePaper yourself

Delete template?

Save as template?