Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

Pre-Installation INSTALLATION Analog and Digital Signal Considerations To comply with the design of the drive and local and nationally recognized codes, consider proper analog and digital signal wiring when you plan your Adjustable Frequency Drive installation. Note: Make sure you use the most recent version of the codes when you install your AF93/IS903 drive. External Fault Signal Some configurations, such as an optional overload interlock relay, provide an external fault signal to the drive so the drive will not start if the relay has tripped and has not been reset. If this or other option that requires an external fault signal is installed by the factory, the signal is factory wired. See the connection diagrams in the Drawings section of this manual for details. Analog and Digital Signal Wiring ¥ 18 AWG wire size is recommended. Minimum wire size is 20 AWG. Maximum wire size is 16 AWG. ¥ One conductor per terminal for 16 AWG conductors. Two conductors per terminal at 18 AWG. Three conductors per terminal at 20 AWG. ¥ Maximum length is 500 feet; call your <strong>Cutler</strong>- <strong>Hammer</strong> sales representative or distributor for longer runs. ¥ Use shielded cable for the analog signal conductors where indicated on the terminal block connection diagram. Typically, shielding is required for all analog input and output runs. All digital signal runs over 75 feet long should be shielded. ¥ Only ground the shield conductor of shielded cable at the terminal block of the drive for input signals only. Output signals should not be grounded at the drive end of the cable but should be grounded at the device. AF93/IS903 Instruction 2-14 ¥ The analog and digital signal conductors must be made of copper with a temperature rating of at least 167¡F (75¡C). Analog and Digital Conductor Routing For 7.5 to 25 Hp AF93/IS903: ¥ If you use conduit: Never route analog and digital wiring from any equipment in the same conduit as input or output power wiring. Do not run AF93/IS903 Adjustable Frequency Drive analog and digital signal conductors in the same conduit that has control wiring for other equipment. For 2 to 5 Hp AF93/IS903: If you use conduit, use separate conduit for input and output power and AF93/IS903 control wiring, up to the AF93/IS903 drive. At the drive use a T-coupling to combine the input power and output power wiring and attach to conduit entry point. ¥ If you use cable trays: Never route analog and digital wiring from any equipment in the same cable tray as input or output power wiring. Separate analog and digital wiring for your AF93/IS903 drive from other control equipment wiring using a metal tray divider or keeping the conductors at least 2 inches apart. Trays containing analog and digital wiring should be separated from trays containing low voltage (up to 30 volts) power wiring by at least 9 inches. Trays containing analog and digital wiring should be separated from trays containing medium voltage (between 30 and 150 volts) power wiring by at least 18 inches.
Installation Check List To help assure a safe and reliable drive installation, make sure that the following tasks have been properly completed. You can find complete information on the task by referring to the Section(s) listed in the right column: Installation Tasks ❐ Pre-Installation Handling of Drive After Delivery Where to Locate Drive Application Considerations Input Line Considerations Output Power Considerations Analog and Digital Signal Considerations Page 2-3 2-4 2-5 2-6 to 2-7 2-8 to 2-12 2-13 2-14 AF93/IS903 Instruction Manual 2-15
Page 1 and 2: Instruction Manual For Models AF93/
Page 3 and 4: Table of Contents Page Safety .....
Page 5 and 6: Safety Cutler-Hammer has made every
Page 7 and 8: Danger High Voltage Internal parts
Page 9 and 10: About This Manual SECTION 1 Introdu
Page 11 and 12: About This Section SECTION 2 Instal
Page 13 and 14: Pre-Installation This part of the I
Page 15 and 16: Where to Locate Drive Consider the
Page 17 and 18: Application Considerations Motor Se
Page 19 and 20: Input Line Considerations The value
Page 21 and 22: Input Line Considerations Harmonic
Page 23: Output Power Considerations To comp
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37 and 38: Fan Keypad Cover Keypad Remote Driv
Page 39 and 40: Optional Dynamic Brake Module Servi
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43 and 44: Chassis Gound Screw See Note 3 ILOO
Page 45 and 46: Nameplate Identification Adjustable
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49 and 50: ¥ Heat Dissipation Specifications
Page 51 and 52: SECTION 3 Using Your Keypad About T
Page 53 and 54: Setup Button (item 14) - Pressing t
Page 55 and 56: Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58: Stopping Your Drive From Your Keypa
Page 59 and 60: Using the Forward/Reverse Button SE
Page 61 and 62: Changing Parameter Settings SECTION
Page 63 and 64: Step 6. Press Setup button. Changin
Page 65 and 66: Changing Parameter Settings SECTION
Page 67 and 68: SECTION 4 Using The Parameters Abou
Page 69 and 70: Customer Setting Factory Setting No
Page 75 and 76:
Customer Setting Factory Setting No
Page 77 and 78:
Customer Setting Factory Setting No
Page 79 and 80:
AF93/IS903 Parameter Descriptions U
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
SECTION 5 Troubleshooting This sect
Page 95 and 96:
Solutions To Drive Problems TROUBLE
Page 97 and 98:
Solutions To Drive Problems TROUBLE
Page 99 and 100:
See Note 1 DVM A B Checking DC Bus
Page 101 and 102:
About This Section Appendix This se
Page 103 and 104:
28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106:
17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108:
0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110:
Note that parameters are listed wit
Page 111 and 112:
EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114:
Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116:
Selecting Parameters; 3-10 Changing
Page 117:
Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?