Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

Drawings INSTALLATION AF93/IS903 Instruction Manual 2-28 Front Panel Cover Scroll SETUP Change Settings Keypad Remote OPERATE SELECT Forward Reverse UP DOWN F/R START STOP RUN FAULT Keypad Conduit Holes Rear Cover Component Identification for 15, 20, and 25 hp Frame Size Figure 2-7 Fan Heat Sink ETN-93-20HP
Optional Dynamic Brake Module Service Entrance L1 L2 L3 Service GND L ILOOP AGND POT_WPR POT_HI AOUT1 AOUT2 DIGCOM STOP START FWD/REV ACC2/JOG PRST1 PRST2 PRST3 EXTFLT RLY1A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 L 115V, 1¿, 60Hz Customer Supplied Fused Disconnect or Circuit Breaker Panel See Note 1 DB1 +BUS L1 L2 L3 T1 T2 T3 Current Transformer (see Input Line Considerations in Pre-Installation instructions) To Logic Board - Factory Wired Connection Drawing for 2, 3, and 5 hp Frame Size Figure 2-8 Drawings INSTALLATION RLY1B RLY2A RLY2B FLTNC FLTCOM FLTNO See Note 2 Note 1 : Customer supplied jumpers (7 and 8, 7 and 15) are required for running drive in KEYPAD mode. See table 2-2 on page 2-37. Note 2 : Power terminal tightening torque range is 16-18 in. lbs. on terminals L1, L2, L3, T1, T2, T3, and ground lugs. Motor GND T3 AF93-5HpConn AF93/IS903 Instruction Manual T2 T1 NEMA-B Motor Wiring Box 2-29
Page 1 and 2: Instruction Manual For Models AF93/
Page 3 and 4: Table of Contents Page Safety .....
Page 5 and 6: Safety Cutler-Hammer has made every
Page 7 and 8: Danger High Voltage Internal parts
Page 9 and 10: About This Manual SECTION 1 Introdu
Page 11 and 12: About This Section SECTION 2 Instal
Page 13 and 14: Pre-Installation This part of the I
Page 15 and 16: Where to Locate Drive Consider the
Page 17 and 18: Application Considerations Motor Se
Page 19 and 20: Input Line Considerations The value
Page 21 and 22: Input Line Considerations Harmonic
Page 23 and 24: Output Power Considerations To comp
Page 25 and 26: Installation Check List To help ass
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37: Fan Keypad Cover Keypad Remote Driv
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43 and 44: Chassis Gound Screw See Note 3 ILOO
Page 45 and 46: Nameplate Identification Adjustable
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49 and 50: ¥ Heat Dissipation Specifications
Page 51 and 52: SECTION 3 Using Your Keypad About T
Page 53 and 54: Setup Button (item 14) - Pressing t
Page 55 and 56: Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58: Stopping Your Drive From Your Keypa
Page 59 and 60: Using the Forward/Reverse Button SE
Page 61 and 62: Changing Parameter Settings SECTION
Page 63 and 64: Step 6. Press Setup button. Changin
Page 65 and 66: Changing Parameter Settings SECTION
Page 67 and 68: SECTION 4 Using The Parameters Abou
Page 69 and 70: Customer Setting Factory Setting No
Page 79 and 80: AF93/IS903 Parameter Descriptions U
Page 89 and 90:
AF93/IS903 Parameter Descriptions U
Page 91 and 92:
AF93/IS903 Parameter Descriptions U
Page 93 and 94:
SECTION 5 Troubleshooting This sect
Page 95 and 96:
Solutions To Drive Problems TROUBLE
Page 97 and 98:
Solutions To Drive Problems TROUBLE
Page 99 and 100:
See Note 1 DVM A B Checking DC Bus
Page 101 and 102:
About This Section Appendix This se
Page 103 and 104:
28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106:
17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108:
0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110:
Note that parameters are listed wit
Page 111 and 112:
EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114:
Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116:
Selecting Parameters; 3-10 Changing
Page 117:
Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

Create successful ePaper yourself

Delete template?

Save as template?