Cutler-Hammer - Eaton Canada

More documents

Recommendations

Info

Specifications AF93/IS903 Instruction Manual 2-34 This part of the Installation section of this Instruction Manual provides the following specifications: ¥ Nameplate Identification ¥ General Specifications
Nameplate Identification Adjustable Frequency AC Drive Cat No: Input: Output: 150% Load Rating for 1 Minute Nominal HP: V 3PH HZ A RMS V 3PH HZ A RMS @ Volts 9 Max Ambient ¡C 12 Enclosure Type: Grounding Required <strong>Cutler</strong> <strong>Hammer</strong> Corporation Solid State Motor Control 13 Oldsmar, Florida USA 34677 Legend: 2 5 1 10 11 1. Cat. No: - AF93/IS903 drives are available in various models with different ratings, specifications and features as required for different applications. Figure 2-11 summarizes the information coded into the catalog number. 2. Input V 3PH: - Rated input line voltage; 3 phase. 3. Hz: - Rated input line frequency. 4. A RMS: - Rated input line current. 5. Output V 3PH: - Rated output line voltage; 3 phase. 6. Hz: - Rated output line frequency. 7. A RMS: - Rated output line current. 8. 150% or 110% Load Rating for 1 Minute - This statement refers to the fact that the drive is rated to run for either one minute at 150% or one minute at 110% of its output current rating (see item7). 8 3 6 4 7 14 ETN-AF93NAME Typical AF93/IS903 Nameplate Figure 2-13 Specifications INSTALLATION ! Caution The equipment warranty covers only the original nameplate rating. If the equipment is applied contrary to the nameplate rating, or if unauthorized equipment modifications are made, the warranty becomes invalid. 9. Max. Ambient: - Maximum allowable ambient temperature for continuous operation at rated operating conditions. 10. Nominal HP: - Maximum brake horsepower load subject to the output voltage limitation (see item 11). 11. Volts: - The voltage limitation used when the Nominal HP is measured (see item 10). 12. Enclosure Type: - The specific type of enclosure provided by the factory (see catalog for complete listing). 13. Bar Code: - All of the ordering and drive specific information is encoded at the factory. 14. Independent Testing Laboratory Logo: - Only certified or listed products are marked with a testing laboratory logo. AF93/IS903 Instruction Manual 2-35
Page 1 and 2: Instruction Manual For Models AF93/
Page 3 and 4: Table of Contents Page Safety .....
Page 5 and 6: Safety Cutler-Hammer has made every
Page 7 and 8: Danger High Voltage Internal parts
Page 9 and 10: About This Manual SECTION 1 Introdu
Page 11 and 12: About This Section SECTION 2 Instal
Page 13 and 14: Pre-Installation This part of the I
Page 15 and 16: Where to Locate Drive Consider the
Page 17 and 18: Application Considerations Motor Se
Page 19 and 20: Input Line Considerations The value
Page 21 and 22: Input Line Considerations Harmonic
Page 23 and 24: Output Power Considerations To comp
Page 25 and 26: Installation Check List To help ass
Page 27 and 28: Installation Tasks Installation Che
Page 29 and 30: Installation Tasks ❐ Initial Star
Page 31 and 32: Drawings This part of the Installat
Page 33 and 34: 1 ¿.281" [7.14 mm] (Two Places) 5.
Page 35 and 36: OPTION 1 Note: Multiple units can b
Page 37 and 38: Fan Keypad Cover Keypad Remote Driv
Page 39 and 40: Optional Dynamic Brake Module Servi
Page 41 and 42: Optional Dynamic Brake Module Servi
Page 43: Chassis Gound Screw See Note 3 ILOO
Page 47 and 48: Terminal Block The AF93/IS903 termi
Page 49 and 50: ¥ Heat Dissipation Specifications
Page 51 and 52: SECTION 3 Using Your Keypad About T
Page 53 and 54: Setup Button (item 14) - Pressing t
Page 55 and 56: Keypad Tips and Modes SECTION 3 Tip
Page 57 and 58: Stopping Your Drive From Your Keypa
Page 59 and 60: Using the Forward/Reverse Button SE
Page 61 and 62: Changing Parameter Settings SECTION
Page 63 and 64: Step 6. Press Setup button. Changin
Page 65 and 66: Changing Parameter Settings SECTION
Page 67 and 68: SECTION 4 Using The Parameters Abou
Page 69 and 70: Customer Setting Factory Setting No
Page 79 and 80: AF93/IS903 Parameter Descriptions U
Page 93 and 94: SECTION 5 Troubleshooting This sect
Page 95 and 96:
Solutions To Drive Problems TROUBLE
Page 97 and 98:
Solutions To Drive Problems TROUBLE
Page 99 and 100:
See Note 1 DVM A B Checking DC Bus
Page 101 and 102:
About This Section Appendix This se
Page 103 and 104:
28 29 30 31 32 33 34 35 36 37 38 39
Page 105 and 106:
17 43 53 50 26 27 28 29 30 31 32 25
Page 107 and 108:
0.208" [5.29 mm] 3.904" [99.15 mm]
Page 109 and 110:
Note that parameters are listed wit
Page 111 and 112:
EMI; 2-39 EMI Susceptibility; 2-39
Page 113 and 114:
Load Limit, parameter; 4-5, 4-17, A
Page 115 and 116:
Selecting Parameters; 3-10 Changing
Page 117:
Cutler-Hammer Solid State Motor Con
show all

Cutler-Hammer - Eaton Canada

Create successful ePaper yourself

Delete template?

Save as template?