Cutler-Hammer - Eaton Canada
Cutler-Hammer - Eaton Canada
Cutler-Hammer - Eaton Canada
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
INDEX<br />
Design of Power Distribution System and; 2-9<br />
Example of Calculation; 2-9<br />
Relationship to Full Load Current Rating and; 2-9<br />
Solvent Withstand; 2-39<br />
Source Impedance (See Input Line Impedance)<br />
Specifications; S-3, 2-34 to 2-40<br />
General Specifications; 2-36 to 2-40<br />
Nameplate Identification; 2-35<br />
SPEED, Range of Adjustment; 4-3, 4-9, 4-13, 4-22 and 4-23<br />
Speed; S-3, 1-1, 2-5, 3-5, 5-3 to 5-4<br />
Speed Follower; 4-5, 4-16, 4-18, 4-20<br />
SPEED FOLLOWER, Range of Adjustment; 4-5, 4-18<br />
Speed Setpoint, parameter; 4-3, 4-13, A-2, A-5<br />
(SPEED SETPOINT)<br />
Standards; 2-36, 2-39<br />
ANSI C62.41; 2-39<br />
ASTM D999; 2-39<br />
ASTM-896; 2-39<br />
FCC Part 15B; 2-39<br />
IEC 801; 2-36 and 2-39<br />
IEEE Standard 446; 2-36<br />
MIL-STD 202E; 2-39<br />
Standby Power Generation; 2-12<br />
Input Line Considerations and; 2-12<br />
Start button 3-2, 3-6, 4-25, 5-2<br />
Start Into Spinning Motor, parameter; 4-11, 4-24, A-3, A-5<br />
(SPINNING MOTOR)<br />
Starting your drive 3-6<br />
Stop button 3-2, 3-7, 4-25, 5-2<br />
Stopping your drive 3-7<br />
STOP, mode; 3-7, 4-7 and 4-8<br />
Stop Profile, parameter; 4-10, 4-23, A-3, A-5<br />
(STOP PROFILE)<br />
Storage Conditions; 2-38<br />
Storing The Drive; 2-4<br />
T<br />
Terminal Block; S-3, 2-14, 2-37, 4-13<br />
Three Phase Motor; 2-7<br />
Three Phase Motors; 1-1<br />
Time Between Restart Attempts, parameter; 4-10,<br />
4-23, A-3, A-5<br />
(RESTART DELAY)<br />
THERMAL OVERLOAD, fault message; 5-5<br />
Torque; 1-1, 2-7, 4-5, 4-17, A-2, A-4<br />
Motor Operation at Reduced Speed and; 2-7<br />
Transient Protection; 2-36<br />
AF93/IS903 Instruction Manual<br />
I-8<br />
U<br />
UL; S-3, 2-39<br />
Unpacking The Drive; 2-4<br />
Unusual Operating Requirements; 2-19<br />
Up button; 3-2, 3-5, 3-10 to 3-12, 4-4, 4-13, 4-25<br />
Upper Display, parameter; 4-3, 4-13, A-2, A-5<br />
(UPPER DISPLAY)<br />
V<br />
Ventilation; 2-22 to 2-25<br />
W<br />
Warning; S-1, S-2, S-3, S-4, S-5 to S-6, 2-4, 2-7, 2-16, 2-18<br />
Application and Installation; S-3<br />
Electric Shock; 2-16, 2-18<br />
General Meaning; S-2<br />
Heavy Equipment Handling; S-4, 2-4<br />
Input Line Impedance; S-3<br />
Operation Above 60 Hz; S-3<br />
Rotating Mechanical Equipment; S-4<br />
Where To Locate Drive; 2-5<br />
Wire Size Capacity; 2-8, 2-10, 2-13<br />
Input Terminals; 2-8, 2-10<br />
Output Terminals; 2-10, 2-13<br />
Z<br />
ZERO SPEED, Range of Adjustment; 4-7, 4-8, 4-22
Change language