Hughes 9201 BGAN Terminal User's Guide 2.2 - GMPCS Personal ...

More documents

Recommendations

Info

1 2 3 4 5 6 Description of Failure ActionWLAN interfaceG G G BR B B The main processor has detected a fault in theASICG G G BR BG BR The main processor has detected a fault in thetransmitterG G G BR BR BG The secondary processor has detected a fault inits memoryNote 1Note 1Note 1G G G BG BR BR The secondary processor has failed to start Note 1Note 1: Remove all data cables and power cables from the terminal (remember to remove thebattery). Wait 30 seconds, then reconnect power and re-start the terminal. If this does not clearthe failure, follow the troubleshooting procedures below.Note2: Re-load the terminal’s SW using the BGAN LaunchPad.TROUBLE SHOOTING BOOT MODE PROBLEMSIf a SW upgrade fails, the UT will come up in boot mode and the LEDs will be lit up as indicated inthe above chart. A known problem in this mode is that the DHCP server does not work. If thecommunication to the UT can not be established, then you have to manually configure the IPaddress of the connected PC by going to your Network Connection icon and right click andselect “Properties”. The following screen shot shows your Network Connections. You need toselect the connection that is tied to your Ethernet card (e.g. Local Area Connection 4). Rightclick on the LAN connection (maybe named differently) and select “Properties”.The following screen appears. Scroll down until you find the Internet Protocol (TCP/IP) and thenclick on “Properties”.94 Hughes 9201 BGAN Terminal User's Guide 2.2
The following screen appears:Click on the radio button that says “Use the following IP address”The static IP address information below should be entered:IP Address: 192.168.128.101Subnet Mask: 255.255.255.0Default GW: 192.168.128.100Click on OK to confirm the entries..To verify the connection to the terminal, open a DOS command window and at the DOS prompttry pinging the UT by typing “ping 192.168.128.100”. If you get 4 replies back, you know you haveconnectivity to the UT.Once you have connectivity to the UT, then you can use the Hughes Upgrader to load the latestsoftware into the UT. You can download the latest Upgrader and software from the Hugheswebsite by using the following link:http://bgan.hughes.comHughes 9201 BGAN Terminal User's Guide 2.2 95
Page 2:
Copyright © 2007 Hughes Network Sy
Page 5 and 6:
PACEMAKERSThe various brands and mo
Page 7:
Size and Weight ...................
Page 11 and 12:
INTRODUCTIONABOUT THIS PRODUCTThe H
Page 13 and 14:
PACKAGE CONTENTSWhen you unpack the
Page 15 and 16:
GETTING STARTEDINTRODUCTION TO GETT
Page 17 and 18:
PUT THE BATTERY ON CHARGETo charge
Page 19 and 20:
which case the terminal may be able
Page 21 and 22:
CONNECTING BY ETHERNETTo connect th
Page 23 and 24:
CONNECTING WITH THE NETWORKEstablis
Page 25 and 26:
5. After you have positioned the Te
Page 27 and 28:
5. When you have successfully regis
Page 29 and 30:
REGISTRATION STATUS AND COVERAGE MA
Page 31 and 32:
LAUNCHPAD SOFTWARE INSTALLATIONSUPP
Page 33 and 34:
2. Follow the on-screen instruction
Page 35 and 36:
• Installation CompleteHughes 920
Page 37 and 38:
ESTABLISHING COMMUNICATIONS BETWEEN
Page 39 and 40:
INDICATOR LIGHTS (LEDS)The LEDs ind
Page 41 and 42:
These LEDs also indicate the signal
Page 43 and 44:
The Extended lithium ion battery pa
Page 45 and 46:
ISDN COMPATIBLE DEVICESThe terminal
Page 47 and 48:
PERSONALIZATIONAfter the PIN check,
Page 49 and 50:
In the second phase, the Upgrader l
Page 51 and 52:
hexadecimal format. If you have pro
Page 53 and 54: BGAN SERVICESVOICE TELEPHONY SERVIC
Page 55 and 56: SupplementaryServiceDescriptionStri
Page 57 and 58: DATA SERVICESLaunchPad provides a v
Page 59 and 60: OPENING DATA CONNECTIONSData connec
Page 61 and 62: OPENING A DEDICATED STREAMING CONNE
Page 63 and 64: OPENING A VPNTo open a VPN connecti
Page 65 and 66: 9. Click on Apply to save the displ
Page 67 and 68: MANAGING ISDN CONNECTIONSOPENING AN
Page 69 and 70: If a user has a TE device that can
Page 71 and 72: USIM APN MODE VS. MANUAL APN MODETh
Page 73 and 74: Hughes 9201 BGAN Terminal User's Gu
Page 75 and 76: The phonebook is stored on the USIM
Page 77 and 78: From this window you can:• Create
Page 79 and 80: DELETING A CONTACTTo delete a conta
Page 81 and 82: TCP PEP SOFTWARETransmission Contro
Page 83 and 84: 2. Click on OK to restart the termi
Page 85 and 86: CONFIGURING A CONNECTIONThis sectio
Page 87 and 88: 5. Click on Apply to save the displ
Page 89 and 90: CONFIGURING ROUTING OPTIONSTo confi
Page 91 and 92: CONFIGURING SUPPORT DETAILSUsing th
Page 93 and 94: EXPORTING A USER LOGINIf required,
Page 95 and 96: CHANGING THE FACILITY PASSWORDYou c
Page 97 and 98: SOFTWARE VERSIONS AND AVAILABILITYY
Page 99 and 100: To clear a BGAN log file from your
Page 101 and 102: 2. Select the file to email from th
Page 103: POWER-ON SELF-TESTSATELLITE TERMINA
Page 107 and 108: The following functions are also av
Page 109 and 110: Problem Possible Cause Possible Sol
Page 111 and 112: TECHNOLOGY OVERVIEWGPSThe Global Po
Page 113 and 114: WLANWireless Local Area Networking
Page 115 and 116: DECLARATION OF CONFORMITYHughes Net
Page 117 and 118: affect the data transmission rates.
show all

Hughes 9201 BGAN Terminal User's Guide 2.2 - GMPCS Personal ...

Create successful ePaper yourself

Delete template?

Save as template?