Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

Specifications INSTALLATION Enclosure Style G - NEMA 1 J - NEMA 12 Voltage B - 200-240 V; 50/60 Hz C - 380-480 V, 50/60 Hz AF93/IS903 Instruction Manual 2-40 Legend *Horsepower (Examples) 005 - 5 Horsepower Application Rating D - Dual Rated V - Variable Torque AF93/IS903 AG0C 005D ABCD Catalog Number Codes A - B - C - D - E - F - G - H - A B C D E F G H Base Catalog Number Series Enclosure Special Voltage *Horsepower Application Rating * Horsepower must be derated by 0.5 if single phase input power is used with 240 VAC units. Modification Codes (See AF93/IS903 Catalog) Catalog Number Decoding for Drives Operating on 3-Phase Input Power Figure 2-14
SECTION 3 Using Your Keypad About This Section This section of your Instruction Manual identifies each keypad indicator and button and describes their function. After you review this section you will understand how to: ¥ Select which parameters will be displayed on your keypad LCD display. ¥ Change the settings of selected parameters using the keypad. ¥ Issue selected commands from the keypad. Caution Make sure you read, understand and follow all of the Safety Statements in the Safety section of this guide and all of the operation instructions in this manual before you operate your Adjustable Frequency Drive. AF93/IS903 Instruction Manual 3-1
Page 1 and 2: Instruction Manual For Models AF93/
Page 3 and 4: Table of Contents Page Safety .....
Page 5 and 6: Safety Cutler-Hammer has made every
Page 7 and 8: Danger High Voltage Internal parts
Page 9 and 10: About This Manual SECTION 1 Introdu
Page 11 and 12: About This Section SECTION 2 Instal
Page 13 and 14: Pre-Installation This part of the I
Page 15 and 16: Where to Locate Drive Consider the
Page 17 and 18: Application Considerations Motor Se
Page 19 and 20: Input Line Considerations The value
Page 21 and 22: Input Line Considerations Harmonic
Page 23 and 24: Output Power Considerations To comp
Page 25 and 26: Installation Check List To help ass
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37 and 38: Fan Keypad Cover Keypad Remote Driv
Page 39 and 40: Optional Dynamic Brake Module Servi
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43 and 44: Chassis Gound Screw See Note 3 ILOO
Page 45 and 46: Nameplate Identification Adjustable
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49: ¥ Heat Dissipation Specifications
Page 53 and 54: Setup Button (item 14) - Pressing t
Page 55 and 56: Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58: Stopping Your Drive From Your Keypa
Page 59 and 60: Using the Forward/Reverse Button SE
Page 61 and 62: Changing Parameter Settings SECTION
Page 63 and 64: Step 6. Press Setup button. Changin
Page 65 and 66: Changing Parameter Settings SECTION
Page 67 and 68: SECTION 4 Using The Parameters Abou
Page 69 and 70: Customer Setting Factory Setting No
Page 79 and 80: AF93/IS903 Parameter Descriptions U
Page 93 and 94: SECTION 5 Troubleshooting This sect
Page 95 and 96: Solutions To Drive Problems TROUBLE
Page 97 and 98: Solutions To Drive Problems TROUBLE
Page 99 and 100: See Note 1 DVM A B Checking DC Bus
Page 101 and 102:
About This Section Appendix This se
Page 103 and 104:
28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106:
17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108:
0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110:
Note that parameters are listed wit
Page 111 and 112:
EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114:
Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116:
Selecting Parameters; 3-10 Changing
Page 117:
Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?