BioQuip Equipment Catalog - Nature | Where knowledge meets ...
BioQuip Equipment Catalog - Nature | Where knowledge meets ...
BioQuip Equipment Catalog - Nature | Where knowledge meets ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
LAB<br />
1023 Series Adjustable Spreading Boards<br />
Used to pin wings of Lepidoptera into a fixed position until set, these<br />
spreading boards are unique in offering two separate methods of pin<br />
adjustment. Pinning strip is solid balsa, and accepts mounting pins at<br />
any depth along the pin shaft. This pinning strip may be adjusted<br />
vertically to suit user preference, and may be tacked or glued permanently<br />
in the desired position.<br />
Both boards feature adjustable horizontal pinning grooves, from 0 to<br />
7/8" (0-22mm). Basswood mounting surfaces are angled at 165°.<br />
Balsa pinning strip is 3/8" (16mm) thick, and 1" (20mm) wide. Boards<br />
are 12" (305mm) long.<br />
The 1023E board is used to mount varied sizes of specimens. Pinning<br />
surfaces are 2" wide (each side); board width is 4-7/8" (124mm).<br />
The 1023F board is intended for mounting large Lepidoptera. Pinning<br />
surfaces are 3" wide (each side); board width is 6-7/8" (175mm).<br />
1023E Spreading board, adjustable 21.75<br />
1023F Spreading board, adjustable 25.35<br />
Spreading Board Kit<br />
Ideal for Lepidopterists or entomology classes. Kit provides<br />
components for 12 spreading boards as described for the 1023E<br />
board listed above. User can assemble boards at considerably<br />
lower cost than if purchased in completed form.<br />
Center groove in the boards may be set at whatever width is<br />
required; or with the purchase of optional hardware kit, groove<br />
may be made adjustable from 0 to 7/8". Boards are 12" long,<br />
and basswood pinning surfaces are 2" wide. Balsa pinning strip<br />
may be set at height preferred by the user.<br />
A hammer is the only tool required for assembling boards with<br />
fixed pinning surfaces. A 3/16" drill is needed to complete adjustable<br />
boards. Instructions are included in each kit.<br />
1023K Spreading board kit of 12 87.95<br />
1023L Adjustable hardware for kit 26.20<br />
Versaboard<br />
<strong>BioQuip</strong> 7<br />
1023F 1023E 1022B 1022D 1022E<br />
Large pinning board provides<br />
a versatile yet inexpensive<br />
butterfly and moth<br />
spreading system. It has<br />
five grooves measuring from<br />
1/8" to 5/8" accommodating most specimen sizes on a single<br />
board. Deep groves cut into a 1-3/4"-thick styrofoam block<br />
allow for perfect positioning of specimens using any pin length.<br />
This easy-to-use pinning board is well suited for students or<br />
anyone on a tight budget. It is especially useful for field pinning<br />
because it can hold many specimens yet weighs under 4 ounces.<br />
Size: 11" long x 17" wide (28 x 43 cm).<br />
Price each 1 - 11 12+<br />
1031 Versaboard 4.50 4.05<br />
1022 Series Spreading Boards<br />
Adjustable<br />
Spreading Board<br />
Economy Spreading Boards<br />
Phone: (310) 667-8800 $ $ Fax: (310) 667-8808 $ $ www.bioquip.com<br />
1024E 1024C<br />
Spreading Boards<br />
1022W<br />
A longer length is available in 1022 pinning boards. The 3/8" rigid plastazote<br />
pinning strip holds a pin securely. Sufficient clearance permits mounting<br />
the insect at the top third of pin. Basswood mounting surfaces are<br />
angled at 165°. A 1/8" hardboard floor is provided to prevent accidental<br />
disturbance of pinned insects from the bottom. For large specimens,<br />
an adjustable board with flat pinning surfaces and two stabilizing adjustment<br />
screws on each end has been added to this series.<br />
Groove Width Price<br />
Fixed Boards, 18" (457mm) long<br />
1022A Spr. board 1/16" 2 mm 3-3/8" 87 mm 24.35<br />
1022B Spr. board 1/8" 3 mm 3-1/2" 90 mm 21.00<br />
1022C Spr. board 1/4" 7 mm 3-5/8" 93 mm 20.90<br />
1022D Spr. board 3/8" 10 mm 5-1/8" 131 mm 25.85<br />
Adjustable Board, 14" (356mm), 3/4" thick Plastazote pinning strip<br />
1022E Spr. board 0-13/16" 21 mm 5-1/2" 140 mm 27.20<br />
Adjustable Board, 18" (457mm), 3/8" thick Plastazote pinning strip<br />
1022W Spr. board 0-13/16" 21 mm 10" 254 mm 48.95<br />
Unique adjustable spreading board<br />
is unmatched in ease of use and<br />
versatility. Angled pinning surfaces<br />
are select balsa, 2-1/2" wide x 1/4"<br />
thick, fastened internally to a<br />
sturdy, vacuum-formed plastic<br />
base. The base is cemented to a rigid hardboard floor to avoid<br />
warping, provide rigidity and resistance to pressure.<br />
A plastazote foam strip, 3/8" thick, is inserted in the center<br />
pinning groove, which is adjustable from 0" to 3/4". Width is<br />
changed by pushing the balsa strips across the smooth surfaces<br />
to the desired width. Adjusting screws increase or decrease<br />
resistance as needed, or lock width into permanent<br />
position.<br />
Balsa pinning strips are resurfaced by wiping with wet, soapy<br />
sponge to close pin holes, then sanding with fine paper when dry.<br />
Overall length is 14-1/2" (36.8 cm); overall width is 5" (17.2 cm).<br />
1021 Adjustable spreading board 21.35<br />
Two moderately priced mounting boards for students and beginners.<br />
Basswood pinning surfaces are 2" wide (each side),<br />
angled at 165°. Pinning surfaces are attached to 1/2" composition<br />
board which also functions as pinning groove bottom. Groove<br />
on fixed board is 1/4" (7mm); groove on adjustable board is<br />
variable from 0 to 5/8" (0-16mm). Boards are 12" (305mm) long.<br />
Price each 1 - 11 12+<br />
1024C Spreading board 13.30 12.65<br />
1024E Spreading board, adjustable 18.80 17.85<br />
31