Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

Quick Start Before applying power to the unit, make sure it is properly wired. The input line should be connected to terminals L1, L2, and L3, and the motor should be connected to terminals T1, T2, and T3. The unit should also be properly grounded in accordance with the connection drawings in the AF93/IS903 Instruction Manual. To run the drive in KEYPAD mode, make sure a jumper or customer permissive circuit is connected between terminal 7 and 8, and terminal 7 and 15. See the connection drawings in the AF93/IS903 Instruction Manual. To Start Drive and Set Speed Complete the following procedure to start the drive and set the speed (to 1200 RPM for example). 1. Apply power and verify both lines of LCD display are lit. Scroll SETUP Change Settings Keypad Remote <strong>Cutler</strong>-<strong>Hammer</strong> OPERATE SELECT AF93/IS903 Instruction Manual 2. Press the SELECT button until Keypad Indicator is lit. 3. Verify the Operate Indicator is lit. If not, press the OPERATE button. 4. Press the START button. 5. Press the UP or DOWN button and verify SPEED SETPOINT appears on the top line of the LCD and speed in RPMs appears on the bottom line. 6. Use the UP or DOWN button to set the drive at 1200 RPM. 7. If reversal of rotation is required, press the F/R button. Press the STOP button to stop the drive. Forward Reverse UP DOWN F/R START STOP RUN FAULT ETN-10.A
Table of Contents Page Safety ...............................................S-1 The Meaning of Safety Statements ................S-2 AF93/IS903 Safety Statements ....................S-2 Introduction .........................................1-1 Installation...........................................2-1 Pre-Installation ....................................2-3 Installation Check List .............................2-15 Drawings..........................................2-21 Specifications .....................................2-33 Using Your Keypad ..................................3-1 About Your Keypad................................3-2 Keypad Tips and Modes ...........................3-5 Using the Start Button .............................3-6 Using the Stop Button .............................3-7 Using the Forward/Reverse Button.................3-8 Changing Parameter Settings......................3-10 AF93/IS903 Instruction Manual i
Page 1: Instruction Manual For Models AF93/
Page 5 and 6: Safety Cutler-Hammer has made every
Page 7 and 8: Danger High Voltage Internal parts
Page 9 and 10: About This Manual SECTION 1 Introdu
Page 11 and 12: About This Section SECTION 2 Instal
Page 13 and 14: Pre-Installation This part of the I
Page 15 and 16: Where to Locate Drive Consider the
Page 17 and 18: Application Considerations Motor Se
Page 19 and 20: Input Line Considerations The value
Page 21 and 22: Input Line Considerations Harmonic
Page 23 and 24: Output Power Considerations To comp
Page 25 and 26: Installation Check List To help ass
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37 and 38: Fan Keypad Cover Keypad Remote Driv
Page 39 and 40: Optional Dynamic Brake Module Servi
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43 and 44: Chassis Gound Screw See Note 3 ILOO
Page 45 and 46: Nameplate Identification Adjustable
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49 and 50: ¥ Heat Dissipation Specifications
Page 51 and 52: SECTION 3 Using Your Keypad About T
Page 53 and 54:
Setup Button (item 14) - Pressing t
Page 55 and 56:
Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58:
Stopping Your Drive From Your Keypa
Page 59 and 60:
Using the Forward/Reverse Button SE
Page 61 and 62:
Changing Parameter Settings SECTION
Page 63 and 64:
Step 6. Press Setup button. Changin
Page 65 and 66:
Changing Parameter Settings SECTION
Page 67 and 68:
SECTION 4 Using The Parameters Abou
Page 69 and 70:
Customer Setting Factory Setting No
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
AF93/IS903 Parameter Descriptions U
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
SECTION 5 Troubleshooting This sect
Page 95 and 96:
Solutions To Drive Problems TROUBLE
Page 97 and 98:
Solutions To Drive Problems TROUBLE
Page 99 and 100:
See Note 1 DVM A B Checking DC Bus
Page 101 and 102:
About This Section Appendix This se
Page 103 and 104:
28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106:
17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108:
0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110:
Note that parameters are listed wit
Page 111 and 112:
EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114:
Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116:
Selecting Parameters; 3-10 Changing
Page 117:
Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?