HP ProBook 4540s Notebook PC Reference Guide - static ...

More documents

Recommendations

Info

Adding new locations when traveling On a new computer, the only location setting available to the modem is a location setting for the country or region in which you purchased the computer. As you travel to different countries or regions, set the internal modem to a location setting that meets the operating standards of the country or region in which you are using the modem. As you add new location settings, they are saved by the computer so that you can switch among settings at any time. You can add multiple location settings for any country or region. CAUTION: To reduce the risk of losing your home country or region settings, do not delete your current modem country or region settings. To enable modem use in other countries or regions while preserving your home country or region configuration, add a new configuration for each location in which you will use the modem. CAUTION: To reduce the risk of configuring the modem in a way that violates the telecommunications regulations and laws of the country or region you are visiting, select the country or region in which the computer is located. The modem may not function properly if the correct country or region selection is not made. 1. Select Start > Devices and Printers. 2. Right-click the device that represents your computer, and click Modem settings. NOTE: You must set up an initial (current) location area code before you can view the Dialing Rules tab. If you do not have a location already set up, you are prompted to enter the location when you click Modem settings. 3. Click the Dialing Rules tab. 4. Click New. The New Location window opens. 5. In the Location name box, type a name (such as home or work) for the new location setting. 6. Select a country or region from the Country/region list. (If you select a country or region that is not supported by the modem, the country/region selection for USA or UK is displayed.) 7. Enter the area code, a carrier code (if necessary), and the number for an outside line (if necessary). 8. Next to Dial using, click Tone or Pulse. 9. Click OK to save your new location setting. 10. Do one of the following: ● ● To set your new location setting as the current location, click OK. To select another location setting as the current location setting, select your preference from the settings in the Location list, and then click OK. NOTE: You can use the preceding procedure to add location settings for places within your own country or region as well as in other countries or regions. For example, you could add a setting named Work that includes dialing rules for accessing an outside line. 12 Chapter 2 Networking (select models only)
Connecting to a local area network (LAN) (select models only) Connecting to a LAN requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the network cable into a network wall jack (2) or a router (not illustrated). WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem cable or telephone cable into an RJ-45 (network) jack. Connecting to a wired network 13
Page 1 and 2: HP Notebook Reference Guide
Page 3 and 4: Safety warning notice WARNING! To r
Page 5 and 6: Table of contents 1 Introduction ..
Page 7 and 8: Testing an AC adapter .............
Page 9: 9 Computer Setup (BIOS) and Advance
Page 12 and 13: 2 Networking (select models only) Y
Page 14 and 15: Turning wireless devices on or off
Page 16 and 17: Setting up a new WLAN Required equi
Page 18 and 19: Inserting a SIM NOTE: To identify t
Page 20 and 21: Connecting a modem cable 1. Plug th
Page 24 and 25: 3 Multimedia Your computer may incl
Page 26 and 27: The webcam software enables you to
Page 28 and 29: HDMI The HDMI port connects the com
Page 30 and 31: 4 Power management NOTE: A computer
Page 32 and 33: To initiate Hibernation: ▲ Click
Page 34 and 35: Using HP Power Assistant (select mo
Page 36 and 37: NOTE: For additional information ab
Page 38 and 39: When you disconnect external AC pow
Page 40 and 41: for full-screen applications that u
Page 42 and 43: Removing a digital card CAUTION: To
Page 44 and 45: Removing an ExpressCard CAUTION: To
Page 46 and 47: Connecting a USB device CAUTION: de
Page 48 and 49: Connecting an eSATA device CAUTION:
Page 50 and 51: USB drives include the following ty
Page 52 and 53: 6 Drives Handling drives CAUTION: D
Page 54 and 55: Using HP 3D DriveGuard (select mode
Page 56 and 57: 5. Gently press the disc (3) down o
Page 58 and 59: 3. Remove the disc (3) from the tra
Page 60 and 61: 7 Security Protecting the computer
Page 62 and 63: Setting passwords in Windows Passwo
Page 64 and 65: Changing a BIOS administrator passw
Page 66 and 67: Removing Automatic DriveLock protec
Page 68 and 69: Using Internet security software Wh
Page 70 and 71: 8 Maintenance Cleaning your compute
Page 72 and 73:
Updating programs and drivers HP re
Page 74 and 75:
Using HP Software Setup utility HP
Page 76 and 77:
To exit Computer Setup menus, choos
Page 78 and 79:
Using f10 setup to update the BIOS
Page 80 and 81:
Main menu Select To do this System
Page 82 and 83:
10 MultiBoot About the boot device
Page 84 and 85:
● ● ● Changing the boot order
Page 86 and 87:
A Traveling with the computer If yo
Page 88 and 89:
B Troubleshooting resources ● Acc
Page 90 and 91:
Index Symbols/Numerics 1394 cable,
Page 92:
Disk Defragmenter 43 firewall 58 HP
show all

HP ProBook 4540s Notebook PC Reference Guide - static ...

Create successful ePaper yourself

Delete template?

Save as template?