Cutler-Hammer - Eaton Canada
Cutler-Hammer - Eaton Canada
Cutler-Hammer - Eaton Canada
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
AF93/IS903 Parameter Descriptions<br />
USING THE PARAMETERS<br />
Note that ACCEL TIME and DECEL TIME are<br />
generated by the AF93/IS903 software and due<br />
to actual application the motor may not come to<br />
full speed or decelerate to a stop in exactly the<br />
length of time you have set.<br />
Accel Time<br />
Specifications<br />
Parameter Number: 11<br />
Mnemonic: ACCEL TIME<br />
Range of Adjustment: 0.1 to 999 sec<br />
Run Locked?: No<br />
Factory Setting: 5 sec<br />
This parameter defines the time it takes the drive to<br />
go from zero to Maximum Speed. The drive will not<br />
exceed the load limit to meet this acceleration time.<br />
Decel Time<br />
Specifications<br />
Parameter Number: 12<br />
Mnemonic: DECEL TIME<br />
Range of Adjustment: 0.1 to 999 sec<br />
Run Locked?: No<br />
Factory Setting: 5 sec<br />
This parameter defines the time it takes the drive to<br />
go from Maximum Speed to zero. On high inertia,<br />
low friction applications, the drive may decelerate in<br />
a greater length of time unless a braking resistor is<br />
present.<br />
Accel/Decel 2 or Jog<br />
Specifications<br />
Parameter Number: 13<br />
Mnemonic: ACCEL2 OR JOG<br />
Range of Adjustment: ÒACCEL/DECEL 2Ó or<br />
ÒJOGÓ<br />
Run Locked?: Yes<br />
Factory Setting: ÒJOGÓ<br />
This parameter defines whether the drive will have<br />
a secondary acceleration/deceleration time (Accel<br />
Time 2 and Decel Time 2) or implement the jog<br />
speed function (Jog Speed) when terminal 11 is<br />
connected to terminal 7 while the drive is in the<br />
REMOTE mode.<br />
AF93/IS903 Instruction Manual<br />
4-16<br />
If ÒACCEL/DECEL 2Ó is chosen, the drive is in<br />
REMOTE mode, and terminal 11 is connected to<br />
terminal 7, Accel Time (parameter 11) and Decel<br />
Time (parameter 12) are ignored. The drive will<br />
use Accel Time 2 (parameter 14) and Decel Time<br />
2 (parameter 15) instead. Note that both the<br />
acceleration and deceleration times are affected.<br />
If ÒJOGÓ is selected, whenever terminal 11 is<br />
connected to terminal 7 and RUN enable is<br />
present (terminal 8 connected to terminal 7), the<br />
drive goes into JOG mode at the speed set by<br />
Jog Speed (parameter 33). Note that Jog<br />
overrides the speed setpoint established by<br />
ÒSPEED FOLLOWERÓ, ÒPI REGULATORÓ, and<br />
Preset Speed x (parameters 26 to 32). See<br />
Remote Function, Priority Interaction in REMOTE<br />
Mode, for more information.<br />
Accel Time 2<br />
Specifications<br />
Parameter Number: 14<br />
Mnemonic: ACCEL TIME 2<br />
Range of Adjustment: 0.1 to 999 sec<br />
Run Locked?: No<br />
Factory Setting: 5 sec<br />
If ÒACCEL/DECEL 2Ó is chosen, the drive is in<br />
REMOTE mode, and terminal 11 is connected to<br />
terminal 7, this parameter defines the time it<br />
takes the drive to go from zero to Maximum<br />
Speed.<br />
Decel Time 2<br />
Specifications<br />
Parameter Number: 15<br />
Mnemonic: DECEL TIME 2<br />
Range of Adjustment: 0.1 to 999 sec<br />
Run Locked?: No<br />
Factory Setting: 5 sec<br />
If ÒACCEL/DECEL 2Ó (parameter 13) is chosen,<br />
the drive is in REMOTE mode, and terminal 11 is<br />
connected to terminal 7, this parameter defines<br />
the time it takes the drive to go from Maximum<br />
Speed to zero.