Planning with SIVACON 8 PS - Siemens

Planning with BD2A/BD2C3.4 Conductor cross sections3.4 Conductor cross sections3.4.1 Feeder unitsConductor cross sectionsDesignFeeder units withbolted connectionFeeder units withfuse switchCentre feeder unitswith boltedconnectionTypeL1, L2, L3 N PEmin.mm²max.mm²BD2.-250-EE (1–3) × 6 1 × 150,2 × 70BD2.-400-EE (1–3) × 10 1) 1 × 240,2 × 120BD2.-1000-EE (1–3) × 10 1) 2 × 240,3 × 185BD2.-1250-EE (1–4) × 10 1) 3 × 300,4 × 240BD2C-250(315, 400)-EESCBD2C-630(800)-EESCBD2.-400-ME (1–3) × 10 1) 2 × 240,3 × 185min.mm²max.mm²(1–3) × 6 1 × 150.2 × 70(1–3) × 10 1) 1 × 240,2 × 120(1–3) × 10 1) 2 × 240,3 × 185(1–4) × 10 1) 3 × 300.4 × 240min.mm²max.mm²(1–3) × 6 1 × 150,2 × 70(1–3) × 10 1) 1 × 240,2 × 120(1–3) × 10 1) 2 × 240,3 × 185(1–4) × 10 1) 3 × 300,4 × 2401 x 10 1) 1 x 240 1 x 10 1) 1 x 240 Armouring M121 x 10 1) 1 x 240 1 x 10 1) 1 x 240 Armouring M12(1–3) × 10 1) 2 × 240.3 × 185(1–3) × 10 1) 2 × 240,3 × 185BD2.-1000-ME (1–5) × 10 1 ) (1–5) × 300 (1–5) × 10 1) (1–5) × 300 (1–5) × 10 1) (1–5) × 300 M12Size of fixingscrews, boltsL1, L2, L3, N,PEM10M12M12M12M121)Minimum permissible cable cross section for cable lugsCable and wire entriesType BD2.-250-EE BD2.-400-EE BD2.-1000-EE, BD2.-400-MECable grommets for cablediametersBD2.-1000-MEBD2.-1250-EE1 x KT3 1) 2 x KT4 1) 3 x KT4 1) 6 x KT4 1) 4 x KT4 1)mm 14...54 14...68 14...68 14...68 14...681)With strain reliefCable entry plate single-core system (undrilled cable entry plates)Type BD2.-250-EE BD2.-400-EE BD2.-1000-EE BD2.-1250-EECable entry plate BD2-250-EBAL BD2-400-EBAL BD2-1000-EBAL BD2-1250-EBALNo. of cable entries (maximum) 10 x M32,10 x M40 15 x M40,36 x M505 x M406 x M50 and 4 x M40Plastic cable glands with strain relief must be used (these are not included in the scope ofsupply).Planning with SIVACON 8 PSPlanning Manual, 10/2007, A5E01541101-01 67