Version 5.3.02 - Serendipity Software

More documents

Recommendations

Info

Loupe The Loupe mode positions a loupe on the SoftProof window. The Touch Console action pane acts like a drawing tablet. Touch and drag your finger on the touch screen to move the loupe over your image. Buttons around the edges of the console control the Loupe’s features: • Smaller / Bigger – Decrease or increase the size of the loupe. • Zoom In / Out – Increase or decrease the magnification of the loupe. • Solo Previous / Next Channel – These controls allow individual Ink Channels of the job to be viewed within the Loupe, acting as the Show Channels function. The buttons cycle through each individual channel then show all channels (default view). • Toggle HUD – Toggles the Heads Up Display in the Loupe window, showing the CMYK dot percentages at the centered cross-‐hair or within the average % box. • Screened Pixel Readout – Toggles the HUD between cross-‐hair point measurement of ink percentages and a square for measuring area average dot percentages. The square resizes depending on the zoom % to always cover an area equal to a full halftone cell at the LPI defined in SoftProof Settings. Calibrate The Calibration control screen allows operators to initiate Monitor Calibration and Calchecks for the main SoftProof display. • Calibrate – Opens the Displays application and begins the calibration process for the main SoftProof display. Once calibrated, the monitor ICC profile is automatically saved as the operating system default, replacing the previous ICC profile. Note: When calibrating or calchecking, the Spectrophotometer assigned in the Displays application for either task should be connected and ready for use. If the instrument is different to the assigned one an error will occur, ceasing the operation. It is recommended to check the appropriate Spectrophotometers have been assigned before using the Calibrate or Calcheck functions (see Applications > Displays). • Calcheck – This option will open the Displays application, starting a Calcheck of the softproof display to the standard patch set in the chart assigned to the current Press. On completion, the Calcheck status of the monitor is updated with a tick/cross. This button is only available if the currently selected Press Config has an assigned Calcheck Chart. Note on Spot Colours: When performing a calcheck of the softproofing display, any special/spot colours included in the currently loaded job are measured and included in the Calcheck for the purposes of a pass or fail. View FlipBook View FlipBook displays a list of available publications that may be opened and viewed using the FlipBook application. Once a publication is opened, FlipBook controls will appear on the console: • View 3D, View Calendar, Show Borders and Rendered Thumbnails toggles. • Decrement/Increment Start Page, Even/Odd Top Page, Read Direction 1-‐>2 / 2
• Book Order – Select which BookFilter queues are made available for view/proofing in the Books list. • TouchConsole Settings – See below for more information. Touch Console Settings Default job viewing and touch screen navigation options can be configured using the Touch Console Settings. There are two tabs – TouchConsole and SoftProof: Touch Console • ScrollBar – Enable or disable the scrollbar and set the default side it appears on (Right or Left). • Thumbnails – Enable or disable viewing thumbnails for Publications, Jobs or All selection lists. • View – Enable or disable View Imaged (default), View Rendered and/or View Flipbook options for opening jobs or publications for softproofing. Note: If only one of the View Images or View Rendered is selected, the Touch Console button will simply be labelled “View”. If all options are disabled, View Imaged will be selected as the default option. • Button Size – Set the size of the Touch Console buttons in mm/inches. Note: The Touch Console application must be closed and restarted for settings to take effect. SoftProof • Entry Screen on Load – Select the control screen the Touch Console will default to when loading a new job/page: o Main – The console defaults to the Main screen on load. o Navigate – The console defaults to the Navigate o screen on load. Pages – The console defaults to the Show Pages screen on load. • Navigate Option – Choose whether the Navigate console screen has the Previous Page/Next Page or Zoom In/Zoom Out buttons. • Duplicate Page Settings (Veripress/Blackmagic Softproofing Add-‐On Only) – When viewing a publication with duplicate (purple) pages, choose from these page load options: o Manual Select – When a page with duplicates is selected in the Show Pages screen, the page to view must be manually selected. This is the default mode of a non-‐Veripress Touch Console. o Select Newest Page – Useful in publishing workflows where page updates/revisions are common. This option will automatically display the latest version of the page. • Publication Load Page (Veripress/Blackmagic Softproofing Add-‐On Only) – Set the page to be viewed on load when viewing a publication from the following options: o Manual Select – When a publication is selected for softproofing the Touch Console opens and the Show Pages screen allows the user to select the page to be viewed first. o First Available Page – Publications are loaded on the first available (lowest numbered) page. • Edit Touch Console UI – Opens an Edit Interface window to allow for the configuration of the enabled (visible) buttons for control of SoftProof in the Main screen of the Touch Console. Enable or disable buttons by selecting them. Those disabled will appear with a red cross and will be excluded from the Touch Console when using it to view softproofs. The Toolbar has a Preview checkbox to see how the Touch Console controls will appear and a Reset button to restore and enable all buttons. Serendipity Software -‐ Veripress User Manual – Version 5.3.02 101
Page 1 and 2:
User Manual Version 5.3.02
Page 3 and 4:
Media..............................
Page 5 and 6:
Veripress User Manual Copyright
Page 7 and 8:
Installation The installation se
Page 9 and 10:
Mac OS X Installation Administr
Page 11 and 12:
Upgrading to Version 5.3 This
Page 13 and 14:
Mac OS X - Upgrading to Versi
Page 15 and 16:
Saving/Restoring the Veripress D
Page 17 and 18:
Starting the Client Once the S
Page 19 and 20:
RIP Configuration If your Verip
Page 21 and 22:
The Veripress Server The Veripr
Page 23 and 24:
The Veripress Dongle Updater Th
Page 25 and 26:
Menu Options Application • Acc
Page 27 and 28:
Workbench Data Types There are
Page 29 and 30:
Calcheck Chart The Calcheck Cha
Page 31 and 32:
Camera The Camera data type is
Page 33 and 34:
Job Genie Plate separated, sing
Page 35 and 36:
Note: The To Separator and Tru
Page 37 and 38:
Tabs - (5) Display The Display
Page 39 and 40:
ICC Profiles ICC Profiles are
Page 41 and 42:
Collating Collating is a method
Page 43 and 44:
When adding a new printer thro
Page 45 and 46:
Input Screening Input Screening
Page 47 and 48:
Media Effects The attributes he
Page 49 and 50: Regular Expression The Regular
Page 51 and 52: Tab 2 - Exact When using the
Page 53 and 54: File Transfer Priority This spe
Page 55 and 56: o o o o Group Pages - Group the
Page 57 and 58: Special Colour Set Veripress us
Page 59 and 60: Note: The 3 swatch charts are
Page 61 and 62: BookMonitor The BookMonitor modu
Page 63 and 64: ClusterStatus The ClusterStatus
Page 65 and 66: QueueManager The QueueManager di
Page 67 and 68: Version 3.0 Rotations Surface
Page 69 and 70: RIPMonitor The RIPMonitor displa
Page 71 and 72: Status Status shows the current
Page 73 and 74: Archives The Archives Applicatio
Page 75 and 76: • Render - Shows the number
Page 77 and 78: • Name - Save the name of t
Page 79 and 80: o Custom - Type in the field
Page 81 and 82: Clicking on a Display name und
Page 83 and 84: Page View (Contextual Menu) The
Page 85 and 86: Jobs The Jobs application is u
Page 87 and 88: Press Agent The Press Agent ap
Page 89 and 90: Click on the Tick/Cross to pop
Page 91 and 92: • Show Excess Ink Weight Area
Page 93 and 94: • Rotation - Control the orie
Page 95 and 96: The page boxes are colour code
Page 97 and 98: Touch Console The Touch Console
Page 99: • Auto Crop - Remove white s
Page 103 and 104: • Nest - Submits the jobs fo
Page 105 and 106: Accounts Admin / Secure Mode V
Page 107 and 108: Hosts Panel The Hosts panel al
Page 109 and 110: Additional Monitors Specific set
Page 111 and 112: • Spool - The location where
Page 113 and 114: Log File - To view the log f
Page 115 and 116: 8. Print Using - Select Printer
Page 117 and 118: • Click Next. • Additional P
Page 119 and 120: Troubleshooting Clustering Here
Page 121 and 122: Copyright Notices PNG Library C
Page 123 and 124: Code in sys/linux is developed
Page 125 and 126: If distribution of executable o
Page 127 and 128: Copyright The XFree86 Project,
Page 129 and 130: Importing Signatures Dynastrip...
show all

Version 5.3.02 - Serendipity Software

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?