SolarEdge

More documents

Recommendations

Info

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING! The inverter cover must be opened only after shutting off the inverter ON/OFF switch located at the bottom of the inverter. This disables the DC voltage inside the inverter. Wait five minutes before opening the cover. Otherwise, there is a risk of electric shock from energy stored in the capacitors. WARNING! Before operating the inverter, ensure that the inverter AC power cable and wall outlet are grounded properly. WARNING! Opening the inverter and repairing or testing under power must be performed only by qualified service personnel familiar with this inverter. WARNING! Do not touch the PV panels or any rail system connected when the inverter switch is ON, unless grounded. CAUTION! This unit must be operated under the specified operating specifications, as described in the latest technical specification datasheet, available on the SolarEdge website at http://www.solaredge.com/groups/products/overview. CAUTION! The inverters are IP65 rated. Unused connectors and glands should be sealed with the provided seals. NOTE Use PV modules rated according to IEC 61730 class A. NOTE The symbol appears at grounding points on the SolarEdge equipment. This symbol is also used in this manual. SolarEdge-Installation Guide MAN-01-00057-3.1 7
IMPORTANT SAFETY INSTRUCTIONS NOTE The following warning symbols appear on the inverter warning label: Risk of electric shock Risk of electric shock from energy stored in the capacitor. Do not remove cover until 5 minutes after disconnecting all sources of supply. Hot surface – To reduce the risk of burns, do not touch. 8 SolarEdge-Installation Guide MAN-01-00057-3.1
Page 1 and 2: SolarEdge Installation Guide For Eu
Page 3 and 4: Support and Contact Information Sup
Page 5 and 6: Support and Contact Information LCD
Page 7: HANDLING AND SAFETY INSTRUCTIONS HA
Page 11 and 12: Installation Procedure Installation
Page 13 and 14: Chapter 2: Installing the Power Opt
Page 15 and 16: Step 1: Mounting the Power Optimize
Page 17 and 18: Step 4: Verifying Proper Power Opti
Page 19 and 20: Chapter 3: Installing the Inverter
Page 21 and 22: Mounting the Inverter • AC output
Page 23 and 24: Mounting the Inverter 2. Position t
Page 25 and 26: Mounting the Inverter Figure 9: Han
Page 27 and 28: Connecting the AC Grid to the Inver
Page 29 and 30: Selecting a Residual Current Device
Page 31 and 32: Step 1: Activating the System 9. Cl
Page 33 and 34: Step 2: Pairing Power Optimizers to
Page 35 and 36: Step 4: Reporting and Monitoring In
Page 37 and 38: Chapter 6: User Interface Chapter 6
Page 39 and 40: Configuring the Inverter Using the
Page 41 and 42: Configuring the Inverter Using the
Page 43 and 44: Configuration Menu Options Maintena
Page 45 and 46: Communication LAN Conf: RS485-1 Con
Page 47 and 48: Maintenance Maintenance Select Main
Page 49 and 50: Status Screens - Operational Mode S
Page 51 and 52: Telemetry Status Telemetry Status T
Page 53 and 54: Communication Ports Status • IP:
Page 55 and 56: Power Control Status Power Control
Page 57 and 58: Removing the Inverter Cover Figure
Page 59 and 60:
Creating an Ethernet (LAN) Connecti
Page 61 and 62:
Creating an RS485 Bus Connection 9.
Page 63 and 64:
Creating an RS485 Bus Connection 6.
Page 65 and 66:
Creating a Wireless ZigBee Connecti
Page 67 and 68:
Appendix A: Errors and Troubleshoot
Page 69 and 70:
Troubleshooting RS485 Communication
Page 71 and 72:
Error Codes WARNING! All Warnings a
Page 73 and 74:
Error Codes Error # Single Phase Er
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Power Optimizer Troubleshooting Pow
Page 81 and 82:
Power Optimizer Troubleshooting Pro
Page 83 and 84:
Appendix B: Technical Specification
Page 85 and 86:
Appendix B: Technical Specification
Page 87 and 88:
Technical Specifications - Three Ph
Page 89 and 90:
SE4K - SE12.5K SE4K SE5K SE7K SE8K
Page 91 and 92:
SE15K - SE33.3K SE15K - SE33.3K 1 S
Page 93 and 94:
SE15K - SE33.3K SE15K SE16K SE17K S
Page 95 and 96:
SE15K - SE33.3K SE15K SE16K SE17K S
Page 97 and 98:
Appendix C: Mechanical Specificatio
Page 99 and 100:
Single Phase Inverter and Mounting
Page 101 and 102:
Three Phase Inverter and Mounting B
Page 103 and 104:
Three Phase Inverter and Mounting B
Page 105 and 106:
Connecting the AC Grid to the Inver
Page 107 and 108:
Connecting the Strings to the DC Sa
Page 109 and 110:
Appendix E: Safe DC Appendix E: Saf
Page 111 and 112:
External Fan Replacement 3. Use a P
Page 113:
Adding, Removing, or Replacing Powe
show all

SolarEdge

Create successful ePaper yourself

Delete template?

Save as template?