Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

USING THE PARAMETERS AF93/IS903 Instruction Manual 4-12
AF93/IS903 Parameter Descriptions USING THE PARAMETERS The parameter descriptions are in the same order as they appear in the AF93/IS903 Parameters List. Note that Òterminal numbersÓ in the descriptions refer to the AF93/IS903 terminal block (see Fig. 2-8, 2-9, 2-10 or 2-11 for terminal block descriptions). Upper Display Specifications Parameter Number: 1 Mnemonic: UPPER DISPLAY Range of Adjustment: ÒSPEEDÓ (RPM), ÒFREQUENCYÓ (Hz), ÒLOADÓ (%), ÒCURRENTÓ (Amps), ÒMOTOR VOLTSÓ (Volts), ÒPOWERÓ (Hp), ÒELAPSED TIMEÓ (0-6553.5 hours). Units are shown in the parenthesis. Run Locked?: No Factory Setting: ÒSPEEDÓ This parameter allows you to select the Operation Display Parameters you want to appear on the upper line of the driveÕs LCD when the drive is in the OPERATE mode. Elapsed time resets to 0 when 6553.5 hours are exceeded. Lower Display Specifications Parameter Number: 2 Mnemonic: LOWER DISPLAY Range of Adjustment: ÒSPEEDÓ (RPM), ÒFREQUENCYÓ (Hz), ÒLOADÓ (%), ÒCURRENTÓ (Amps), ÒMOTOR VOLTSÓ (Volts), ÒPOWERÓ (Hp), ÒELAPSED TIMEÓ (0-6553.5 hours). Units are shown in the parenthesis. Run Locked?: No Factory Setting: ÒLOADÓ This parameter allows you to select the Operation Display Parameters you want to appear on the lower line of the driveÕs LCD when the drive is in the OPERATE mode. Elapsed time resets to 0 when 6553.5 hours are exceeded. Speed Setpoint Specifications Parameter Number: 3 Mnemonic: SPEED SETPOINT Range of Adjustment: Between Minimum Speed and Maximum Speed Run Locked?: No Factory Setting: 0 This parameter defines the speed setpoint used only in the KEYPAD mode. This is the only way to change speed setpoint in the KEYPAD mode. Note that Speed Setpoint is ignored if the drive is REMOTE mode. When drive is in RUN and KEYPAD modes and you press the Up or Down button, drive goes directly to the Speed Setpoint parameter. Pressing the Up or Down button additional times will change the current value of the Speed Setpoint parameter. Minimum Speed Specifications Parameter Number: 4 Mnemonic: MIN SPEED Range of Adjustment: 25 to 10800 RPM Run Locked?: No Factory Setting: 50 RPM This parameter defines the minimum speed limit at which the drive will be allowed to operate. Minimum speed must be set lower than maximum speed. Maximum Speed Specifications Parameter Number: 5 Mnemonic: MAX SPEED Range of Adjustment: 25 to 10800 RPM Run Locked?: No Factory Setting: 1800 RPM This parameter defines the maximum speed limit at which the drive will be allowed to operate. If the drive reaches the Load Limit (parameter 22) or ÒANALOG LOAD LIMÓ (parameter 23) and you are ramping up to the maximum speed, the drive will go into foldback and stay at the speed where the load limit was reached. AF93/IS903 Instruction Manual 4-13
Page 1 and 2:
Instruction Manual For Models AF93/
Page 3 and 4:
Table of Contents Page Safety .....
Page 5 and 6:
Safety Cutler-Hammer has made every
Page 7 and 8:
Danger High Voltage Internal parts
Page 9 and 10:
About This Manual SECTION 1 Introdu
Page 11 and 12:
About This Section SECTION 2 Instal
Page 13 and 14:
Pre-Installation This part of the I
Page 15 and 16:
Where to Locate Drive Consider the
Page 17 and 18:
Application Considerations Motor Se
Page 19 and 20:
Input Line Considerations The value
Page 21 and 22:
Input Line Considerations Harmonic
Page 23 and 24:
Output Power Considerations To comp
Page 25 and 26:
Installation Check List To help ass
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37 and 38: Fan Keypad Cover Keypad Remote Driv
Page 39 and 40: Optional Dynamic Brake Module Servi
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43 and 44: Chassis Gound Screw See Note 3 ILOO
Page 45 and 46: Nameplate Identification Adjustable
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49 and 50: ¥ Heat Dissipation Specifications
Page 51 and 52: SECTION 3 Using Your Keypad About T
Page 53 and 54: Setup Button (item 14) - Pressing t
Page 55 and 56: Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58: Stopping Your Drive From Your Keypa
Page 59 and 60: Using the Forward/Reverse Button SE
Page 61 and 62: Changing Parameter Settings SECTION
Page 63 and 64: Step 6. Press Setup button. Changin
Page 65 and 66: Changing Parameter Settings SECTION
Page 67 and 68: SECTION 4 Using The Parameters Abou
Page 69 and 70: Customer Setting Factory Setting No
Page 77: Customer Setting Factory Setting No
Page 81 and 82: AF93/IS903 Parameter Descriptions U
Page 93 and 94: SECTION 5 Troubleshooting This sect
Page 95 and 96: Solutions To Drive Problems TROUBLE
Page 97 and 98: Solutions To Drive Problems TROUBLE
Page 99 and 100: See Note 1 DVM A B Checking DC Bus
Page 101 and 102: About This Section Appendix This se
Page 103 and 104: 28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106: 17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108: 0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110: Note that parameters are listed wit
Page 111 and 112: EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114: Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116: Selecting Parameters; 3-10 Changing
Page 117: Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?